Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 24 of 24
Search took 0.00 seconds.
Search: Posts Made By: azandy
Forum: Early V8 (1932-53) 12-11-2018, 07:17 AM
Replies: 3
Views: 430
Posted By azandy
Re: Replacing pinion seal 1950 Ford car

Wow! A great response, I'm not about to break into the rear end so I'll just replace the seal per your suggestions. It was not making noise so I think I'll be okay.
Thank you
Andy
Forum: Early V8 (1932-53) 12-10-2018, 05:54 PM
Replies: 3
Views: 430
Posted By azandy
Replacing pinion seal 1950 Ford car

I'm replacing the pinion seal on my 1950 Ford car. The drive shaft is out, the pinion nut, shaft and u-joint flange are marked and wheels are off the ground. When I rotate the u-joint flange by hand...
Forum: Early V8 (1932-53) 07-23-2018, 11:51 AM
Replies: 5
Views: 548
Posted By azandy
Re: Clutch linkage pivot ball

Thanks for the responses.
Andy
Forum: Early V8 (1932-53) 07-22-2018, 02:50 PM
Replies: 5
Views: 548
Posted By azandy
Question Clutch linkage pivot ball

Can anyone tell me, what is the diameter of the pivot ball for the clutch linkage on a 1940 - 1948 Ford car?
Thanks,
Andy
Forum: Model A (1928-31) 05-08-2018, 08:45 AM
Replies: 9
Views: 1,466
Posted By azandy
Steering wheel

It's getting hard to get my knees under the steering wheel and hit the pedals on my 30 Coupe. Does anybody have an idea on how to raise the steering wheel a couple inches, is there a kit available?...
Forum: Early V8 (1932-53) 12-17-2017, 11:33 AM
Replies: 0
Views: 356
Posted By azandy
Tremec T5 in a 1950 Ford car

I'm putting the Speedway Motors Tremec T5 trans conversion kit in a 1950 Ford car. Has anyone done this?
*What crossmember can be used? ( Jamco has one that works with a TH350 )
*How is the 1950...
Forum: Early V8 11-12-2017, 11:08 AM
Replies: 0
Views: 226
Posted By azandy
Question Wanted- 49-51 Ford car Bell Housing Adapter

I need the trans adapter for a 49-51 Ford car that will allow for the installation of a Tremec 5 speed transmission. It is 3 wide and I believe the part number is 8BA-6392. The 3" adapter will bolt...
Forum: Early V8 (1932-53) 06-15-2017, 04:28 PM
Replies: 5
Views: 995
Posted By azandy
49-50 & 51 Ford car Trans & Overdrive

Question - Are the transmission and overdrive assemblies (excluding internal parts) for the 49, 50 and 51 Ford car (not convertible) interchangeable?
Thanks for any input,
Azandy
Forum: Early V8 (1932-53) 06-09-2017, 04:53 PM
Replies: 0
Views: 276
Posted By azandy
russcc

I hope I'm not stretching the rules for this forum but I'm trying to get a message thru to russcc. Apparently your inbox is full and won't accept more messages. If you delete a few messages I can get...
Forum: Early V8 06-06-2017, 10:09 AM
Replies: 0
Views: 496
Posted By azandy
Wanted, 49 or 50 Ford car Overdrive or OD and Transmission

I'm looking for a 1949 or 1950 Ford car overdrive or the overdrive and transmission together. Thanks,
Azandy
Forum: Early V8 05-24-2017, 09:46 AM
Replies: 0
Views: 213
Posted By azandy
Wanted, Overdrive or Overdrive & Trans

I broke something in the overdrive unit in my 1950 Ford car (cracked the case). I'm looking to replace the overdrive unit or the od. and trans together.
Forum: Early V8 (1932-53) 05-15-2017, 12:22 PM
Replies: 2
Views: 387
Posted By azandy
Rear end side and pinion gears in a 1950 Ford car

There's as much as 1/8 inch of free axial movement in a couple of the small gears in the differential of my 1950 Ford car. Is this normal and if I need to tighten them up how can I do it without...
Forum: Early V8 (1932-53) 05-06-2017, 09:11 AM
Replies: 8
Views: 1,262
Posted By azandy
Re: 1950 Ford car rear end

