Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.13 seconds.
Search: Posts Made By: Mac VP
Forum: Early V8 (1932-53) 10-21-2021, 07:44 AM
Replies: 5
Views: 315
Posted By Mac VP
Re: Adjustable throttle rod

We stock an original Ford adjustable throttle rod…….goes from 11-7/8” to 12-7/8”……and has the spring loaded ends. I have included the picture link here.
...
Forum: Early V8 (1932-53) 10-12-2021, 04:30 AM
Replies: 26
Views: 1,126
Posted By Mac VP
Re: 59AB advice on "new" flathead

A wise mechanic also drilled the 1/8” holes in each lifter boss. Obviously, this should be done during the block prepping stage so that the waste chips can be cleaned out prior to motor assembly. Now...
Forum: Early V8 (1932-53) 10-05-2021, 06:21 AM
Replies: 5
Views: 241
Posted By Mac VP
Re: 8BA Starter bolts

We have them as well
Forum: Early V8 (1932-53) 10-03-2021, 03:11 PM
Replies: 6
Views: 435
Posted By Mac VP
Re: Lincoln clusters?

I took a quick look at my gear catalogs and couldn’t find the match. One thing I can say…..it’s NOT a Lincoln Zephyr gear from the 1940-48 era. The diamond shaped first gear teeth are definitely 1949...
Forum: Early V8 (1932-53) 10-01-2021, 05:43 AM
Replies: 7
Views: 423
Posted By Mac VP
Re: clutch chatter

Here’s a list of possible causes and remedies for the clutch problem.

http://www.vanpeltsales.com/FH_web/flathead_clutchchatter-troubleshoot.htm
Forum: Early V8 (1932-53) 09-14-2021, 05:47 AM
Replies: 10
Views: 846
Posted By Mac VP
Re: Van Pelts?

We were closed for a much needed week of vacation a couple weeks ago. COVID has boosted the number of phone calls and orders over the last year and a half. Not just for us but for all the vintage car...
Forum: Early V8 (1932-53) 09-11-2021, 07:05 AM
Replies: 5
Views: 409
Posted By Mac VP
Re: 4 Speed Leak Situation

Those shafts have a “push fit” as you slide them into the case from the rear, until you get to the last 1/2” inch or so. The shafts were machined with a slightly bigger diameter on the rear end so...
Forum: Early V8 (1932-53) 09-06-2021, 05:35 AM
Replies: 32
Views: 1,058
Posted By Mac VP
Re: 1936 Ford 1.5 ton 4 speed Transmission jumps out of 4th gear

Ford (and later on Borg Warner) never made or offered any alternate gears for those transmissions. The only gears ever made for that gearbox were the same from 1932-52 when they stopped making the...
Forum: Early V8 (1932-53) 08-24-2021, 05:06 AM
Replies: 10
Views: 671
Posted By Mac VP
Re: Help Identifying a Transmission.

Yes, of course that is very true. The photo was of the Sideloader version so my identification remarks were based on that. The toploader version existed from 1942-52. The sideloader version of the...
Forum: Early V8 (1932-53) 08-23-2021, 05:05 AM
Replies: 10
Views: 671
Posted By Mac VP
Re: Help Identifying a Transmission.

I think they may have begun offering the column shifter in 1950 models but the pickup truck experts can confirm that. The Ford F-1 pickup line ran from 1948 through 1952. The open drive Toploader...
Forum: Early V8 (1932-53) 08-15-2021, 08:26 PM
Replies: 8
Views: 528
Posted By Mac VP
Re: Shoe Box OD Transmission

49-50 Ford OD transmissions in the convertible carried a modified mount for the overdrive solenoid. When Ford moved the rear support forward for 1951 the overall modification allowed them to...
Forum: Early V8 (1932-53) 08-15-2021, 05:15 AM
Replies: 8
Views: 528
Posted By Mac VP
Re: Shoe Box OD Transmission

The rear support mounting flange moved forward for 1951 and the spacing for the two bolt holes opened up a bit to an even 6” center to center. The overall length of the 49-51 transmissions remained...
Forum: Early V8 (1932-53) 07-25-2021, 04:52 AM
Replies: 5
Views: 520
Posted By Mac VP
Re: Shoebox Overdrive Governors

Except for the early Lincoln overdrives (1940-48) all of the Ford based Borg Warner OD governors used the single terminal governor unit. I don’t know exactly what year the change occurred but they...
Forum: Early V8 (1932-53) 07-21-2021, 05:48 AM
Replies: 39
Views: 2,399
Posted By Mac VP
Re: I'm a turncoat...

