Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.04 seconds.
Search: Posts Made By: Bud
Forum: Model A (1928-31) 03-16-2020, 11:36 AM
Replies: 43
Views: 2,055
Posted By Bud
Re: Flywheel Housing Alignment

I had to shim my crank flange because the original rebuilder did not grind it square. It was out .0020". I used a half-circle shim captured by the flywheel screws to fix the problem. It can't get...
Forum: Model A (1928-31) 02-19-2020, 12:22 PM
Replies: 10
Views: 726
Posted By Bud
Re: 97 stromberg on a standard 28 -possible?

Location of Lawrie's Mod: https://www.fordbarn.com/forum/showthread.php?t=211685&highlight=float+valve+mod
Forum: Model A (1928-31) 02-10-2020, 07:58 PM
Replies: 5
Views: 356
Posted By Bud
Re: 1931 Victoria Door Hinge Mirror

I have found on my '31 S/W town sedan that I need a longer mirror arm than the reproduction mirror arm pictured on this thread. That mirror arm is 5.5" from the hinge pin center to the hole for...
Forum: Early V8 (1932-53) 02-04-2020, 10:15 PM
Replies: 18
Views: 1,145
Posted By Bud
Re: Otis the drunk got a car

Does the car still exist?
Forum: Model A (1928-31) 12-22-2019, 07:59 PM
Replies: 13
Views: 1,024
Posted By Bud
Most Recommended On-Line Auctioneers

If one wanted to find a reputable auction service (other than eBay) that would handle a small collection (parts, literature, collectibles, and maybe one vehicle) in an on-line format, who would you...
Forum: Model A (1928-31) 10-09-2019, 11:27 AM
Replies: 34
Views: 2,378
Posted By Bud
Re: Trailering tips for protection

One of my club members towed his Model A to a National Meet (it was a show car) on an open trailer. But he rigged up a large air deflector made of plywood and 2x4's and placed it in front of the car...
Forum: Late V8 (1954+) 10-02-2019, 08:14 PM
Replies: 0
Views: 287
Posted By Bud
SWAP MEET Nov 3rd 2019 Brookville, OH

SWAP MEET at Brookville, OH, (Dayton area) sponsored by the Dayton-Buckeye Model A Club. At Reichard Chevrolet. Breakfast, Lunch, Inside and Outside Vendors. See Flyer for more details.
Forum: Early V8 (1932-53) 10-02-2019, 08:13 PM
Replies: 2
Views: 370
Posted By Bud
SWAP MEET Nov 3rd 2019 Brookville, OH

SWAP MEET at Brookville, OH, (Dayton area) sponsored by the Dayton-Buckeye Model A Club. At Reichard Chevrolet. Breakfast, Lunch, Inside and Outside Vendors. See Flyer for more details.
Forum: Model T (1909-1927) 10-02-2019, 08:06 PM
Replies: 0
Views: 362
Posted By Bud
SWAP MEET Nov 3rd 2019 Brookville, OH

SWAP MEET at Brookville, OH, (Dayton area) sponsored by the Dayton-Buckeye Model A Club. At Reichard Chevrolet. Breakfast, Lunch, Inside and Outside Vendors. See Flyer for more details.
Forum: Model A (1928-31) 10-02-2019, 08:02 PM
Replies: 1
Views: 222
Posted By Bud
Re: Swap Meet Nov 3rd 2019 Brookville, OH

SWAP MEET at Brookville, OH, (Dayton area) sponsored by the Dayton-Buckeye Model A Club. At Reichard Chevrolet. Breakfast, Lunch, Inside and Outside Vendors. See Flyer for more details.
Forum: Model A (1928-31) 10-02-2019, 07:51 PM
Replies: 1
Views: 222
Posted By Bud
Swap Meet Nov 3rd 2019 Brookville, OH

SWAP MEET at Brookville, OH, (Dayton area) sponsored by the Dayton-Buckeye Model A Club. At Reichard Chevrolet. Breakfast, Lunch, Inside and Outside Vendors. See Flyer for more details.
Forum: Model A (1928-31) 09-13-2019, 11:18 AM
Replies: 10
Views: 895
Posted By Bud
Re: Model a Coupe Roll up rear window

As I recall, the earlier coupes have a flange you have to cut off so the window can roll down. This is usually never mentioned when people discuss this conversion.
Forum: Model A (1928-31) 08-15-2019, 11:20 AM
Replies: 16
Views: 1,513
Posted By Bud
Re: Flared copper washers for gaskets?

