Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.03 seconds.
Search: Posts Made By: Drive Shaft Dave
Forum: Model A (1928-31) 10-26-2019, 11:06 PM
Replies: 19
Views: 678
Posted By Drive Shaft Dave
Re: Pan Gasket

looks good on paper, let us know the outcome.
Forum: Model A (1928-31) 10-05-2019, 11:15 PM
Replies: 13
Views: 949
Posted By Drive Shaft Dave
Re: New Two Blade Fan

Dont forget to use a thin flat washer under the shaft nut.
Forum: Model A (1928-31) 10-03-2019, 11:18 PM
Replies: 6
Views: 450
Posted By Drive Shaft Dave
Re: Tricks to remove cutout cover?

The idea is to break the spot welds there are usually two.
Forum: Model A (1928-31) 08-22-2019, 10:58 PM
Replies: 18
Views: 932
Posted By Drive Shaft Dave
Re: Motor Suddenly Stuck

This is one of those times when a block of wood and a very large whammer is your friend
...
Forum: Model A (1928-31) 08-17-2019, 11:07 PM
Replies: 14
Views: 675
Posted By Drive Shaft Dave
Re: New clutch - should the throw out bearing disengage?

Yes, if you are pushing the clutch pedal to the floor it will spin. how close is the throw out bearing when the pedal is released?
Forum: Model A (1928-31) 05-29-2019, 09:45 PM
Replies: 3
Views: 402
Posted By Drive Shaft Dave
Re: rear brake single shoe ,emerg brake history

In the case of the ModelA,the revised rear brakes came with a stepped drum to accomodate the emergency brake band. The early models simply picked up the service brake with the hand brake lever. As...
Forum: Model A (1928-31) 03-30-2019, 01:52 AM
Replies: 32
Views: 2,064
Posted By Drive Shaft Dave
Re: How much grease in the clamshell?

I just remove one of the bolts.
Forum: Model A (1928-31) 03-19-2019, 01:44 AM
Replies: 8
Views: 610
Posted By Drive Shaft Dave
Re: Trunk floor pan

The same part is used for both configurations.
Forum: Model A (1928-31) 02-27-2019, 01:31 AM
Replies: 10
Views: 1,116
Posted By Drive Shaft Dave
Re: Rear Hub Grease Seal Removal Tool

I have used the Tom Endy method for years , works good.
Forum: Model A (1928-31) 02-27-2019, 01:24 AM
Replies: 5
Views: 480
Posted By Drive Shaft Dave
Re: 31 Coupe Wood (Under side window)

upholstery panel nails to this.
Forum: Early V8 (1932-53) 02-02-2019, 08:34 PM
Replies: 11
Views: 1,029
Posted By Drive Shaft Dave
Re: What is this puller part for ???

The puller is used to remove rear drums and hub from tapered axle shafts. I didn't read the compete thread . I dont know what the other part is. Tried to delete but wouldn't take.
Forum: Model A (1928-31) 02-02-2019, 08:30 PM
Replies: 54
Views: 4,949
Posted By Drive Shaft Dave
Re: Ford Tri-Motor

Actually the Harvard was a different airplane, although a trainer with fixed gear.
Forum: Model A (1928-31) 02-01-2019, 09:10 PM
Replies: 12
Views: 960
Posted By Drive Shaft Dave
Re: Engine mount rubber replacement

Brattons cataloge pg. 35, 2018, shows motor mount rubbers made to the Ford print. while I have not tried these, the last mount 's I put in , made use of some dish soap and they slid in quite...
Forum: Model A (1928-31) 01-14-2019, 12:14 AM
Replies: 2
Views: 405
Posted By Drive Shaft Dave
Forum: Model A (1928-31) 01-07-2019, 12:24 AM
Replies: 42
Views: 2,871
Posted By Drive Shaft Dave
Re: Water Temperature Gauge

I have heard that the rex aco temp gauge has been problematic in the last few years .
Forum: Model A (1928-31) 01-07-2019, 12:09 AM
Replies: 8
Views: 1,716
Posted By Drive Shaft Dave
Re: Tom Wesenberg

Yes he is ok. just taking a look around the country side.
Forum: Model A (1928-31) 12-07-2018, 08:11 PM
Replies: 1
Views: 361
Posted By Drive Shaft Dave
Re: Need clarification...Bolts and Toggle Lever...

fine thread on the Spring Bolts, Toggle lever , drive in.
Forum: Model A (1928-31) 12-06-2018, 11:20 PM
Replies: 56
Views: 3,912
Posted By Drive Shaft Dave
Re: Weld and grind roller tracks

It is more of a hassle to replace them , weld then file or use die grinder.
Forum: Model A (1928-31) 12-02-2018, 01:54 AM
Replies: 11
Views: 1,250
Posted By Drive Shaft Dave
Re: 7.0 Earthquake in Anchorage Alaska

Alaska had a bad one in 1964 I remember. Was 9.2 on the Richter scale.
Forum: Model A (1928-31) 11-28-2018, 12:32 AM
Replies: 5
Views: 738
Posted By Drive Shaft Dave
Re: Tail pipe stub

Muffler shop could make one.
Forum: Model A (1928-31) 11-28-2018, 12:30 AM
Replies: 57
Views: 5,014
Posted By Drive Shaft Dave
Re: Stroke

Hang in there Bill!
Forum: Model A (1928-31) 10-18-2018, 10:10 PM
Replies: 8
Views: 807
Posted By Drive Shaft Dave
Re: Ignition switch

Disconnect the light and horn wire from the cut out then try it, you most likely have socket grounded .
Forum: Model A (1928-31) 09-21-2018, 01:16 PM
Replies: 23
Views: 2,493
Posted By Drive Shaft Dave
Re: coils question

How about Chev 6 cyl. they were always mounted terminals down.
Forum: Model A (1928-31) 09-21-2018, 12:26 AM
Replies: 18
Views: 1,582
Posted By Drive Shaft Dave
Re: Fan Blade advice.

make shure you use a flat steel washer under the mounting nut on an aluminum fan.
Forum: Model A (1928-31) 09-21-2018, 12:12 AM
Replies: 15
Views: 1,551
Posted By Drive Shaft Dave
Re: Another Gas Tank and Headlight question

If you put in sealer there will come a day you wish you hadn't.
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:32 PM.