Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 35
Search took 0.01 seconds.
Search: Posts Made By: fortyman
Forum: Early V8 (1932-53) 03-28-2023, 09:42 PM
Replies: 7
Views: 1,077
Posted By fortyman
Re: 1940 Carburetor

Thanks for the response. The one on mine has the number 92 on it.
Forum: Early V8 (1932-53) 03-28-2023, 07:04 PM
Replies: 7
Views: 1,077
Posted By fortyman
1940 Carburetor

What is the correct carburetor for a 1940 flathead v8?
Forum: Early V8 (1932-53) 03-28-2023, 06:53 AM
Replies: 4
Views: 519
Posted By fortyman
Cooling Fan

Any recommendations on installing an electric fan to help with overheating on 1940 flathead. Would a fan help and if so what should I use?
Forum: Early V8 (1932-53) 11-16-2022, 10:15 PM
Replies: 23
Views: 3,032
Posted By fortyman
Re: Coolant leak at Heat Exchanger

I have not. I did look at the oil dipstick and it is whitish.
Forum: Early V8 (1932-53) 11-15-2022, 08:42 PM
Replies: 23
Views: 3,032
Posted By fortyman
Re: Coolant leak at Heat Exchanger

No stains or signs of leaking anywhere else.
Forum: Early V8 (1932-53) 11-15-2022, 06:19 PM
Replies: 23
Views: 3,032
Posted By fortyman
Re: Coolant leak at Heat Exchanger

Pic of what is leaking under car

503353
Forum: Early V8 (1932-53) 11-12-2022, 03:37 PM
Replies: 23
Views: 3,032
Posted By fortyman
Re: Coolant leak at Heat Exchanger

I will run it some to see. Have not tried that.
Forum: Early V8 (1932-53) 11-12-2022, 12:01 PM
Replies: 23
Views: 3,032
Posted By fortyman
Re: Coolant leak at Heat Exchanger

Just figured out how to post picture. The liquid comes out the area where it looks like a slit in the heat exchanger unit that goes into the crossover pipe. I can't recall if the crossover pipe was...
Forum: Early V8 (1932-53) 11-12-2022, 11:56 AM
Replies: 23
Views: 3,032
Posted By fortyman
Forum: Early V8 (1932-53) 11-11-2022, 10:14 PM
Replies: 23
Views: 3,032
Posted By fortyman
Coolant leak at Heat Exchanger

What would cause coolant to leak from where the heat exchanger ties in to the crossover pipe on a flathead v8?
Forum: Early V8 (1932-53) 07-21-2022, 12:48 PM
Replies: 2
Views: 544
Posted By fortyman
1940 part identification

Anyone know what this is and where it goes. Came off a 1940 Ford Deluxe. Very thin and less than 3 inches long.
Forum: Early V8 (1932-53) 06-10-2022, 10:06 PM
Replies: 8
Views: 852
Posted By fortyman
Identify 1940 ford part

Can someone identify the part in the attached picture. Where does it go?[AT491680
Forum: Early V8 (1932-53) 05-26-2021, 07:40 PM
Replies: 2
Views: 684
Posted By fortyman
1940 deluxe fordor window regulator

I replaced window channels and felt on front doors. Window rolled up and down just fine until I installed door panel and garnish moulding. The glass now comes out of channel when I roll the window...
Forum: Early V8 (1932-53) 03-01-2021, 10:40 AM
Replies: 2
Views: 533
Posted By fortyman
Front Bumper Grommets

The front bumper grommets for 1940 Ford Fordor. One side of the grommet is wider. Does the wide side go toward the inside or outside?
Forum: Early V8 (1932-53) 02-05-2021, 10:16 AM
Replies: 2
Views: 759
Posted By fortyman
1940 fordor door handle

There is a small gap on one side between the exterior door handle base to the car. The 1940 ford fordor door handles have a screw in the threaded hole in the handle base. When I tighten the screw it...
Forum: Early V8 (1932-53) 03-18-2020, 05:49 PM
Replies: 4
Views: 916
Posted By fortyman
Re: 40 ford fordoor. Still need help with rear armrest

Anyone know where one could get the formed piece?
Forum: Early V8 (1932-53) 03-09-2020, 04:26 PM
Replies: 8
Views: 1,261
Posted By fortyman
Re: 1940 ford deluxe windows

Okay. Thanks. So does the front go all the way down?
Forum: Early V8 (1932-53) 03-09-2020, 09:55 AM
Replies: 8
Views: 1,261
Posted By fortyman
Forum: Early V8 (1932-53) 03-08-2020, 05:04 PM
Replies: 8
Views: 1,261
Posted By fortyman
1940 ford deluxe windows

Are the windows on a 1940 ford fordor deluxe suppossed to roll all the way done to where you don't see them or do they stop a couple of inches above the bottom of the door.
Forum: Early V8 (1932-53) 12-18-2019, 12:52 PM
Replies: 2
Views: 1,083
Posted By fortyman
Re: Rear swing out quarter window

Thanks. Appreciate it.
Forum: Early V8 (1932-53) 12-17-2019, 10:56 AM
Replies: 2
Views: 1,083
Posted By fortyman
Rear swing out quarter window

Does window felt/glass setting tape or anything go inside the metal glass frame for the rear swing out quarter windows on fordor deluxe?
Forum: Early V8 (1932-53) 01-17-2018, 12:01 PM
Replies: 7
Views: 865
Posted By fortyman
Forum: Early V8 (1932-53) 01-17-2018, 10:08 AM
Replies: 7
Views: 865
Posted By fortyman
Re: 1940 steering box housing end plate

That is what I need. How can I go about getting from you?
Forum: Early V8 (1932-53) 01-16-2018, 10:44 AM
Replies: 7
Views: 865
Posted By fortyman
1940 steering box housing end plate

The tube on my housing end plate is broken. Can it be repaired or where can I find another.
Forum: Early V8 (1932-53) 01-03-2018, 07:52 PM
Replies: 4
Views: 942
Posted By fortyman
Re: 1940 Door Alignment

They were removed from the body prior to painting. Restoring from frame up.
Showing results 1 to 25 of 35

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 04:55 PM.