Forum: Early V8 (1932-53)
01-07-2018, 07:02 PM
|
Replies: 18
Views: 3,129
|
Forum: Early V8
01-06-2018, 06:03 PM
|
Replies: 0
Views: 880
1934 closed car windshield post section
I am trying to un-chop a 1934 Ford closed car and need about 6 inches of windshield post to do the job. I have all the material for the door posts and top.
Any leads appreciated.
-Thank you
|
Forum: Early V8 (1932-53)
12-10-2017, 04:55 PM
|
Replies: 0
Views: 598
|
Forum: Early V8 (1932-53)
12-09-2017, 11:04 PM
|
Replies: 5
Views: 1,558
Re: Shipping a flathead
I used engine shippers.com.for a motor I purchased from Walt Dupont in Maine.
It was a few years ago but it cost 250.00 from Maine to Calif.
|
Forum: Early V8
12-08-2017, 01:39 AM
|
Replies: 2
Views: 1,305
|
Forum: Early V8
11-25-2017, 01:37 PM
|
Replies: 2
Views: 1,305
|
Forum: Early V8 (1932-53)
11-24-2017, 12:15 PM
|
Replies: 50
Views: 8,463
Re: Bob Drake sale
I tried to get '34 running boards, OUT OF STOCK
I tried to get a '34 grille OUT OF STOCK
I saved a lot more than 15% today !!
|
Forum: Early V8 (1932-53)
11-16-2017, 02:09 PM
|
Replies: 8
Views: 1,357
|
Forum: Early V8 (1932-53)
11-14-2017, 05:31 PM
|
Replies: 3
Views: 1,281
Does anyone reproduce '34 header panels ?
I am looking for a good '34 header panel.
Most of the '34 header panels I see for sale have rust issues.
I would think that someone has to be stamping these out by now.
Are any being repopped ?...
|
Forum: Model A (1928-31)
11-13-2017, 08:42 PM
|
Replies: 20
Views: 3,730
Re: Fastenal Shipping
Well, you did better than I did.
When I inquired about shipping at Fastenal they told me that in California they do not do freight shipments. I was a trying to ship an engine from the midwest to...
|
Forum: Early V8 (1932-53)
11-12-2017, 09:07 PM
|
Replies: 20
Views: 6,960
Re: 40 Ford Rear Axle Grease Seals
I have 6 of the seals left over from my convertible days.
I used 2 of them until I was able to tear into the rear axle.
The stopped the leak.
|
Forum: Early V8
11-08-2017, 02:21 PM
|
Replies: 2
Views: 1,305
|
Forum: Early V8 (1932-53)
11-08-2017, 12:28 AM
|
Replies: 3
Views: 902
Re: '34 sedan and Victoria fenders
From what I was able to understand there is an oblong hole at the inner edge of the rear fender. It is not visible when the fender is mounted. I was told it is for the fuel filler pipe.
|
Forum: Early V8 (1932-53)
11-07-2017, 10:49 PM
|
Replies: 3
Views: 902
'34 sedan and Victoria fenders
I read where '34 sedan and Victoria rear fenders the same except for the lack of a hole in the fender for the fuel filler in the Victoria ?
Can anyone verify this ?
|
Forum: Early V8
11-07-2017, 07:43 PM
|
Replies: 0
Views: 970
|
Forum: Early V8 (1932-53)
10-31-2017, 05:03 PM
|
Replies: 18
Views: 2,878
Re: 33 ford with muncie
There was a munce M-21 in my 5-W coupe when I purchased it in the early '70's. It really made the car a blast to drive but it was not installed correctly. The crossmember was really butchered up to...
|
Forum: Early V8 (1932-53)
10-31-2017, 04:58 PM
|
Replies: 30
Views: 7,784
|
Forum: Early V8
10-31-2017, 04:11 PM
|
Replies: 0
Views: 1,015
1934 Ford project body
I am looking for a '34 project car.
I have a lot of extra sheet metal and parts from previous projects and would like to put them to good use.
I am looking to see what might be out there for sale....
|