Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 136
Search took 0.01 seconds.
Search: Posts Made By: STAN WHITE
Forum: Early V8 (1932-53) 05-03-2021, 10:28 AM
Replies: 19
Views: 853
Posted By STAN WHITE
Re: Dupont Centari Acrylic Enamel

Tom, The name of the company is EXALTA,Formerly (Dupont). They have what you are looking for. They are on the Internet. Stan
Forum: Early V8 (1932-53) 05-03-2021, 09:32 AM
Replies: 19
Views: 853
Posted By STAN WHITE
Re: Dupont Centari Acrylic Enamel

I needed the same thing, there is an outfit that makes the same thing I do not know the name or their number. But I will find it for you and get back to you. Stan 775 265 5333. If you want give me...
Forum: Early V8 (1932-53) 04-29-2021, 09:53 PM
Replies: 3
Views: 245
Posted By STAN WHITE
Re: 34 ford front fender tie/front fender air deflector

David How would the screw hold the the welting. What I understand is that the welting is cut and both ends are butted together below the Grill on a 34 but not on a 33. Stan
Forum: Early V8 (1932-53) 04-29-2021, 03:01 PM
Replies: 3
Views: 245
Posted By STAN WHITE
34 ford front fender tie/front fender air deflector

I am trying to figure thi out. I am a little bit confused.Got some answsers in the past about the air deflector that is behind the grill. the answer was tha the air deflector went in below or from...
Forum: Early V8 (1932-53) 04-29-2021, 11:45 AM
Replies: 60
Views: 5,453
Posted By STAN WHITE
Re: Harmon Collins build thread ...

34 five window, Thanks for the photo brings back many memories! Ed was a good guy very knoelgable person I learned a lot from him. I went up to I think Windsor when he had his Willys there bought...
Forum: Early V8 (1932-53) 04-28-2021, 02:42 PM
Replies: 60
Views: 5,453
Posted By STAN WHITE
Re: Harmon Collins build thread ...

Bubba A few questions. First I purchased two of your Condensers they are very nice, Very satisfied. My question is on the Blue Bosch 12 volt coils. I understand that they are 3 Ohms and have a built...
Forum: Early V8 (1932-53) 04-24-2021, 04:21 PM
Replies: 3
Views: 243
Posted By STAN WHITE
33 dash engine turned instrument panel.(thickness)

Anyone out there with a original 33 dash gage panel. Would like to know the thickness of it. I want to make one using S&W Gages. Thank you. Stan
Forum: Early V8 (1932-53) 04-23-2021, 02:51 PM
Replies: 6
Views: 320
Posted By STAN WHITE
Re: 1934 coupe rear window channel

I have an original 34 3wdw, I have not done it yet , but rear glass needs replacing. (Foggee from age. Plus will not roll up/or down. Problem is the car was upholstered back in the late 60s. So I...
Forum: Early V8 (1932-53) 04-19-2021, 06:27 PM
Replies: 10
Views: 560
Posted By STAN WHITE
34 ford radiator where to purchase?

I need a radiator for my 34 ford with a flathead engine. I hear that Brass Works Radiators are a good choice. I also would like to know if I need to use a pressure CAP. And how much pressure to run....
Forum: Early V8 (1932-53) 04-12-2021, 09:14 PM
Replies: 10
Views: 712
Posted By STAN WHITE
Re: Moving Day

AT LEAST YOU DID NOT GIVE UP.GREAT MORE POWER TO YOU! i AM 83 THIS MONTH, i TOOK MY 34 3WDW APART 35 YEARS AGO AND STARTED WORKING ON IT ABOUT ONE YEAR AGO. MAKING PROGRESS Takes a little longer as...
Forum: Early V8 (1932-53) 04-12-2021, 05:51 PM
Replies: 6
Views: 318
Posted By STAN WHITE
Re: 34 ford radiator

Thanks Cars3. I guess I will have to go with one of those if they are still available. Did every thing line up for grill & inner fender panels? Front Hood latch mounts & radiator rods etc?. Thanks...
Forum: Early V8 (1932-53) 04-12-2021, 05:15 PM
Replies: 6
Views: 318
Posted By STAN WHITE
34 ford radiator

I HAD A SPECIAL RADIATOR BUILT MANY YEARS AGO. IT IS WHAT i WOULD CALL A SHOW RADIATOR. ALL BRASS WITH A PRESSURE CAP. PUTTING MY COUPE BACK TOGETHER AFTER MANY YEARS. SO I MOCKED IT UP WITH FRONT...
Forum: Early V8 (1932-53) 04-04-2021, 10:55 PM
Replies: 2
Views: 263
Posted By STAN WHITE
1934 Ford Single bulb headlight bulbs (12 Volt)

