Forum: Early V8
04-04-2015, 01:50 AM
|
Replies: 0
Views: 829
33-34 decklid
Looking for a decklid... Any condition considered.... Thanks
|
Forum: Early V8 (1932-53)
04-02-2015, 11:36 PM
|
Replies: 21
Views: 5,515
Re: 21 stud hot rod motor?
Just looking at your placement of axle compared to grill , I'm going to try a few. Inches lower just curious where the tie rod lands in relation to the frame or I may have to do a clearance bump or...
|
Forum: Early V8 (1932-53)
03-29-2015, 06:48 PM
|
Replies: 5
Views: 1,440
Re: Steering box Id?
I think you should still be able to fish the horn rod through the cover ? Then you need the 2 bolt clip that attaches the switch
|
Forum: Early V8 (1932-53)
03-29-2015, 05:42 PM
|
Replies: 0
Views: 1,124
What are the best headgaskets ?
I need to pull the heads off my big 59a with offenhauser heads , a friend was over and asked why I used the copper gaskets... I really didnt have an answer other than I used to work for an old...
|
Forum: Late V8
03-29-2015, 01:47 PM
|
Replies: 1
Views: 953
|
Forum: Late V8
03-29-2015, 01:46 PM
|
Replies: 1
Views: 953
Y block rockers
Pulled off of a rebuilt 312 that swallowed water and had to scrap
Questions? Call/text 651-336-0522
|
Forum: Late V8
03-29-2015, 01:43 PM
|
Replies: 3
Views: 1,315
|
Forum: Late V8
03-29-2015, 01:40 PM
|
Replies: 3
Views: 1,315
|
Forum: Late V8
03-29-2015, 01:38 PM
|
Replies: 3
Views: 1,315
|
Forum: Late V8
03-29-2015, 01:36 PM
|
Replies: 3
Views: 1,315
Y block 312 exhaust manifolds
Pulled these off a 312 I scrapped one has a casting # edb-9430-a i believe is thunderbird and the other does not... The one that does not have #s also has a repaired ear that was broken ( amateur...
|
Forum: Early V8 (1932-53)
03-28-2015, 12:28 PM
|
Replies: 21
Views: 5,515
Re: 21 stud hot rod motor?
Thanks for all the imput guys ..
.. That's a NICE little 32 truck Gavin...I like it... Thinking about doing front suspension in similar fashion , with a dropped axle on mine... Could I get pics of...
|
Forum: Early V8 (1932-53)
03-23-2015, 12:07 AM
|
Replies: 21
Views: 5,515
Re: 21 stud hot rod motor?
Yes , I'm sure there was, I was just curious what one could expect from a "small flat motor" , I'm not well versed in all things flat but , but have experianced those two bigger flat motors a ...
|
Forum: Early V8 (1932-53)
03-22-2015, 09:16 PM
|
Replies: 21
Views: 5,515
Re: 21 stud hot rod motor?
Sounds good Walt ... I was thinking a 4" merc crank , some port work and maybe a 400jr cam or equivalent ? I actually found a post on the hamb saying the LB blocks won't take too much bore... I...
|
Forum: Early V8 (1932-53)
03-22-2015, 07:56 PM
|
Replies: 21
Views: 5,515
21 stud hot rod motor?
Hey guys , I tried to do a search but couldn't get it to work... I have had a couple later hotrod flat motors one was a 53 merc bored 3 5/16 with mild port and 400 jr. And the other is a 3 3/8x 4 1/8...
|
Forum: Early V8
01-10-2011, 12:33 AM
|
Replies: 0
Views: 1,344
|
Forum: Early V8
01-10-2011, 12:26 AM
|
Replies: 1
Views: 1,333
|
Forum: Early V8
01-10-2011, 12:17 AM
|
Replies: 0
Views: 1,237
|