Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.06 seconds.
Search: Posts Made By: Ronnie
Forum: Early V8 (1932-53) 07-08-2020, 08:14 AM
Replies: 31
Views: 1,031
Posted By Ronnie
Re: 8ba block decking

https://www.innomach.com/cylinder-head-shims


Give them a call


R
Forum: Early V8 (1932-53) 07-05-2020, 11:49 AM
Replies: 18
Views: 448
Posted By Ronnie
Re: 8BA 12 V Starter?

Removing screws that hold in the coils is easier said than done.



R
Forum: Early V8 (1932-53) 06-01-2020, 03:21 PM
Replies: 42
Views: 1,364
Posted By Ronnie
Re: Rear exit manifolds for flathead 39 Ford

AA Ford needs to buy JWL's book to know why he should spend his money elsewhere on his project.


R
Forum: Early V8 (1932-53) 05-28-2020, 11:46 AM
Replies: 20
Views: 779
Posted By Ronnie
Re: Source for valve spring shims

Check with your local machine shop they may have them but can order them for you.


R
Forum: Early V8 (1932-53) 05-27-2020, 03:37 PM
Replies: 19
Views: 858
Posted By Ronnie
Re: Getting on Fordbarn

Good to see another old dude working with win 10 .
Chrome does work no issues here I just like Firefox,see no reason to change.
was win 10 a clean install or the upgrade?


R
Forum: Early V8 (1932-53) 05-27-2020, 12:43 PM
Replies: 19
Views: 858
Posted By Ronnie
Re: Getting on Fordbarn

Explorer has been replaced with Edge in win 10. I use Firefox because it has been good for 10 years +. Ask some of your buddies how they like 10. When 10 first came out it was a tough one but now its...
Forum: Early V8 (1932-53) 05-27-2020, 12:34 PM
Replies: 19
Views: 858
Posted By Ronnie
Re: Getting on Fordbarn

Win 7 reached its end of life and things weren't being updated and no support. Then banks required a win 10 upgrade as some of their offers weren't able to be used. I have run Firefox forever and it...
Forum: Early V8 (1932-53) 05-27-2020, 09:51 AM
Replies: 19
Views: 858
Posted By Ronnie
Re: Getting on Fordbarn

You should also consider win 10 it is really easy. I went from win 7 to win 10 seamless works well. Not a steep learning curve at at all.


R
Forum: Early V8 (1932-53) 05-18-2020, 12:10 PM
Replies: 20
Views: 891
Posted By Ronnie
Re: Torque tech.

https://www.tekton.com/torque-wrench-accuracy-and-calibration


R
Forum: Early V8 (1932-53) 05-11-2020, 02:54 PM
Replies: 51
Views: 6,337
Posted By Ronnie
Re: Relieving 8BA Block

2015 thread ???
Forum: Early V8 (1932-53) 05-07-2020, 12:58 PM
Replies: 54
Views: 1,994
Posted By Ronnie
Re: 1 Fly wheel 2 PP thread bad

Hope you don't fly,aircraft are one of the largest users you can find with heli coil approved repair scheme. On a side note welding cast iron and drilling and tapping will be another venture you...
Forum: Early V8 (1932-53) 04-28-2020, 04:06 PM
Replies: 67
Views: 2,844
Posted By Ronnie
Re: Same Clutch noise problem after third assembly and a lot of archive searches

Loctite 680 could also be a thought. Would certainly make a removal easier than spot welds. It has the properties that will work.



R
Forum: Early V8 (1932-53) 04-05-2020, 09:28 PM
Replies: 20
Views: 950
Posted By Ronnie
Re: valve seat cutter

You order Neway cutters with a .385" hub for Sioux.Or order with a .375 hub for for non Sioux .375" pilots. I have been associated with Neway. The hubs are not to be removed. They won't sell a hub...
Forum: Early V8 (1932-53) 04-05-2020, 02:49 PM
Replies: 20
Views: 950
Posted By Ronnie
Re: valve seat cutter

Hey Tub The job can be done with 1 pilot and 2 cutters at a reasonable cost. Can post info if desired. I have done 100's of seats for 25+ years with great sucess. You have to get a Snap on or Black...
Forum: Early V8 (1932-53) 03-26-2020, 02:05 PM
Replies: 21
Views: 1,640
Posted By Ronnie
Re: Resperator Production

We also need a chuckle now and then Ronnie





425459
Forum: Early V8 (1932-53) 03-07-2020, 10:20 AM
Replies: 24
Views: 731
Posted By Ronnie
Re: 1946 59a Mercury standard bore 3 3/16 pistons

Take that same ring and measure end gap at the bottom cylinder where the rings don't run.


R
Forum: Early V8 (1932-53) 02-29-2020, 03:28 PM
Replies: 7
Views: 547
Posted By Ronnie
Re: 8BA Crank Grind Size Limits?

Confirm bearing size with the machine shop before you order bearings. Bearings are under size not oversize. Any machine can order them no problems.


R
Forum: Early V8 (1932-53) 02-28-2020, 09:26 AM
Replies: 32
Views: 1,580
Posted By Ronnie
Re: I Don't Like Palnuts

Chevy is the answer no loc tite.


R
Forum: Early V8 (1932-53) 02-03-2020, 08:14 PM
Replies: 6
Views: 314
Posted By Ronnie
Re: Remote filter base.

How did you arrive at a wix 4770?


R
Forum: Early V8 (1932-53) 02-03-2020, 11:18 AM
Replies: 6
Views: 314
Posted By Ronnie
Re: Remote filter base.

24762 wix remote mount for a 3/4 x 16 filter any brand a 51515 wix will work

list of bases https://www.wixfilters.com/Speciality/Conversion.aspx

R
Forum: Early V8 (1932-53) 01-29-2020, 11:27 AM
Replies: 47
Views: 1,974
Posted By Ronnie
Re: Installing replacement pistons

Yes you should hone it isn't easy to not contaminate the rest of the engine.


My first post explained why the no hone was stated. Not my belief that honing must not be done. I myself haven't seen...
Forum: Early V8 (1932-53) 01-28-2020, 05:20 PM
Replies: 47
Views: 1,974
Posted By Ronnie
Re: Installing replacement pistons

Yes all that can be correct in many cases,the cautionary statement exists because the average shade tree fixer either doesn't know what is required to get a acceptable job done or is following 50...
Forum: Early V8 (1932-53) 01-27-2020, 03:37 PM
Replies: 17
Views: 931
Posted By Ronnie
Re: Liner/bore question.

its a 3/32" wall not 3/16"



R
Forum: Early V8 (1932-53) 01-03-2020, 08:55 PM
Replies: 53
Views: 2,851
Posted By Ronnie
Re: Install oil filter

Here is another spin on used for bypass filter situation. Quite common most of the filter mfg's will have this application. They already have a restriction orifice inside all you need is an adapter...
Forum: Early V8 (1932-53) 12-17-2019, 01:11 PM
Replies: 14
Views: 735
Posted By Ronnie
Re: 12 volt starter rpm reduction

Go here https://www.fordbarn.com/forum/showthread.php?t=86432&showall=1


Post #28


R
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 01:50 PM.