I am in the process of instaling my head lights. They are singel bulb units I switched to 12 Volts. Where would I purchase two filament 12 volt bulbs that are good? Thanks Stan
Forum: Early V8 03-28-2021, 08:10 PM
Replies: 0
Views: 215
Posted By STAN WHITE
Cal 1934 License Plates & One 1951 Cal

California License Plates (1934) Three sets have had for over 35 Years. All are perfect good paint no extra holes. Can run as is. They are the following. Set A=8k 91 B=9P 474 C=4J3476 Also one...
Forum: Early V8 03-28-2021, 07:34 PM
Replies: 0
Views: 225
Posted By STAN WHITE
3/8x3/8 pistons

I have a new set of jahns piston that I would like to get rid of. They are jahns three ring with pins. They are marked 3/8 X 1/8 I assume they are for a 3/8x3/8 Engine. I think that would be a...
Forum: Early V8 (1932-53) 03-27-2021, 02:05 PM
Replies: 3
Views: 234
Posted By STAN WHITE
34 ford headlights,Disassembly

Proper way to disassemble headlights.on original 34 headlights any help from someone who knows. Thanks Stan
Forum: Early V8 (1932-53) 03-21-2021, 09:41 PM
Replies: 3
Views: 219
Posted By STAN WHITE
Re: 1934 ford front fender tie

Thank you David G, Then it will require a large diameter flat washer. Right now it just has a small lock washer. Thanks for your reply. That makes sense. The fender welting runs all the way back to...
Forum: Early V8 (1932-53) 03-21-2021, 05:44 PM
Replies: 3
Views: 219
Posted By STAN WHITE
1934 ford front fender tie

I took this car apart 25 years ago, The older I get the less I remember some things. Other things I can go back and remember 60 years ago at least I THINK i can. MY QUESTION IS ON THE FRONT FENDER...
Forum: Early V8 (1932-53) 03-19-2021, 12:31 AM
Replies: 62
Views: 3,588
Posted By STAN WHITE
Re: ARP bolts

I have found that the standard 7/16 stud that you would purchase from your average parts store for the heads are not concentric, from end to end. If you put them in a lathe using a 7/16 Collet ,...
Forum: Early V8 (1932-53) 03-14-2021, 11:04 PM
Replies: 45
Views: 3,319
Posted By STAN WHITE
Re: Flathead Cams

I am using a Potvin.425 Eliminator . I have one from the late 50s. I am running it in a 276 C.I. 59AB It is a 1/4X 5/16 Configuration. They were ground on a steel billet 1932 cam. Most guys think...
Forum: Early V8 03-06-2021, 10:10 PM
Replies: 0
Views: 168
Posted By STAN WHITE
1934 ford air defector

I NEED THE AIR DEFECTOR FOR A 1934 ford. it mounts between front fenders behind and below the grill, Sheet metal and triangular shaped. Also has the Crank hole in it. I HOPE SOMEONE CAN HELP ME FIND...
Forum: Early V8 (1932-53) 03-05-2021, 11:44 AM
Replies: 3
Views: 373
Posted By STAN WHITE
34 ford front fender tie

What is the proper method for installing the front fender tie? Thanks. Stan
Forum: Early V8 (1932-53) 02-23-2021, 12:00 PM
Replies: 11
Views: 925
Posted By STAN WHITE
34 front fenders assembly

I would like to know the proper procedure for assembly of front fenders center section assembly & the triangler shape pan, also the front fender tie that ties front fenders together. Thanks Stan
Forum: Early V8 (1932-53) 02-19-2021, 04:17 PM
Replies: 5
Views: 580
Posted By STAN WHITE
Crankshaft seal 59ab

LOOKING FOR HELP ON THE FRONT COVER FOR A 59AB ENGINE CRANKSHAFT SEAL. i HAVE ALWAYS USED THE OLD STYLE ROPE SEAL. THERE ARE NEW STYLE SEALS AVAILABLE, i HAVE TWO ONE IS ALUMINUM WITH AN OUTER O RING...
Forum: Early V8 (1932-53) 02-17-2021, 12:25 AM
Replies: 60
Views: 5,453
Posted By STAN WHITE
Re: Harmon Collins build thread ...

Bubba I have a question on the vacuum brake. I was told by a Flathead engine builder that I did not need to use the vacuum brake. he said that I needed to back it off by a couple of turns. This was...
Showing results 1 to 25 of 136

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 01:17 PM.