Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.07 seconds.
Search: Posts Made By: redmodelt
Forum: Model A (1928-31) Today, 12:27 AM
Replies: 4
Views: 183
Posted By redmodelt
Re: Bud Vase bracket

Any place you want that is out of the way.
Forum: Model A (1928-31) Today, 12:25 AM
Replies: 4
Views: 142
Posted By redmodelt
Re: Torque Tube / Drive Shaft Stuck

You did remove the clam shells? Maybe try jacking the rear end back up to lessen the angle. If the car was being driven I would not think the splines between the U-joint and drive shaft should be...
Forum: Model A (1928-31) 10-13-2019, 07:47 PM
Replies: 16
Views: 528
Posted By redmodelt
Re: Spindle Arm Nut

You have the wrong nut(s) installed. They should be low profile with a step on the back side to go over the boss that keeps the spindle from turning. That may be part of the problem, yours are too...
Forum: Model A (1928-31) 10-13-2019, 04:04 PM
Replies: 3
Views: 212
Posted By redmodelt
Re: wrndln please PM me.

Send him an Email. You can do both PM and emails.
Forum: Model A (1928-31) 10-13-2019, 09:54 AM
Replies: 9
Views: 261
Posted By redmodelt
Re: Painting Model A/AA Hubs and Backing Plates

We have been using the "VHT brake caliper" paint on the drums for some time. It covers good but not a thick paint. For the rear end and chassis we use, think it is same brand or similar, which is not...
Forum: Model A (1928-31) 10-12-2019, 08:47 PM
Replies: 11
Views: 616
Posted By redmodelt
Re: ?? Float a Motor rear mount

RE; Remenber rear floaters will change your caster..measure with old style then adjust floats to match..sc



People have been installing float a motor mounts for years, please elaborate on what...
Forum: Model A (1928-31) 10-12-2019, 11:00 AM
Replies: 15
Views: 583
Posted By redmodelt
Re: Need to move front spring across

If it is locked in there that tight, needs a good cleaning anyway. Would be a good time to clean and lube the spring leafs. Bumper jack sounds like a great way to get really hurt. Get the frame...
Forum: Model A (1928-31) 10-11-2019, 12:02 AM
Replies: 21
Views: 626
Posted By redmodelt
Re: rumble seat ins & outs

We had a customer that stands well over 6 foot and around 280, he got in and out of a rumble seat. No room for anyone else but he did it! :)
Forum: Model A (1928-31) 10-10-2019, 11:58 PM
Replies: 10
Views: 396
Posted By redmodelt
Re: Synthetic 680

I have not noticed any foaming with the 600 we get from Snyder's. I have used other brands that did. Make sure the vent hole on the shift tower is open.
...
Forum: Model A (1928-31) 10-10-2019, 11:47 PM
Replies: 29
Views: 1,005
Posted By redmodelt
Re: Oil In My Water

He has oil in the radiator not water in the oil.
Forum: Model A (1928-31) 10-10-2019, 07:46 PM
Replies: 29
Views: 1,005
Posted By redmodelt
Re: Oil In My Water

There is no where that the stud holes would come into contact with oil in the pan to wick up. Now if someone dumped a lot of oil in the adjacent cylinder and there was a bad gasket in that area, then...
Forum: Model A (1928-31) 10-10-2019, 05:16 PM
Replies: 29
Views: 1,005
Posted By redmodelt
Re: Oil In My Water

There is no oil in those locations all studs would end in the water jacket if they were open to same, but they are not (normally). Keep looking.
Forum: Model T (1909-1927) 10-10-2019, 05:07 PM
Replies: 18
Views: 458
Posted By redmodelt
Re: Model T Sparkplugs

Unless you have sealing washers with the cores or can find bodies with good ones in them..well lets just say there is more to putting plugs together then just installing new cores.
Forum: Model T (1909-1927) 10-08-2019, 07:10 PM
Replies: 18
Views: 458
Posted By redmodelt
Re: Model T Sparkplugs

Yes to the 1/2 thread plugs and deeper part. No there is no list. Like oil there are many opinions of what works well in someones car. What works well for me does not mean it will work well for you. ...
Forum: Model A (1928-31) 10-07-2019, 08:25 PM
Replies: 29
Views: 1,005
Posted By redmodelt
Re: Oil In My Water

The valve galleries would be about the only place that would be close to the water jacket or blown gasket on engine that pumping a heck of a lot of oil, but in both cases there would be water in the...
Forum: Model T (1909-1927) 10-07-2019, 08:16 PM
Replies: 7
Views: 392
Posted By redmodelt
Re: Model A intake on a Model T

You can use the 3 in one T copper faced gaskets and don't need the plate. The nice thing about the plate is that you can fit gland rings on both sides, but lots of people have done it without the...
Forum: Model A (1928-31) 10-07-2019, 12:20 AM
Replies: 29
Views: 1,005
Posted By redmodelt
Re: Oil In My Water

4 weeks wouldn't hardly be any time in the car restoration world. :) While not impossible, it is kinda hard to get oil into the cooling system without being put there, water in the oil not so hard.
Forum: Model A (1928-31) 10-07-2019, 12:17 AM
Replies: 17
Views: 505
Posted By redmodelt
Forum: Model A (1928-31) 10-06-2019, 08:53 PM
Replies: 29
Views: 1,005
Posted By redmodelt
Re: Oil In My Water

Re;As long as the compression readings were taken with the spark advance lever at full retard and all

I think you meant throttle and if you didn't, spark has nothing to do with checking...
Forum: Model A (1928-31) 10-06-2019, 07:48 PM
Replies: 17
Views: 505
Posted By redmodelt
Re: Trans oil leaking from speedo housing

Did you check at the fill plug hole for proper level? Yes there is a gasket between the speeo turtle and tube. When was the last time you added grease to the U-joint housing?
Forum: Model A (1928-31) 10-06-2019, 07:44 PM
Replies: 7
Views: 319
Posted By redmodelt
Re: Rear main tube?

Pull the oil fill tube and run the scope in there. Don't have to lay on your back under the car nor drain the oil. Plus it is a bigger hole to work thru. Don't forget, there are the baffles that...
Forum: Model T (1909-1927) 10-04-2019, 04:19 PM
Replies: 8
Views: 364
Posted By redmodelt
Re: Bench testing coils....

When I posted the photo I did not see how it was wired. Removed photo to avoid confusion.
Forum: Model A (1928-31) 10-04-2019, 10:21 AM
Replies: 6
Views: 262
Posted By redmodelt
Re: Interior piece

Snyders sells the kit to replace the filler that slides into the metal channel. The original was pressed card stock.
...
Forum: Model A (1928-31) 10-04-2019, 01:25 AM
Replies: 11
Views: 406
Posted By redmodelt
Re: Model A Electrical Inquiry re: cut out

Without knowing at what RPM he is taking the reading, 15V's seem high. At about 1425 to 1500 RPM on the Wilson test stand, the generator I checked today was getting around 7V's output and set for...
Forum: Model T (1909-1927) 10-04-2019, 01:08 AM
Replies: 8
Views: 364
Posted By redmodelt
Re: Bench testing coils....

Put the plug wires on the bottom terminals. The top ones go to the timer. Looks good.
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 11:00 AM.