Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.06 seconds.
Search: Posts Made By: Terry,OH
Forum: Early V8 (1932-53) Today, 05:01 PM
Replies: 13
Views: 1,057
Posted By Terry,OH
Re: Columbia inspection

When you reassemble the clutch make sure to follow instructions included in the kit. since your going to have it apart you should do a complete inspection. Do you know if the Columbia has been...
Forum: Early V8 (1932-53) Yesterday, 04:11 PM
Replies: 4
Views: 176
Posted By Terry,OH
Re: Clutch adjust.

make sure any and all the pedal bumpers are in place before adjusting.
Forum: Early V8 (1932-53) 08-11-2020, 05:08 AM
Replies: 4
Views: 266
Posted By Terry,OH
Re: Tranny broken, what parts will fit a 34?

Many of the different years gear sets will fit into the 34 case, (not sure of 50) but you have to get the front bearing in place on the shaft after installing the gear set and the front shaft. The...
Forum: Early V8 (1932-53) 08-04-2020, 06:06 PM
Replies: 10
Views: 354
Posted By Terry,OH
Re: NOS 1938-48 24 Stud Head Gaskets

The 41A gasket is the correct gasket for the 81A engine. You will note the small coolant holes are at the front and the rear coolant holes are larger.
Forum: Early V8 (1932-53) 07-31-2020, 05:49 AM
Replies: 12
Views: 707
Posted By Terry,OH
Re: Carb rebuild instructions

There are several on Ebay. Unless you know what your looking at you can easily get burned there. Many Ebay Carbs are missing parts, incorrect tops, bases, frozen throttle shafts, incorrect parts. ...
Forum: Early V8 (1932-53) 07-30-2020, 06:04 AM
Replies: 15
Views: 507
Posted By Terry,OH
Re: Late 21 stud 85 with 14 mm plugs

Suggest you get a copy of the Early Ford V8 Club of America 1938-39 restoration manual. It can answer many questions. the book is sold on their web site.
Forum: Early V8 (1932-53) 07-30-2020, 06:00 AM
Replies: 8
Views: 371
Posted By Terry,OH
Re: 1935 Sedan Convertible HELP

My best advice is to follow the instruction from Ford. Do you have the manual you found?
Forum: Early V8 (1932-53) 07-30-2020, 05:55 AM
Replies: 15
Views: 984
Posted By Terry,OH
Re: What is this attached to the carb on 1936 Ford

Vacuum line runs to the plate under the Carb. The vacuum is used to draw fuel vapor through the heating chamber from the Carb float bowl. The products of combustion do go into the engine through the...
Forum: Early V8 (1932-53) 07-29-2020, 04:01 PM
Replies: 9
Views: 509
Posted By Terry,OH
Re: Function trumps Awesome

What engine and distributor?
Forum: Early V8 (1932-53) 07-29-2020, 05:12 AM
Replies: 15
Views: 507
Posted By Terry,OH
Re: Late 21 stud 85 with 14 mm plugs

Are there any identifying marks on the heads? What are they?
Forum: Early V8 (1932-53) 07-28-2020, 11:50 AM
Replies: 12
Views: 707
Posted By Terry,OH
Re: Carb rebuild instructions

When I saw the photo of your engine I thought it was 85HP if it is, you want a 94 marked 91-99 made by Holley (embossed with H)
Forum: Early V8 (1932-53) 07-28-2020, 11:47 AM
Replies: 47
Views: 8,110
Posted By Terry,OH
Re: repairing rear axle housing bearing races..

Columbia Two Speed has the good races!
Forum: Early V8 (1932-53) 07-27-2020, 06:51 AM
Replies: 12
Views: 707
Posted By Terry,OH
Re: Carb rebuild instructions

You have a 92 or a 94? Is that a typo above? any other numbers on the Carb? Is the letter "H" embossed? The rebuilding kit instructions are very poor. Best to follow the Ford instructions from the...
Forum: Early V8 (1932-53) 07-26-2020, 05:43 AM
Replies: 16
Views: 817
Posted By Terry,OH
Forum: Early V8 (1932-53) 07-26-2020, 05:40 AM
Replies: 12
Views: 803
Posted By Terry,OH
Re: Uncle Max Carb Quality

Zenith Stromberg, very interesting, thanks for the post.
Forum: Early V8 (1932-53) 07-25-2020, 05:01 PM
Replies: 12
Views: 403
Posted By Terry,OH
Re: Rear brakes 40

I agree with the shoe retaining clip is bent. Is the brake shoe retracting spring installed properly? Cracked rubber boot on the brake cylinder? I do not see the clip that retains the hand brake...
Forum: Early V8 (1932-53) 07-25-2020, 09:19 AM
Replies: 26
Views: 829
Posted By Terry,OH
Re: Newbie to forum, and Ford.

The original Carb for your car is the Holley 91-99 it should be marked on the side of the middle body. Daytona sells a good rebuilding kit.
Forum: Early V8 (1932-53) 07-21-2020, 05:27 AM
Replies: 6
Views: 340
Posted By Terry,OH
Re: Door moulding 1936 convertible

The 35 is slightly different than the 36
Forum: Early V8 (1932-53) 07-18-2020, 12:06 PM
Replies: 11
Views: 508
Posted By Terry,OH
Re: power valve

Good luck. It seems many of the rebuilding PVs have too much of an angle at the base of the threads preventing the gasket from sealing also the soft gasket supplied often leaks. Charlie Schwendler...
Forum: Early V8 (1932-53) 07-18-2020, 09:03 AM
Replies: 7
Views: 372
Posted By Terry,OH
Re: Cabriolet window channel

Just about everyone with these channels 34- ? faces the same problem There are some old post regarding the installation of felt in the channel. I am not aware of any company offering a kit or the...
Forum: Early V8 (1932-53) 07-18-2020, 06:32 AM
Replies: 8
Views: 410
Posted By Terry,OH
Re: Elec novice

Batt terminal - to regulator case+ engine RPM need to be increased to see full generator output. Use an analog meter 7.0 to 7.7 v is good but 7.2 to 7.5 is better.
First with engine off turn on...
Forum: Early V8 (1932-53) 07-18-2020, 06:06 AM
Replies: 11
Views: 409
Posted By Terry,OH
Re: 40 coupe seat

post some photos especially the seat adjuster handle and the area between the backrest where the backrest pivot. Are the foot rest included?
Forum: Early V8 (1932-53) 07-15-2020, 04:44 PM
Replies: 14
Views: 697
Posted By Terry,OH
Re: Columbia overdrive

I can not speak for either of the two young men. I only believe John is heavy into parts and modifications, where Dan is into building complete units. They both are still doing their thing, you...
Forum: Early V8 (1932-53) 07-15-2020, 01:56 PM
Replies: 14
Views: 697
Posted By Terry,OH
Re: Columbia overdrive

In Temecula its Dan Krehbiel
Forum: Early V8 (1932-53) 07-14-2020, 05:37 AM
Replies: 6
Views: 357
Posted By Terry,OH
Re: 1935 Distributor Upgrade

I have a 35 with late 36 distributor with flat top coil modified with the 11A- parts for the advance and the engine runs and starts great. You will find the shaft with the flat plate and holes for...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:11 PM.