Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 481
Search took 0.03 seconds.
Search: Posts Made By: daren007
Forum: Model A (1928-31) 02-23-2020, 03:31 PM
Replies: 55
Views: 2,867
Posted By daren007
Re: spark plug caps

My point is are we creating a shorter path to ground. How close do the caps fit to the Porcelain.
Forum: Model A (1928-31) 02-23-2020, 09:07 AM
Replies: 55
Views: 2,867
Posted By daren007
Re: spark plug caps

Are you somehow defeating the reason there are ribs on the porcelain by installing the caps over them?
Forum: Model A (1928-31) 02-18-2020, 06:52 PM
Replies: 17
Views: 519
Posted By daren007
Re: 180 Degree Thermostat "Hunting"

move the temp bulb to the cylinder head outlet neck.
Forum: Model A (1928-31) 02-17-2020, 10:38 PM
Replies: 11
Views: 439
Posted By daren007
Re: Is it possible to repair the upper radiator tank without radiator removal?

I learned the hard way on my "T". Do the job properly and drive worry free.
Forum: Model A (1928-31) 02-17-2020, 10:36 PM
Replies: 28
Views: 1,104
Posted By daren007
Re: Harbor Freight tape measures come up short

Easy. Just send in your tape for "Calibration".
Forum: Model A (1928-31) 02-17-2020, 07:14 PM
Replies: 8
Views: 418
Posted By daren007
Re: Rock chips on fender

3M spray on undercoating.
Forum: Model A (1928-31) 02-17-2020, 11:35 AM
Replies: 11
Views: 439
Posted By daren007
Re: Is it possible to repair the upper radiator tank without radiator removal?

You can screw around and remove the radiator later or get it over with and remove it now. Have a professional do the repair, You will not regret.
Forum: Model A (1928-31) 02-16-2020, 09:13 PM
Replies: 9
Views: 332
Posted By daren007
Re: High carbon on valves

Wet carbon on intake valves point to blow by or worn guides.
Forum: Model T (1909-1927) 02-16-2020, 09:10 PM
Replies: 2
Views: 140
Posted By daren007
Re: Timing, piston position...

You won the battle but you lost the war.
Forum: Model A (1928-31) 02-16-2020, 09:20 AM
Replies: 9
Views: 332
Posted By daren007
Forum: Model A (1928-31) 02-11-2020, 09:11 PM
Replies: 14
Views: 670
Posted By daren007
Re: Canvas Sport Coupe Top

Bought my top Kit from Classtique. You basically have one chance. If you can find someone with experience use it. Mike from Classtique was very helpful.
Forum: Model A (1928-31) 02-06-2020, 10:56 PM
Replies: 30
Views: 3,103
Posted By daren007
Re: short model a film

I guess I know where your head is at.
Forum: Model A (1928-31) 01-25-2020, 08:56 AM
Replies: 16
Views: 961
Posted By daren007
Re: King pin fit

Save time nd money plus aggravation. Have your local machine shop hone the bushings.
Forum: Model A (1928-31) 01-20-2020, 10:22 PM
Replies: 22
Views: 1,199
Posted By daren007
Re: Missing Valve seat

I also found a dropped valve head in another cylinder. Not model "A".
Forum: Model A (1928-31) 01-15-2020, 10:24 AM
Replies: 18
Views: 880
Posted By daren007
Re: Steam cleaning engine/trans?

Steam cleaning. The high pressure steam heat cuts the grease. Be careful how you do it you can force water into the engine. I played the restored clean and polished game with several cars over the...
Forum: Model A (1928-31) 01-13-2020, 11:15 PM
Replies: 7
Views: 319
Posted By daren007
Re: Door glass

Go back. It can be sanded.
Forum: Model A (1928-31) 01-11-2020, 09:22 AM
Replies: 25
Views: 1,215
Posted By daren007
Re: "B" Distributor timing with an "A" front cover

Addendum. Use the pin to find TDC then use indicator. The mark on the pulley will align at TDC or BDC. You must make sure you are at TDC on compression. Another method would be to put your thumb...
Forum: Model A (1928-31) 01-11-2020, 09:16 AM
Replies: 25
Views: 1,215
Posted By daren007
Re: "B" Distributor timing with an "A" front cover

Install a timing indicator. With number one piston at TDC mark the front pulley. I usually cut a slight slot with a hack saw and paint it white. You are good to go.
Forum: Model A (1928-31) 01-10-2020, 11:05 PM
Replies: 9
Views: 448
Posted By daren007
Re: Welch plug for carb

Welch plugs are round soft dish plugs for closing core holes in blocks and heads which most people call freeze plugs. Incidentally blocks and heads will crack before these plugs are forced out. ...
Forum: Model A (1928-31) 01-02-2020, 11:13 PM
Replies: 21
Views: 1,472
Posted By daren007
Re: Heater

Thanks. Sorry I missed that.
Forum: Model A (1928-31) 01-02-2020, 01:46 PM
Replies: 21
Views: 1,472
Posted By daren007
Re: Heater

What does a waffle manifold have to do with timing? I have had one car with this manifold and did not have any problems plus I have one in my present car and do not have problems with it.
Forum: Model A (1928-31) 12-27-2019, 10:55 PM
Replies: 5
Views: 454
Posted By daren007
Re: vacuum pump

Yes. Use the Model A.
Forum: Model A (1928-31) 12-27-2019, 09:58 AM
Replies: 11
Views: 917
Posted By daren007
Re: E-Zsteer draglink/track rod kit

Canadian your post made me laugh.
Forum: Model A (1928-31) 12-14-2019, 01:45 PM
Replies: 25
Views: 2,049
Posted By daren007
Re: Babbit vs Inserts

At what rpm are these industrial engines etc. running at?
Forum: Model A (1928-31) 12-12-2019, 10:54 PM
Replies: 45
Views: 2,531
Posted By daren007
Re: pinto engine on model A

Has anyone put a model "A" engine in a Pinto.
Showing results 1 to 25 of 481

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 11:12 PM.