Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 35
Search took 0.00 seconds.
Search: Posts Made By: Fhane
Forum: Model A (1928-31) 06-26-2020, 01:27 PM
Replies: 15
Views: 822
Posted By Fhane
Re: Your best method for drilling out rivets?

Center punch and then use a center drill countersink. You can find them on Amazon or Harbor Freight.
Forum: Model A (1928-31) 02-11-2020, 02:25 PM
Replies: 17
Views: 917
Posted By Fhane
Re: Wobble On Braking

GRABBING AND SPRAGGING

A brake is said to grab when it has an unusually high shoe factor, making fine control difficult or even impossible. A spragging brake locks solid as soon as it is...
Forum: Model A (1928-31) 02-11-2020, 01:49 PM
Replies: 17
Views: 917
Posted By Fhane
Re: Wobble On Braking

Grabbing or wobbling is sometimes experienced when a vehicle has been standing overnight. Linings tend to absorb moisture from the atmosphere, which causes slight swelling and an increase in...
Forum: Model A (1928-31) 02-05-2020, 07:09 PM
Replies: 23
Views: 1,674
Posted By Fhane
Re: loping engine?

Two things may help

Google loping engine.

Run a test with a vacuum gauge if possible.
Forum: Model A (1928-31) 01-08-2020, 10:44 PM
Replies: 13
Views: 751
Posted By Fhane
Re: Remove sector needle bearings

Yes, stock housing. If you need it my phone number is 772 341 8291
Forum: Model A (1928-31) 01-08-2020, 05:43 PM
Replies: 13
Views: 751
Posted By Fhane
Re: Remove sector needle bearings

If you need a sector housing I can send you one for the cost of shipping.
Forum: Model A (1928-31) 10-21-2019, 07:20 AM
Replies: 27
Views: 1,997
Posted By Fhane
Re: Model A backfire, can't move

Check the water in the radiator. It’s may have overheated.
Forum: Model A (1928-31) 10-19-2019, 05:39 PM
Replies: 10
Views: 844
Posted By Fhane
Re: Fuel shut off

Try Amazon. 3/8 mini ball valve.
Forum: Model A (1928-31) 09-30-2019, 05:58 PM
Replies: 32
Views: 1,957
Posted By Fhane
Re: Every 500 Miles!??

Bad arthritis go to amazon.com. Search oil extractor pump.
Forum: Model A (1928-31) 09-28-2019, 04:49 PM
Replies: 15
Views: 1,038
Posted By Fhane
Re: Hand riveting tool ?

Aircraftspruce.com has the tool you need. Search brake rivet
Forum: Model A (1928-31) 09-28-2019, 08:17 AM
Replies: 16
Views: 1,220
Posted By Fhane
Re: Oil pressure

Could it be air trapped in the oil pressure line to the gauge
Forum: Model A (1928-31) 09-24-2019, 06:44 AM
Replies: 16
Views: 1,088
Posted By Fhane
Re: White crap in carb bowl - Pic

Try taking a sample of your gas in a glass jar. Add a small amount of water to the jar. Let the jar sat for a few hours. If alcohol is present you will see phase separation.
Forum: Model A (1928-31) 07-26-2019, 05:17 PM
Replies: 14
Views: 1,604
Posted By Fhane
Re: Brattons Radiators

I have purchased at least 18 in the past years from Brattonísís to install in customers cars. No problems at all. One customer commented he could smell the fresh paint on one. Like anything else...
Forum: Model A (1928-31) 05-18-2019, 06:56 PM
Replies: 9
Views: 1,030
Posted By Fhane
Re: What correct screws and/or fasteners are needed?

Is anybody making the body screws (3) for Tillotson carburetor?
Forum: Model A (1928-31) 05-18-2019, 06:42 PM
Replies: 5
Views: 775
Posted By Fhane
Re: Body to Hood Alignment

Could be a couple of adjustments needed. Body does not seem to be square on the frame. Hood might need shims under the center shim rod in the rear of the hood. Brattons PN 22391. Bottom of...
Forum: Model A (1928-31) 04-12-2019, 04:55 PM
Replies: 9
Views: 747
Posted By Fhane
Re: Disconnect Pitman Arm????

Make sure the bolt is completely removed.
Forum: Model A (1928-31) 02-08-2019, 09:01 AM
Replies: 33
Views: 3,490
Posted By Fhane
Re: Flywheel housing

I am a little confused. In post number 11 what is being aligned?
Forum: Model A (1928-31) 02-06-2019, 06:31 PM
Replies: 36
Views: 2,091
Posted By Fhane
Re: Is fuel bubbling normal

Plastic fuel filter. Sounds like a fire hazard to me. Should be a steel fuel line. No rubber no plastic.
Forum: Model A (1928-31) 01-14-2019, 08:36 AM
Replies: 24
Views: 2,812
Posted By Fhane
Re: Rear Main Bearing Oil Behavior

About ten years ago a nice 1930 Model A came into the shop with a small rear main leak.
I dropped the pan. Bearings were a little loose and no rear main drain tube. Did not adjust the bearings....
Forum: Model A (1928-31) 10-28-2018, 09:57 AM
Replies: 9
Views: 857
Posted By Fhane
Re: Steering worm gear install

I have a press and fixtures for installing the worm on the shaft. If you are near Stuart, Florida I would be glad to do it for you.
Forum: Model A (1928-31) 05-27-2018, 06:02 PM
Replies: 16
Views: 2,212
Posted By Fhane
Re: 30 model A water pump ID help

Looks like a water pump from a mail truck or an industrial engine

Fhane Jones
Stuart Model A Parts and Service
Stuart, Florida
772 341 8291
Forum: Model A (1928-31) 04-27-2018, 01:21 PM
Replies: 26
Views: 3,837
Posted By Fhane
Re: New or Used Parts

Hi Copgib

I have been following your brake thread. I don’t normally advertise for myself or others, but in this case maybe I can offer some advise. In Florida I know of 3 mechanical brake...
Forum: Model A (1928-31) 02-22-2018, 09:28 AM
Replies: 15
Views: 1,987
Posted By Fhane
Re: Transmission case repair

Very good. Thanks
Forum: Model A (1928-31) 12-30-2017, 07:36 PM
Replies: 7
Views: 852
Posted By Fhane
Re: Differences between Fords' 'A' & 'B'?

This might be of some help

https://www.macsautoparts.com/store/model-a-specs/
Forum: Model A (1928-31) 10-09-2017, 06:26 AM
Replies: 18
Views: 1,732
Posted By Fhane
Re: dip stick

333597

This might help
Showing results 1 to 25 of 35

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:38 AM.