You can get oversize ferrules for gas lines from both Bratton's (part #13491) and Snyder's (part # A-9244), both $7.95 a pair. A friend of mine makes them.
Forum: Model A (1928-31) 08-01-2019, 11:26 AM
Replies: 30
Views: 2,291
Posted By Bud
Re: misdiagnosis based on assumptions

Would a worn axle housing race have caused additional bending stress on the axle, promoting a fatigue failure?
Forum: Model A (1928-31) 07-27-2019, 08:22 AM
Replies: 0
Views: 239
Posted By Bud
Butler County Antique Car Parade Today

Anybody know the route the cars are taking from downtown Hamilton, OH, to Fairfield Crossings (Rte 4) at Symmes Rd?
Forum: Model-A 06-28-2019, 11:28 AM
Replies: 0
Views: 322
Posted By Bud
front half of Model A Frame

I am considering building an engine run-in stand and may use the front half of a Model A Frame to make it easier. Depends on the cost (in other words it has to be fairly inexpensive otherwise I can...
Forum: Model-A 06-26-2019, 10:37 PM
Replies: 3
Views: 1,286
Posted By Bud
Re: Model B Transmission & Adapter Kit

The adapters, motor mounts, and NOS cluster gear have been SOLD. A sale is pending on the transmission.
Forum: Model A (1928-31) 06-25-2019, 11:25 AM
Replies: 14
Views: 884
Posted By Bud
Re: BB truck distributor quesstion

If using a Model B distributor on a Model A with a Model A timing cover, can one use the B distributor as-is or does the distributor need to be modified in any way to get the proper advance?
Forum: Model A (1928-31) 05-14-2019, 11:15 AM
Replies: 19
Views: 1,805
Posted By Bud
Re: 28-29 gas caps gaskets

I found last night that if I cut a gasket out of 1/8" thick red rubber material and back it up with another of 1/16 thickness, I could not put it on the radiator. I then removed the 1/16th material...
Forum: Model A (1928-31) 05-13-2019, 11:18 AM
Replies: 19
Views: 1,805
Posted By Bud
Re: 28-29 gas caps gaskets

I forgot to mention that I am working on a 31 Fordor. This is the most recent radiator cap gasket thread I found, so I posted here.
Thanks.
Forum: Model A (1928-31) 05-12-2019, 07:35 PM
Replies: 19
Views: 1,805
Posted By Bud
Re: 28-29 gas caps gaskets

I am trying to seal up my radiator cap with a 1-3/8" x 2-1/2 x 1/8"" thick leather gasket. For one the 1-3/8" needs to be 1-1/2" which I fixed. But it still will not tighten properly. It is still...
Forum: Model-A 03-17-2019, 09:25 PM
Replies: 7
Views: 2,306
Posted By Bud
Forum: Model-A 03-17-2019, 09:24 PM
Replies: 1
Views: 436
Posted By Bud
Re: Visible Gas Pump For Sale--Milwaukee

Pump and all parts are SOLD.
Forum: Model-A 03-17-2019, 09:24 PM
Replies: 1
Views: 620
Posted By Bud
Re: Visible Gas Pump For Sale--Wayne 615

Pump and all parts are SOLD.
Forum: Model A (1928-31) 03-05-2019, 12:21 PM
Replies: 15
Views: 1,827
Posted By Bud
Re: Aussie Model A Ute

That's a pretty cute Ute!
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 05:16 AM.