Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.06 seconds.
Search: Posts Made By: Patrick L.
Forum: Model A (1928-31) Today, 02:50 PM
Replies: 14
Views: 476
Posted By Patrick L.
Re: Condenser mount

Just had 5 bad ones, I think they had a bad batch. I also think they moved or sold.
Forum: Model A (1928-31) Today, 08:17 AM
Replies: 14
Views: 476
Posted By Patrick L.
Re: Condenser mount

Points or condenser ?

Buy the expensive ones. [ or a NOS]
NAPA may have them in stock or can overnight them. Ford V8 points are the same, I don't recall any change thru the 60s-70s [except for...
Forum: Model A (1928-31) Yesterday, 12:20 PM
Replies: 14
Views: 476
Posted By Patrick L.
Re: Condenser mount

The condenser doesn't care about the system voltage, 6 or 12 is fine.
Just connect the condenser the same polarity as the points. If system polarity is positive ground as original, then points...
Forum: Model A (1928-31) Yesterday, 07:27 AM
Replies: 20
Views: 1,778
Posted By Patrick L.
Re: axle key

LOL. Yep.

Same guy. We got a service call and I went. Super cold morning and a Detroit 71 series wouldn't start. Big surprise huh. I pull up and this clown has the mouth flipped open and is...
Forum: Model A (1928-31) 11-23-2020, 02:24 PM
Replies: 20
Views: 1,778
Posted By Patrick L.
Re: axle key

We had to fire a mechanic decades ago for a similar reason. Its not the only reason he got fired, he insisted on changing valve cover gaskets, carburetors, etc. with his air gun. He would pick the...
Forum: Model A (1928-31) 11-22-2020, 05:45 PM
Replies: 12
Views: 558
Posted By Patrick L.
Forum: Model A (1928-31) 11-21-2020, 10:20 AM
Replies: 3
Views: 239
Posted By Patrick L.
Re: 1930 Tudor - Rear Parking Light - whats this??

Yep, thats a light switch. The originals are good, the repro's are not. They to get full of oil/grease. Its a pretty basic simple thing.

A wiring diagram would be helpful and should be to be found...
Forum: Model A (1928-31) 11-21-2020, 10:13 AM
Replies: 12
Views: 558
Posted By Patrick L.
Re: Ignition System Question

My suspicion is that the wide plug probably caused the mis-fires and would not hurt the coil.

It does appear that some fellas have had bad luck with these coils lately. I've had good luck with...
Forum: Model A (1928-31) 11-21-2020, 10:07 AM
Replies: 7
Views: 502
Posted By Patrick L.
Re: oil lube circuit

Oil is pumped from base into valve chamber. Gravity takes over from there. Oil flowing into drip tray is picked up by the con rod dippers. Simple/ basic.
Forum: Model A (1928-31) 11-20-2020, 10:58 AM
Replies: 24
Views: 867
Posted By Patrick L.
Re: Determining Model A Gas Mileage

Figuring out fuel mileage ?

Fill tank up where you're comfortable
note odometer reading
drive car
Refill tank at some time again to a point where you're comfortable which should close as to the...
Forum: Model A (1928-31) 11-20-2020, 08:48 AM
Replies: 13
Views: 426
Posted By Patrick L.
Re: Maybe starter problems?

Good above info
Starter switch
Stuck stater drive
Poor battery connections/ground connection at frame
Forum: Model A (1928-31) 11-19-2020, 12:27 PM
Replies: 3
Views: 317
Posted By Patrick L.
Re: Clutch finger depth

Yes. The fingers should be .002" of each other.
Forum: Model A (1928-31) 11-19-2020, 08:27 AM
Replies: 27
Views: 778
Posted By Patrick L.
Re: new battery goin dead

Have you checked for a draw ?

If you have a draw then its either a bad ignition switch or generator cut-out.

If there is no draw then it seems like you have a bad battery.

You really...
Forum: Model A (1928-31) 11-18-2020, 05:00 PM
Replies: 27
Views: 778
Posted By Patrick L.
Re: new battery goin dead

OK, but why not find and fix the draw. Unless you're using an alternator and thats what drawing.
Forum: Model A (1928-31) 11-18-2020, 04:59 PM
Replies: 27
Views: 778
Posted By Patrick L.
Re: new battery goin dead

To check for the battery draw, it really makes no difference whether the test light is connected between the positive or negative leads. It'll still light the light if the draw is there.

And if...
Forum: Model A (1928-31) 11-17-2020, 10:49 AM
Replies: 13
Views: 710
Posted By Patrick L.
Re: Bent timing pin

Well, I guess that would make sense. I type this as I shake my head. But, I've pried on things I shouldn't have.
Forum: Model A (1928-31) 11-17-2020, 07:55 AM
Replies: 13
Views: 710
Posted By Patrick L.
Re: Bent timing pin

Are you talking about the actual timing pin or the distributor locating pin ?

Its surprising either would be bent. But it just goes to show that people can do about anything when they put their...
Forum: Model A (1928-31) 11-15-2020, 04:30 PM
Replies: 37
Views: 1,294
Posted By Patrick L.
Re: I知 wondering if my coil is going bad

I didn't think we were aware the points had been around for awhile.

Maybe something has 'slipped' or maybe the points are just poor quality.

Vaseline has been used for decades, its been a...
Forum: Model A (1928-31) 11-15-2020, 03:08 PM
Replies: 3
Views: 308
Posted By Patrick L.
Re: Front end tollerences...

If I'm making or pulling a frame I like it to be within 1/16"


When doing alignments If the vehicle is used mostly by one person I leave the pass door open. Of course for crowned roads I set...
Forum: Model A (1928-31) 11-15-2020, 12:24 PM
Replies: 37
Views: 1,294
Posted By Patrick L.
Re: I知 wondering if my coil is going bad

The cam and rubbing block just need to get used to each other. They'll wear into each other after awhile.
Forum: Model A (1928-31) 11-15-2020, 11:34 AM
Replies: 37
Views: 1,294
Posted By Patrick L.
Re: I知 wondering if my coil is going bad

The quality of points today varies greatly, the expensive ones are usually the best. The rubbing block wears quite quickly at first. The lube needs to get between the cam lobe and rubbing block. The...
Forum: Model A (1928-31) 11-14-2020, 05:44 PM
Replies: 37
Views: 1,294
Posted By Patrick L.
Re: I知 wondering if my coil is going bad

It probably didn't slip, it probably wore. It depends on the quality of the points and whether the block was lubed. Greasing it correctly is very important.
Forum: Model A (1928-31) 11-14-2020, 07:27 AM
Replies: 10
Views: 456
Posted By Patrick L.
Re: Gas cap 30/31 VENTED ??

Is the engine running properly ?

A new cap should be vented correctly. But look at the underside, remove the gasket and look at the vent hole[s].
Forum: Model A (1928-31) 11-12-2020, 03:36 PM
Replies: 5
Views: 300
Posted By Patrick L.
Re: Timing or ?

Remove the sparklers and squirt in some oil. Turn the engine over a few times. Squirt in some more oil and let it sit overnight. If that doesn't do it then you may have to remove the side cover and...
Forum: Model A (1928-31) 11-12-2020, 03:32 PM
Replies: 11
Views: 473
Posted By Patrick L.
Re: 2 tooth adjustment

Service bulletins, as said.

4th adjustment is often not needed.

They are pretty simple once you start doing it. All adjustments can be made while box is in the car.
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:48 PM.