Go Back   The Ford Barn > Search Forums
Reload this Page Search Results

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 11 of 11
Search took 0.00 seconds. Search: Posts Made By: Barry53
Forum: Early V8 (1932-53) 01-06-2016, 03:53 AM
Replies: 23
Views: 5,183
Posted By Barry53
Re: Oil Pressure

Hopefully attached are picks of the pickup
Forum: Early V8 (1932-53) 01-06-2016, 03:31 AM
Replies: 23
Views: 5,183
Posted By Barry53
Re: Oil Pressure

As suggested hooked in a pressure gauge, the readings were approx at idle in the region of 10-15lbs, with a few revs on the pressure was in the region of 30-40lbs. Hard to be to accurate as the...
Forum: Early V8 (1932-53) 01-02-2016, 06:42 PM
Replies: 23
Views: 5,183
Posted By Barry53
Re: Oil Pressure

The oil being used is 20w/50. not sure what mileage the engine has done, brought it as is. Have had heads off, some wear in bores nothing major. Have just done a 180km(112miles) trip with no problem....
Forum: Early V8 (1932-53) 01-01-2016, 11:42 PM
Replies: 23
Views: 5,183
Posted By Barry53
Oil Pressure

I have finally got my 39 pickup on the road. It has a 81A engine. on start up from cold the oil pressure gauges reads about 15lbs, after warming up the pressure drops to about 5-10lbs then when hot...
Forum: Early V8 (1932-53) 04-21-2015, 05:27 PM
Replies: 2
Views: 1,052
Posted By Barry53
99A Block Crankshaft

I have a crankshaft from a 99A block can it be used in a 59A block. Also the rods from the 99A crankshaft can they also be used in the 59A block
Forum: Early V8 (1932-53) 02-12-2014, 06:58 PM
Replies: 2
Views: 1,128
Posted By Barry53
1939 Pickup Window Channel

In the procees of installing Windows in my 39 Pickup. I have a window channel Kit. For the side of the door there is 4 channels, now the 2 wider one do they go the front of the door. Why I ask...
Forum: Early V8 (1932-53) 12-02-2013, 03:56 PM
Replies: 2
Views: 1,061
Posted By Barry53
1939 Pickup Windows

I am putting the felt window channels in a 39 Pickup. Whats hold in the felt channel around the top of the door. I have in the kit supplied some small screws about 25 not sure where they go. The push...
Forum: Early V8 (1932-53) 12-19-2012, 03:29 PM
Replies: 6
Views: 1,499
Posted By Barry53
Re: 1939 Pickup Gauges

Reason I asked about the gauges is that I am in the process of rewing the pickup with help, Would the battery level/voltmeter gauge be wired in differently from the ammeter. It looks like a ammeter...
Forum: Early V8 (1932-53) 12-17-2012, 06:35 PM
Replies: 6
Views: 1,499
Posted By Barry53
1939 Pickup Gauges

The set of gauges for my 39 pickup has a battery level indicator(H,N,L) I have seen a amp gauge for a 39 with the level of charge. What gauge should the 39 pickup have (batt or Amp). Presumely the...
Forum: Early V8 (1932-53) 11-19-2012, 04:44 PM
Replies: 4
Views: 2,549
Posted By Barry53
Re: 1939 ford pickup hood hinges

Thanks there is a gap between hood and cowl with hinges up the other way. With the right angle peice on the bottom it sits on the cowl alright but there is a gap between side panel and hood probably...
Forum: Early V8 (1932-53) 11-19-2012, 03:46 PM
Replies: 4
Views: 2,549
Posted By Barry53
1939 ford pickup hood hinges

I am putting back together a 39 ford pickup, on it the hood hinges are triangle shaped with two bolt holes at the front and one at the back. At the front of the hinge is a right angle piece with a...
Showing results 1 to 11 of 11

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 11:53 AM.