Thanks for all the advice, I'll try some of these things. I did break an axle once and used a tube from household vacuum cleaner to get the thing out. I may look into a Maverick rear end. The thing I...
Forum: Early V8 (1932-53) 05-04-2017, 05:51 PM
Replies: 8
Views: 1,262
Posted By azandy
Question 1950 Ford car rear end

Something broke with a loud bang in the differential of my 50 Ford car. I've pulled the axles and taken out the housing bolts but I can't get the assembly out. Apparently what ever broke is...
Forum: Early V8 (1932-53) 04-11-2015, 06:37 PM
Replies: 10
Views: 1,314
Posted By azandy
Re: Transmission woes

Now that I've got everything apart I'm going to replace the synchro stuff. I had been using the wrong gear lube, gonna switch to GL1 and check clutch pedal play and shift linkage for wear. Thank you...
Forum: Early V8 (1932-53) 04-09-2015, 06:18 PM
Replies: 10
Views: 1,314
Posted By azandy
Re: Transmission woes

If it makes a difference, the car is a daily driver and it ran great for the last 5,ooo miles and then last week it started making noise.
Forum: Early V8 (1932-53) 04-09-2015, 01:42 PM
Replies: 10
Views: 1,314
Posted By azandy
Transmission woes

I have a 50 Ford car with a stock 3 speed overdrive transmission. It grinds trying to shift into 2nd gear. I've been told that the syncros are the problem. To me this stuff dosen't look too bad. I'm...
Forum: Early V8 (1932-53) 03-25-2015, 07:19 PM
Replies: 2
Views: 690
Posted By azandy
Second gear trouble.

I have a 1950 Ford car with a 3 speed transmission and overdrive. I can't get it into second gear, grinding and "Gnashing of Teeth". First and third gears are okay and the shift linkage seems fine.
...
Forum: Early V8 (1932-53) 05-09-2013, 10:38 AM
Replies: 3
Views: 1,050
Posted By azandy
Electrical problem solved !!

Thanks for all the responses concering my 50 ford that wouldn't turn off. It seems that while doing some rewireing I inadvertently (stupidly) cut the diode out of the DA plug wire. I thought it was a...
Forum: Early V8 (1932-53) 05-04-2013, 05:48 PM
Replies: 10
Views: 1,253
Posted By azandy
Electrical problem

I have a 1950 Ford car V8 converted to 12 volt neg ground with a Pertronix distributor conversion and a one wire alternator.
The car does not shut off unless I disconnect the alternator. The three...
Forum: Model A (1928-31) 03-23-2012, 07:55 AM
Replies: 9
Views: 1,179
Posted By azandy
Re: cowl lamp alignment

The three hole moveable plate inside the bucket was stuck with corrosion. I got it loose and now I see how to adjust it. I'll come up with something to replace the wood blocks. GOOD TIPS! Thanks,...
Forum: Model A (1928-31) 03-22-2012, 08:49 PM
Replies: 9
Views: 1,179
Posted By azandy
Re: cowl lamp alignment

No I don't. I can't see where the bolcks would fit on ihe outside of the body and the exterior surface determines ihe alignment of the bracket. I'll try loosening the three bucket screws abd see if...
Forum: Model A (1928-31) 03-22-2012, 06:17 PM
Replies: 9
Views: 1,179
Posted By azandy
cowl lamp alignment

Got a set of origional cowl lamps for my 1930 coupe. When I bolt them in they aren't aimed right. How do I align them? beveled washers?
Thanks for any advice.
Andy
Forum: Early V8 (1932-53) 08-15-2010, 01:38 PM
Replies: 4
Views: 927
Posted By azandy
Runs rough

My 50 Ford V8 ran good one day and then started running rough and hesitating.
What I've done:

Checked timing----OK
Checked fuel flow----OK
Checked compression----OK
Blanked off vacuum line...
Showing results 1 to 24 of 24

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 01:00 AM.