Forum: Model A (1928-31)
03-22-2024, 01:39 PM
|
Replies: 3
Views: 346
|
Forum: Model A (1928-31)
03-22-2024, 10:35 AM
|
Replies: 3
Views: 346
Torque Tube Grease Seal Direction for Install
Hi All,
I need to install a new grease seal in the torque tube and I am not sure which side of the seal faces downward when installing. The old seal that was removed was in bad shape and I could not...
|
Forum: Model A (1928-31)
02-22-2024, 11:32 PM
|
Replies: 5
Views: 598
|
Forum: Model A (1928-31)
02-22-2024, 09:11 AM
|
Replies: 5
Views: 598
|
Forum: Model A (1928-31)
02-21-2024, 10:12 PM
|
Replies: 5
Views: 598
Rear End Rebuild Advice/Help Needed
Hi All,
I am attempting my first rear end rebuild using Tom Endy’s articles for reference. All parts have been cleaned. I have all new seals, bearings and races installed. I also have a new 3.54...
|
Forum: Model A (1928-31)
08-18-2022, 12:06 AM
|
Replies: 46
Views: 14,164
|
Forum: Model A (1928-31)
05-09-2022, 09:37 PM
|
Replies: 2
Views: 484
|
Forum: Model A (1928-31)
05-09-2022, 12:28 PM
|
Replies: 2
Views: 484
Rear Fender Bolt/Nut Size for Wide Bed
Hi All,
I am looking for the correct bolt/nut size for a wide bed rear fender. The studs are in the bed and I have tried a 5/16-18 and a 5/16-24 nut but neither worked.
Thanks,
Denny
|
Forum: Model A (1928-31)
03-08-2022, 02:14 PM
|
Replies: 15
Views: 1,444
|
Forum: Model A (1928-31)
03-07-2022, 05:57 PM
|
Replies: 15
Views: 1,444
|
Forum: Model A (1928-31)
03-06-2022, 07:42 PM
|
Replies: 15
Views: 1,444
|
Forum: Model A (1928-31)
03-06-2022, 06:15 PM
|
Replies: 15
Views: 1,444
|
Forum: Model A (1928-31)
03-06-2022, 05:55 PM
|
Replies: 15
Views: 1,444
|
Forum: Model A (1928-31)
03-06-2022, 05:43 PM
|
Replies: 15
Views: 1,444
|
Forum: Model A (1928-31)
10-27-2021, 07:53 PM
|
Replies: 6
Views: 993
|
Forum: Model A (1928-31)
10-04-2021, 09:38 AM
|
Replies: 6
Views: 993
55th Annual SFV Model A Swap Meet/Car show
55th Annual San Fernando Valley Model A Swap Meet/Car show November 7th. Flyer attached with information of location and vendor/car entries. If this type of post is not allowed in this forum please...
|
Forum: Model A (1928-31)
09-14-2021, 03:48 PM
|
Replies: 33
Views: 4,061
Re: Clutch Issue - Need Help Please
Finally got it off with a little more hammering and some prying. I am wondering how this happened also. After I had drove it and then parked it for the long duration it was stored inside a shop until...
|
Forum: Model A (1928-31)
09-14-2021, 02:42 PM
|
Replies: 33
Views: 4,061
Re: Clutch Issue - Need Help Please
Finally had a change to pull the engine and transmission. The clutch disc is completely stuck. I tried to loosen it up by using a rubber mallet but that did nothing. Any ideas of how to remove this?...
|
Forum: Model A (1928-31)
07-08-2021, 09:32 PM
|
Replies: 33
Views: 4,061
Re: Clutch Issue - Need Help Please
@redmodelt - there is about 1 1/4” pedal travel
I will be checking the clutch arm tomorrow and also give the “Herky-Jerky” method one last shot. If that does not work then I will be pulling the...
|
Forum: Model A (1928-31)
07-07-2021, 01:58 PM
|
Replies: 33
Views: 4,061
Re: Clutch Issue - Need Help Please
@nkaminar - please see my video in the initial post. I opened the plate to show what is going on inside. I have not tried rocked the car back and forth yet.
Denny
|
Forum: Model A (1928-31)
07-07-2021, 01:20 PM
|
Replies: 33
Views: 4,061
Re: Clutch Issue - Need Help Please
Hi All,
Update - I warmed the engine and transmission up in neutral. Then turned the power off, clutch pressed to the floor and in 3rd gear, then bump the starter a few times. Also tried this in 1st...
|
Forum: Model A (1928-31)
07-07-2021, 07:50 AM
|
Replies: 33
Views: 4,061
|
Forum: Model A (1928-31)
07-06-2021, 08:40 PM
|
Replies: 33
Views: 4,061
Clutch Issue - Need Help Please
Hi All,
I parked my 31 pickup 8 months ago in the shop and everything was working just great. It has not been started since until today. The pickup fired right up. But now I am unable to put the car...
|
Forum: Model A (1928-31)
05-09-2021, 09:27 AM
|
Replies: 5
Views: 837
Re: Wide Bed Replacement Part Available ?
Thanks everyone.
@ Oldbluoval - I checked Mack Products and they do make this part. Thanks
http://mack-products.com/shop/products/crossmembers/1931-wide-bed-crossmember-rear/
Denny
|
Forum: Model A (1928-31)
05-08-2021, 09:15 PM
|
Replies: 5
Views: 837
Wide Bed Replacement Part Available ?
Hi All,
Does anyone make the rear bar for a wide bed that the tail gate brackets and stake pocket attaches too? I only see it available for a narrow bed.
Thanks,
Denny
|