Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 416
Search took 0.02 seconds.
Search: Posts Made By: 37 Cab
Forum: Early V8 (1932-53) 10-06-2019, 10:31 AM
Replies: 10
Views: 331
Posted By 37 Cab
Re: Aod in 1950 ford 8ba

Also keep in mind an AOD is totally reliant on the throttle valve for shift pressures. It is critical that it be adjusted correctly for correct shift points and trans pressures. A misadjusted...
Forum: Early V8 (1932-53) 10-06-2019, 09:21 AM
Replies: 10
Views: 331
Posted By 37 Cab
Re: Aod in 1950 ford 8ba

Also, the electronic transmission (4R70W) is virtually the same as an AOD internally so the wide ratio planetary gears will interchange into the AOD. The W in 4R70W stands for wide ratio.
Forum: Early V8 (1932-53) 09-26-2019, 06:55 PM
Replies: 10
Views: 461
Posted By 37 Cab
Re: Are all yellow top coils 12 volt

Is the whole car there? If so pull a light bulb and apply 12 volts. See if it lives.
Forum: Early V8 (1932-53) 09-21-2019, 07:01 PM
Replies: 13
Views: 540
Posted By 37 Cab
Re: 1937 85hp cylinder sleeve possibly leaking water into the pan?

A little off topic but I was a Ford dealer tech all my life. When they did the cash for clunkers program in the early 2000s the cars we got in under that program were deemed junk and not allowed to...
Forum: Early V8 (1932-53) 09-14-2019, 06:49 AM
Replies: 19
Views: 691
Posted By 37 Cab
Re: What kind of heads are these - 49 Merc flathead?

Notice the long hoses on the floor behind the engine.
Forum: Early V8 (1932-53) 09-07-2019, 04:18 PM
Replies: 26
Views: 1,599
Posted By 37 Cab
Re: Junk yards of the '40s '50s

When I was a kid I built my first hot rod using all junkyard parts. Ended up with a 55 Fairlane with a 428 and a top loader 4 speed. Good luck doing anything like that these days. Think I gave 200...
Forum: Early V8 (1932-53) 09-07-2019, 04:12 PM
Replies: 11
Views: 550
Posted By 37 Cab
Re: Starter heat soak

My car has Fenton cast iron headers and the header is so close the stud for the battery cable had to be ground off some for clearance. I have no issues starting even on the hottest day after extended...
Forum: Early V8 (1932-53) 09-06-2019, 07:43 AM
Replies: 18
Views: 675
Posted By 37 Cab
Forum: Early V8 (1932-53) 09-03-2019, 03:14 PM
Replies: 3
Views: 238
Posted By 37 Cab
Re: Speedometer cable

I found a NOS cable on Ebay. Got it coming. Thanks for the help guys.
Forum: Early V8 (1932-53) 09-02-2019, 12:43 PM
Replies: 3
Views: 238
Posted By 37 Cab
Speedometer cable

I am getting ready to install the Mitchell overdrive in my 37. My speedometer quit recently and was "bouncing" since I got the car. There is a spot in the cable housing where it was damaged "pinched"...
Forum: Early V8 (1932-53) 09-01-2019, 09:19 AM
Replies: 8
Views: 369
Posted By 37 Cab
Re: exhaust pipe wrap

Keep in mind the heat retained in the pipe will eventually cause the metal to become brittle. Also if it gets wet it will retain moisture until heated up enough to dry out. I have seen more than one...
Forum: Early V8 (1932-53) 08-29-2019, 02:06 PM
Replies: 18
Views: 795
Posted By 37 Cab
Re: Any idea what tis frame is?

How about a Lincoln with the body cut off? Looking at the front and rear crossmembers it appears to have been built with those.
Forum: Early V8 (1932-53) 08-29-2019, 10:06 AM
Replies: 18
Views: 795
Posted By 37 Cab
Re: Any idea what tis frame is?

Maybe a commercial with passenger car axles? But then.. Didn`t commercial trucks have parallel leaf springs in the back?
Forum: Early V8 (1932-53) 08-28-2019, 07:46 PM
Replies: 18
Views: 795
Posted By 37 Cab
Any idea what tis frame is?

It has wide five wheels and cable brakes like 37-38 Ford but what is it?405338
Forum: Early V8 (1932-53) 08-25-2019, 08:43 PM
Replies: 13
Views: 632
Posted By 37 Cab
Re: Mystery Door Handle

Looks like the rumble seat handle on my 37.
Forum: Early V8 (1932-53) 08-23-2019, 06:39 PM
Replies: 10
Views: 521
Posted By 37 Cab
Re: Safety Wire

We need a "like" button.
Forum: Early V8 (1932-53) 08-19-2019, 07:38 PM
Replies: 12
Views: 889
Posted By 37 Cab
Re: Got the call

I went with lever. My car has reversed springs so I kind of expect clearance issues. Steve at Mitchell didn`t think so, but we shall see. The reason I ask about the wheels is because a previous owner...
Forum: Early V8 (1932-53) 08-18-2019, 05:39 PM
Replies: 12
Views: 889
Posted By 37 Cab
Re: Got the call

Thanks Kerk.. I will be sure to lift the car with the rear heavy and keep an eye on it. I am excited to get this done. Up to this point I have not been comfortable taking my car over 20-30 miles from...
Forum: Early V8 (1932-53) 08-17-2019, 09:14 PM
Replies: 32
Views: 1,480
Posted By 37 Cab
Forum: Early V8 (1932-53) 08-17-2019, 08:01 PM
Replies: 11
Views: 427
Posted By 37 Cab
Re: Rack & Pinion Steering for 1947 Ford

I once replaced the steering cable on my jet boat and the new "rack" would only fit under the worm drive at the steering wheel. Never gave it a thought that the original was above the worm.... ...
Forum: Early V8 (1932-53) 08-17-2019, 04:37 PM
Replies: 4
Views: 313
Posted By 37 Cab
Re: Battery Charging Experts -

Do you have a hydrometer? Might check the specific gravity of each cell. Sometimes the old ways are the most reliable.
Forum: Early V8 (1932-53) 08-17-2019, 03:50 PM
Replies: 54
Views: 2,140
Posted By 37 Cab
Re: 1932 serial number starts with D5

I have had a couple vehicles and trailers with Calif. assigned VINs and they all started with CA.
Forum: Early V8 (1932-53) 08-17-2019, 05:53 AM
Replies: 12
Views: 889
Posted By 37 Cab
Got the call

I got a call from Mitchell yesterday letting me know my overdrive is finished and shipping. I am looking forward to getting it in soon. My first question is, Will it be Ok to leave my rear tires on...
Forum: Early V8 (1932-53) 08-15-2019, 09:19 PM
Replies: 23
Views: 1,462
Posted By 37 Cab
Re: Fuel pump rod - what is the purpose of umbrella?

My take is.. If my machinist told me the umbrella on my push rod was there to pump air.. I would worry I had the wrong machinist.
Forum: Early V8 (1932-53) 08-10-2019, 10:57 AM
Replies: 27
Views: 944
Posted By 37 Cab
Re: Carburator problem, I think

Also could be a failed power valve if equipped but I`m sure the Holley tech went over that with you. Hard to say VIA internet.. Rich or lean? Do the idle adjustment screws make any difference? Are...
Showing results 1 to 25 of 416

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 10:19 AM.