Forum: Model T (1909-1927)
10-17-2022, 07:33 AM
|
Replies: 3
Views: 1,439
Re: Whats this tool?
Yes, I saw that. I was unable to open the catalog, knowing Ford it wouldn't be in there anyway because of proprietary rights. Maybe it has something to do with installing interior trim pieces? and...
|
Forum: Model T (1909-1927)
10-16-2022, 10:16 AM
|
Replies: 3
Views: 1,439
Whats this tool?
I am guessing it is from 'T' era, it may be more recent. I'd say it is a bronze casting and a notch with a groove at the end. It is a J.M. Waterston tool and the early style 'Ford' script on the...
|
Forum: Early V8 (1932-53)
12-01-2021, 01:31 PM
|
Replies: 53
Views: 5,388
Re: 1932 clutch issue
That pressure plate looks way too tall, I have a '41 transmission in mine and it doesn't look as tall as that.
For the best advice and parts go to:
http://www.vanpeltsales.com/
He flat knows these...
|
Forum: Early V8 (1932-53)
04-30-2020, 10:11 AM
|
Replies: 6
Views: 1,462
Re: '40ish Flywheel question
The clutch pressure plate are matched Ford #'s 7563 & 7550 disc, but I see now there are a bunch of variations, I was told that they were from a pickup and that hot rodders used them back in the day....
|
Forum: Early V8 (1932-53)
04-29-2020, 05:29 PM
|
Replies: 6
Views: 1,462
'40ish Flywheel question
Uh-oh, a hot rodder is about to ask a question! I need a picture or a description of what the flywheel looks like on a 40ish Ford pickup. My problem is that I have a hemi flywheel and a toploader...
|
Forum: Early V8 (1932-53)
03-22-2019, 10:35 AM
|
Replies: 7
Views: 1,702
Re: Wide5 wheel studs, need some
For some reason I am determined to mate the wide 5 and Buick, a need for self punishment I guess.
I'll probably do a tech piece on it over on the hamb, I'll give you headsup. I received a lot of...
|
Forum: Early V8 (1932-53)
03-22-2019, 09:00 AM
|
Replies: 7
Views: 1,702
Re: Wide5 wheel studs, need some
I looked the the Dorman 'on-line' catalog and contacted their tech, they advised me to go to Moroso or ARP.
I am doing what you did, mating the Buick drum to Wide 5 hub, I tried using (I just...
|
Forum: Early V8 (1932-53)
03-21-2019, 02:05 PM
|
Replies: 7
Views: 1,702
Wide5 wheel studs, need some
I need 4sets of Wide 5 wheel studs, I've checked with van Pelt and others without luck. I measured best I could and went to Dormans' website but they didn't have anything.
Any suggestions?
|
Forum: Early V8
12-10-2018, 04:49 PM
|
Replies: 0
Views: 967
Pinion Yoke, open drive
I have 40's era pickup banjo and the pinion yoke has rust pits on the machined surface where it contacts the seal. I'd like to replace it with a good one. The pinion has a tapered shaft, same as...
|
Forum: Early V8
12-10-2018, 04:43 PM
|
Replies: 1
Views: 873
|
Forum: Early V8
12-06-2018, 03:57 PM
|
Replies: 1
Views: 873
1937 v8-60
I have a very nice, complete V8-60 engine and transmission for sale. It is complete with ignition, starter, carb, generator, exhaust manifolds - all thats needed to start and run is battery and gas....
|
Forum: Early V8
12-01-2018, 01:05 PM
|
Replies: 0
Views: 857
V8-60, 1937
Came from running car, in good condition was spare motor for a hydroplane, the hydroplane got destroyed in a hurricane and time to cut the motor loose. It is complete, exhaust manifolds, carb,...
|
Forum: Early V8 (1932-53)
12-01-2018, 12:54 PM
|
Replies: 27
Views: 6,591
Re: Dual Overhead Cam Flathead
I recall similar engines developed for the Sherman tank, dual overhead cam. I saw one on ebay years ago, it wasn't complete and salty.
|
Forum: Model A (1928-31)
12-30-2017, 04:07 PM
|
Replies: 7
Views: 1,355
Re: Differences between Fords' 'A' & 'B'?
I'll look this evening when I get home but I am pretty sure I've seen, for instance, a 1930 45A and a 1930 45B Coupe. I remember flipping the pages back and forth to see if there was a feature that...
|
Forum: Model A (1928-31)
12-30-2017, 10:59 AM
|
Replies: 7
Views: 1,355
Differences between Fords' 'A' & 'B'?
I've been trying to figure out what why Ford called some models an 'A' and some as 'B' - not the motor designation. For instance, the coupe Model 45, there is a 45A and 45B. It seemed the sedans...
|
Forum: Early V8 (1932-53)
11-25-2017, 09:22 AM
|
Replies: 13
Views: 2,034
Re: Banjo question
Thanks guys, I guess I'm there. I checked inch pounds with a snap-on torque meter that has a dial.
Now I got to make a skinny wrench for the inner nut, I bought the set from ebay to remove the...
|
Forum: Early V8 (1932-53)
11-23-2017, 11:46 AM
|
Replies: 13
Views: 2,034
Banjo question
I'm rebuilding a late 40's open drive rear and I have a question about the pinion bearings. Shouldn't there be a crush sleeve or something between the bearings in that double bearing race? When I...
|
Forum: Late V8
03-07-2017, 06:14 PM
|
Replies: 1
Views: 1,023
|
Forum: Late V8
02-23-2017, 05:02 PM
|
Replies: 1
Views: 1,023
Antique Automobile Magazine
I have 5 issues of 'Antique Automobile' from the AACA, the top issue is May-June, 1969 vol 33 #3, the other 4 are still sealed but I expect they are from 1968 to 1969.
I have two groups of 5...
|
Forum: Model A (1928-31)
12-16-2015, 06:12 PM
|
Replies: 17
Views: 3,625
Re: Zenith float weight
I can see I'll have to get a better scale, I use a TOMCO. It might weight 31grams, I've never checked the accuracy of the scale. But I will tomorrow.
Thanks and Have a Safe Holiday, oj
|
Forum: Model A (1928-31)
12-16-2015, 04:45 PM
|
Replies: 17
Views: 3,625
Zenith float weight
I'm going thru a zenith and the float looks ok but it is heavy, it weights about 7/8ths of an ounce. Is that normal for these carbs?
|
Forum: Late V8 (1954+)
11-29-2015, 09:45 AM
|
Replies: 30
Views: 6,409
Re: Selling my stuff
Find a professional salesman, let them do a proper inventory and agree to pricing. Then stand back, observe and look after your interests.
|
Forum: Early V8 (1932-53)
11-03-2015, 10:29 AM
|
Replies: 28
Views: 5,618
Why positive ground?
What was theory as to having positive ground and what compelled manufactorors to switch to negative ground?
If I recall electrical theory right the voltage flows from positive to negative while...
|
Forum: Late V8 (1954+)
10-25-2015, 08:56 AM
|
Replies: 7
Views: 1,738
Re: Verify Power Valve is good?
When you say 'e-distr' if you speak of pertronix then you best have their coil to match circuit resistance and do not use ballast resister, they want full voltage (not necessary to reduce voltage...
|
Forum: Late V8 (1954+)
10-23-2015, 04:14 PM
|
Replies: 7
Views: 1,738
Re: Verify Power Valve is good?
You need a little fixture to test the PV in, easier and cheaper to replace it. the power valve value or rating is written in one of two places: if on the face there'll be like a 6 and it'll be right...
|