Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.06 seconds.
Search: Posts Made By: alanwoodieman
Forum: Early V8 (1932-53) Today, 04:47 PM
Replies: 25
Views: 1,180
Posted By alanwoodieman
Re: 1941 ford pickup heater

could you post a picture of your stock heater? would like to compare to some others
Forum: Early V8 (1932-53) Today, 08:27 AM
Replies: 31
Views: 928
Posted By alanwoodieman
Re: Australian 1940-1941 Ford Open Cab Pick-Ups

fender are for 3/4 ton truck and up. these tires are the same dia. as the original, so it does look different. 16" for 3/4 , ton had 17" and 1 1/2 ton had 20" all with the same fenders
Forum: Early V8 (1932-53) Yesterday, 12:35 PM
Replies: 23
Views: 971
Posted By alanwoodieman
Re: 46 Stake truck rebuild

as far as I can see there is no big piece missing just every tooth has a little from dragging the trans into gear before stopping. no problem!
Forum: Early V8 (1932-53) Yesterday, 08:45 AM
Replies: 23
Views: 971
Posted By alanwoodieman
Re: 46 Stake truck rebuild

if it just a chip, you can forget about it. but post a picture of it so the experts can give you advice. 12 volt is pretty easy to do and you can purchase a single wire gm style alternator and an...
Forum: Early V8 (1932-53) 01-11-2021, 05:00 PM
Replies: 21
Views: 829
Posted By alanwoodieman
Re: German H-block?

81a is the designate of 1938 which is the first year for 48 stud engines, you need to look on vanpelts website for block ID's
Forum: Early V8 (1932-53) 01-10-2021, 05:22 PM
Replies: 15
Views: 577
Posted By alanwoodieman
Re: Chassis question

zeke3 your 37 could have had a 60 hp motor, that is why you have two holes. these pieces are not cut, even on the short section of frame that came from a race car. the inner fender attaches to a...
Forum: Early V8 (1932-53) 01-10-2021, 02:33 PM
Replies: 25
Views: 1,180
Posted By alanwoodieman
Re: 1941 ford pickup heater

pull knob for defroster is just a plain sort of white/light tan in color with no lettering could not answer the question about switch panels
Forum: Early V8 (1932-53) 01-10-2021, 02:28 PM
Replies: 15
Views: 577
Posted By alanwoodieman
Re: Chassis question

40 ford auto frame, same as a 1/2 ton pick up, sedan delivery, and panel truck
Forum: Early V8 (1932-53) 01-10-2021, 01:51 PM
Replies: 8
Views: 351
Posted By alanwoodieman
Re: Windshield glass removal 39 coupe

I had a 36 and some one had put silicon gasket maker in the frame, I used a squirt bottle of gas to loosen it up to pull frame pieces off
Forum: Early V8 (1932-53) 01-10-2021, 01:48 PM
Replies: 2
Views: 210
Posted By alanwoodieman
Re: 52 F1 cluster gear

diameter? probably some inexpensive off the shelf tubing, noise it should be drowned in trans fluid and thus no noise
Forum: Early V8 (1932-53) 01-09-2021, 08:36 AM
Replies: 13
Views: 679
Posted By alanwoodieman
Re: No Oil Pressure While Cranking

sound like you may have a winner! put a rad on it and fill with water only and crank it up
Forum: Early V8 (1932-53) 01-07-2021, 10:27 PM
Replies: 14
Views: 540
Posted By alanwoodieman
Re: Chevy distibutor question for Bubba...

more dwell from dual points means more load on condenser/coil--doesn't?
Forum: Early V8 (1932-53) 01-07-2021, 07:12 PM
Replies: 4
Views: 311
Posted By alanwoodieman
Re: 40 transmission removal while on a 4 post lift?

did this to a 40 coupe, we strapped the front axle so the car would not move then we used a 6x6 beam and blocking to hold the car up, a sliding jack tray to support the rear and allow it to move back...
Forum: Early V8 (1932-53) 01-07-2021, 11:06 AM
Replies: 14
Views: 337
Posted By alanwoodieman
Re: C59A - Replacement/ fix for crankshaft pulley

needed same thing for my V8 conversion on my 8n tractor. don't cut up the three groove they are hard to find and can be quite valuable to old time hot rod builders
Forum: Early V8 (1932-53) 01-07-2021, 11:02 AM
Replies: 25
Views: 1,180
Posted By alanwoodieman
Re: 1941 ford pickup heater

pictures of two heater switch plates for 41, one that is square was broken when I got it and I just JB welded it back together other was found at a fleamarket with a 41 heater
Forum: Early V8 (1932-53) 01-06-2021, 10:24 PM
Replies: 31
Views: 863
Posted By alanwoodieman
Re: Prony Brake Ideas

my Dad in the Navy during WW2. check the engine/dyno
Forum: Early V8 (1932-53) 01-06-2021, 10:16 PM
Replies: 16
Views: 762
Posted By alanwoodieman
Re: 1940 Ford truck firewall kidney cover

no cover on my 41 1 1/2 ton former fire truck
Forum: Early V8 (1932-53) 01-06-2021, 08:20 AM
Replies: 25
Views: 1,180
Posted By alanwoodieman
Re: 1941 ford pickup heater

41 had a plate to mount below the dash similar to a 42 up but with only a hole for the heater switch. will get a picture of the two in my trucks today and post
Forum: Early V8 (1932-53) 01-05-2021, 08:56 AM
Replies: 23
Views: 971
Posted By alanwoodieman
Re: 46 Stake truck rebuild

the out put shaft bearing takes most of the stress on these trans, I suppose the brake drum has a lot do do with that. unless the teeth on the gears are ground off/chipped there is not much else to...
Forum: Early V8 (1932-53) 01-04-2021, 01:43 PM
Replies: 17
Views: 762
Posted By alanwoodieman
Re: Brakes Bendix style

pictures of work need to do to the spindles
Forum: Early V8 (1932-53) 01-03-2021, 01:36 PM
Replies: 28
Views: 1,185
Posted By alanwoodieman
Re: Fresh rebuilt 8BA Flathead

I do LIKE the lifting straps and the bar!
Forum: Early V8 (1932-53) 01-03-2021, 01:35 PM
Replies: 17
Views: 587
Posted By alanwoodieman
Re: headlights dim/ 53 f-100

corroded connections. clean your ground wire connections anyway, I had trouble with grounds in a 52 and finally ran a ground wire directly to the frame, problem solved
Forum: Early V8 (1932-53) 01-02-2021, 12:41 PM
Replies: 5
Views: 287
Posted By alanwoodieman
Re: cabs 1940- 1941

yes, the only difference is the 40 cab has a raised area in the middle of the dash for the cast Ford script, the cabs to 1947 had a flat area with two holes for a Ford badge. 42 to 47 had a...
Forum: Early V8 (1932-53) 01-01-2021, 01:51 PM
Replies: 20
Views: 494
Posted By alanwoodieman
Re: cam gear timing 1936 LB engine

two different cam drives were offered, so if you wanted to mate the wrong gears you would flip over the crank gear to get the teeth to align, with my fuzzy sometimes memory this may be the problem
Forum: Early V8 (1932-53) 01-01-2021, 01:48 PM
Replies: 4
Views: 394
Posted By alanwoodieman
Re: Is a 41 truck transmission the same as a 39 car?

same 78 case, different clevis arm on the clutch shaft, pin on the 39 arm, slotted on the 41. trucks generally had a 29 tooth first gear, a little different 2nd gear
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:48 PM.