The Hornet is absolutely beautiful! I own one of its later descendants (OT 73 hatchback). Your new set of wheels is just stunning.
Forum: Early V8 (1932-53) 07-18-2021, 01:30 PM
Replies: 12
Views: 874
Posted By Mac VP
Re: Speedo drive gear

Do you have the B-17290 thrust washer fitted in there between the roller bearing and the speedo gear?
Forum: Early V8 (1932-53) 07-15-2021, 05:40 AM
Replies: 4
Views: 254
Posted By Mac VP
Re: 49 wagon clutch size

They would have had the regular 9.5” clutch but 10” was optional. In either case, both had the 1” x 10 spline hub in the disc. They never came with an 11” clutch……that would have been overkill, and...
Forum: Early V8 (1932-53) 07-13-2021, 05:53 AM
Replies: 49
Views: 1,455
Posted By Mac VP
Re: 1933 transmission tower plunger

Frank, we have the instructions for putting the shifter forks into neutral…..and for setting the gears into neutral……on our website. The first link is for setting the shifter forks & rails. The...
Forum: Early V8 (1932-53) 07-12-2021, 04:08 AM
Replies: 3
Views: 275
Posted By Mac VP
Re: 49 trans.

There’s no difference and they are totally interchangeable. The 49-50 convertibles used a special adapter for the solenoid to allow it to clear the frame but even the basic overdrive transmission is...
Forum: Early V8 (1932-53) 07-07-2021, 06:10 AM
Replies: 49
Views: 1,455
Posted By Mac VP
Re: 1933 transmission tower plunger

The plungers are hollow and their tips will wear…..sometimes all the way through. Your comment above makes me ask, what problem are you chasing that you’re hoping this question would help you resolve?
Forum: Early V8 (1932-53) 07-06-2021, 04:53 PM
Replies: 49
Views: 1,455
Posted By Mac VP
Re: 1933 transmission tower plunger

All 32-38 shifter housings used the single spring/two plungers detent system, and they’re located between the two shifter rails. The plug in the side of the housing is merely to provide an access...
Forum: Early V8 (1932-53) 07-05-2021, 06:54 AM
Replies: 11
Views: 547
Posted By Mac VP
Re: Identifying a 39 Tranny

This link will fill you in for most of the details:

http://www.vanpeltsales.com/FH_web/flathead_transID_3speed.htm
Forum: Early V8 06-27-2021, 06:52 PM
Replies: 0
Views: 238
Posted By Mac VP
39 Transmission with LZ gears - SOLD !

SOLD! A fresh rebuild from our shop. This has the 18-26 Lincoln Zephyr close ratio gearset and late style synchro assy in a closed drive 78 series case. Double detent 81A shifter housing. Unit...
Forum: Early V8 (1932-53) 06-21-2021, 05:26 PM
Replies: 6
Views: 525
Posted By Mac VP
Re: 1950 Ford Overdrive problem

I had one several years ago like that….. I had to take an abrasive cutoff wheel to it and cut it apart. That old Borg Warner steel is/was damn hard stuff.
Forum: Early V8 (1932-53) 06-21-2021, 05:28 AM
Replies: 6
Views: 525
Posted By Mac VP
Re: 1950 Ford Overdrive problem

I assume you were able to remove the outer housing by itself, with the output shaft and ring gear remaining in place at the back of the transmission. If so, normally you can simply pull it off with...
Forum: Early V8 (1932-53) 05-23-2021, 05:59 PM
Replies: 15
Views: 1,392
Posted By Mac VP
Re: Anything for a cluster gear

Usable transmission? Define that. A good used case, shifter tower with the forks you want, and all gears in good condition? I’d say more like 1 in 10 odds. Of course, we’re happy to end up with...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:37 AM.