Forum: Model A (1928-31)
02-27-2018, 10:50 PM
|
|
Replies: 12
Views: 1,599
Re: Transmission tower question
Buy the tool. Bratton's has them as do others. I just did one with the tool and it went sweet. The first time I did one was with screwdrivers, clamps and a few band-aids. My levers, dash , shift...
|
|
Forum: Model A (1928-31)
02-27-2018, 10:32 PM
|
|
Replies: 29
Views: 4,260
Re: Engine install
I did two piece. The engine went in sweet with alignment studs in the bell and on a jack. All checks and shims in place. From engine back to the ujoint it got the full monty . New ring gear, clutch,...
|
|
Forum: Model A (1928-31)
02-23-2018, 07:53 PM
|
|
Replies: 29
Views: 4,260
Re: Engine install
The engine and new transmission is in and happy. Thanks to all for your help. The alignment studs worked great.
|
|
Forum: Model A (1928-31)
02-22-2018, 07:58 PM
|
|
Replies: 29
Views: 4,260
Re: Engine install
I am doing it two parts with the guide studs after I pack the U joint. I am also 73 and I got the car in 1960.
|
|
Forum: Model A (1928-31)
02-22-2018, 07:49 PM
|
|
Replies: 19
Views: 5,231
Re: Wishbone ball
My radius ball measured 1.479. I have been using the original style so maybe I will add the washer and see how the bolts tighten up.
|
|
Forum: Model A (1928-31)
02-22-2018, 03:48 PM
|
|
Replies: 29
Views: 4,260
Re: Engine install
Are you sure on 11/16? The books I have say 5/8", Les Andrews, vol 1, pg 1-148, the info sheet that came with the rebuild pressure plate, and the gauge to check them from Bratton's, all 5/8".
|
|
Forum: Model A (1928-31)
02-22-2018, 12:06 PM
|
|
Replies: 19
Views: 5,231
Re: Wishbone ball
What is the spec diameter for the original ball? Be a good thing to know so you know what needs to be done, other than that you are guessing.
|
|
Forum: Model A (1928-31)
02-22-2018, 10:34 AM
|
|
Replies: 29
Views: 4,260
Re: Engine install
NO, I am NOT pulling the body off to put the engine in. I do have them both out to change the transmission to the new synchronized one from Michell and change the clutch/pressure plate plus a new...
|
|
Forum: Model A (1928-31)
02-22-2018, 10:17 AM
|
|
Replies: 39
Views: 9,362
Re: 6V Quartz Halogen Headlight Question
http://www.classicandvintagebulbs.com/page3.html
I run them with a hi output 6v alternator from nu-rex and new reflectors from Bratton's. The light output is as bright as sealed beams or better.
|
|
Forum: Model A (1928-31)
02-22-2018, 09:32 AM
|
|
Replies: 29
Views: 4,260
Engine install
What is the best way to reinstall the engine/transmission. Trans/ bell housing first then engine or engine/ transmission as a unit?
|
|
Forum: Model A (1928-31)
02-18-2018, 07:59 AM
|
|
Replies: 3
Views: 1,077
Oil pump shield
How can I tell if I have '31 Pan? What measurement tells me? Is it possible to trim the shield ?
|
|
Forum: Model A (1928-31)
02-10-2018, 04:41 PM
|
|
Replies: 96
Views: 18,585
|
|
Forum: Model A (1928-31)
02-10-2018, 04:40 PM
|
|
Replies: 22
Views: 5,525
|
|
Forum: Model A (1928-31)
02-10-2018, 03:38 PM
|
|
Replies: 22
Views: 5,525
Re: Flywheel Tool?
There is a tool made to turn the engine over using the ring gear. It was a long bar with a swinging curved hook.
|
|
Forum: Model A (1928-31)
02-10-2018, 03:31 PM
|
|
Replies: 96
Views: 18,585
|
|
Forum: Model A (1928-31)
02-09-2018, 09:22 PM
|
|
Replies: 16
Views: 2,562
|
|
Forum: Model A (1928-31)
02-09-2018, 08:41 PM
|
|
Replies: 16
Views: 2,562
A shock (ing) question
What would be the best for touring in a 1931 Tudor, modern shock kit or new original style like Bratton sells? Which will make the ride the best? I have had the car since 1960, time to make it as...
|
|
Forum: Model A (1928-31)
05-16-2016, 07:15 PM
|
|
Replies: 6
Views: 3,263
|
|
Forum: Model A (1928-31)
05-16-2016, 06:57 PM
|
|
Replies: 6
Views: 3,263
|
|
Forum: Model A (1928-31)
12-23-2015, 10:32 AM
|
|
Replies: 43
Views: 7,416
Re: How long has she been "Your Baby"?
I got my 1931 Tudor in 1960. My farther, Robert, bought it for me for my 16th birthday. Cost him
$115 and is the best birthday gift I ever got, Thanks Dad.
|
|
Forum: Model A (1928-31)
12-23-2015, 10:21 AM
|
|
Replies: 22
Views: 6,276
|
|
Forum: Model A (1928-31)
12-09-2015, 03:13 PM
|
|
Replies: 22
Views: 6,276
LED tail lights with turn signals? A fix needed
I just installed R and L LED tail light assembles and find that I can not use them as turn signals as I have in the past with the old double contact incandescent tail lights . Because the LED...
|
|
Forum: Model A (1928-31)
08-22-2015, 02:57 PM
|
|
Replies: 10
Views: 2,901
|
|
Forum: Model A (1928-31)
08-22-2015, 02:55 PM
|
|
Replies: 10
Views: 2,901
|
|
Forum: Model A (1928-31)
08-22-2015, 02:43 PM
|
|
Replies: 10
Views: 2,901
Engine slows when #1 is hooked up
The problem is as follows. 1929 with lots of miles still running with original wiring. Engine at idle, spark up, remove #1 spark plug connector from the distributor and the engine speeds up , make...
|
