Forum: Early V8 (1932-53)
08-22-2015, 03:41 PM
|
Replies: 4
Views: 1,154
Re: Remove crankshaft pulley
By gorry, Karl, that worked slick. Used an old Ford tire iron, hit it 4 or 5 times in about 3 places, not too hard, and it slid right ahead and the pan dropped right down.
Many thanks. Karl was...
|
Forum: Early V8 (1932-53)
08-22-2015, 02:46 PM
|
Replies: 4
Views: 1,154
|
Forum: Early V8 (1932-53)
08-22-2015, 11:23 AM
|
Replies: 4
Views: 1,154
|
Forum: Early V8 (1932-53)
08-22-2015, 11:03 AM
|
Replies: 4
Views: 1,154
|
Forum: Early V8 (1932-53)
02-09-2015, 04:37 PM
|
Replies: 7
Views: 1,056
Re: Some preliminary advice
Thank you, Davis J and Uncle Bub. I do remember reading something about the 3" and 3 1/4" difference but didn't recall where to measure. I'll check the throwout bearing area on the bell housing also....
|
Forum: Early V8 (1932-53)
02-09-2015, 04:31 PM
|
Replies: 7
Views: 1,056
Re: Some preliminary advice
Thanks a lot, MrBruce!
It's been snowing here since Saturday night and the temperature hasn't gone above 12 degrees. Fortunately not a lot of accumulation but enough snow in the face to last me...
|
Forum: Early V8 (1932-53)
02-08-2015, 08:11 PM
|
Replies: 7
Views: 1,056
|
Forum: Early V8 (1932-53)
02-08-2015, 06:15 PM
|
Replies: 7
Views: 1,056
Some preliminary advice
Before trying to start my '32 Fordor with a '36 motor, I want to drop the pan and clean it out, check the oil pump and see if it's really an LB (haven't found any letters stamped on the block under...
|
Forum: Early V8 (1932-53)
12-28-2014, 07:49 PM
|
Replies: 13
Views: 3,216
|
Forum: Early V8 (1932-53)
12-28-2014, 07:31 PM
|
Replies: 13
Views: 3,216
New vendor?
Has anybody dealt with Chris Talley Auto Spares in Magnolia, AR? If so, what
do you think?
Thanks,
Fred
|
Forum: Early V8
12-23-2014, 04:58 PM
|
Replies: 0
Views: 1,033
Needed for '32 Fordor
1. Long-hub fan, part #18-8600
2. Front seat runners
3. Any ideas on how to get ahold of these!
Thanks,
Fred
|
Forum: Early V8 (1932-53)
08-28-2014, 03:53 PM
|
Replies: 22
Views: 4,968
Re: 5w30?
Thanks, Kube. I'll spring for something thicker.
|
Forum: Early V8 (1932-53)
08-28-2014, 02:37 PM
|
Replies: 22
Views: 4,968
Re: 5w30?
Thanks to both of you - I'll go with fresher, thicker stuff.
|
Forum: Early V8 (1932-53)
08-28-2014, 12:25 PM
|
Replies: 22
Views: 4,968
5w30?
Being part Scot, I'd like to use some 5W30 oil that has been on the shelf for a while in a '36 engine (not a rebuild) that I've never run. Will that be acceptable or should I not be so frugal (notice...
|
Forum: Early V8 (1932-53)
07-29-2014, 03:41 PM
|
Replies: 19
Views: 2,128
|
Forum: Early V8 (1932-53)
07-17-2014, 07:40 PM
|
Replies: 19
Views: 2,128
|
Forum: Early V8 (1932-53)
07-17-2014, 04:05 PM
|
Replies: 19
Views: 2,128
|
Forum: Early V8 (1932-53)
07-17-2014, 02:13 PM
|
Replies: 19
Views: 2,128
|
Forum: Early V8 (1932-53)
07-17-2014, 01:20 PM
|
Replies: 19
Views: 2,128
|
Forum: Early V8 (1932-53)
07-17-2014, 11:49 AM
|
Replies: 19
Views: 2,128
Re: "Tis a puzzlement, at least to me
Thanks. Clutch in, everything rotates fine - from the rear wheel. But using the crank, still the same thud...thud. Seems a bit more metallic as the wheel moves forward and it seems to be louder on...
|
Forum: Early V8 (1932-53)
07-17-2014, 10:56 AM
|
Replies: 19
Views: 2,128
|
Forum: Early V8 (1932-53)
07-17-2014, 10:46 AM
|
Replies: 19
Views: 2,128
"Tis a puzzlement, at least to me
'36 engine: I thought it was frozen - until I jacked up a rear wheel and discovered that there is about 6" of wheel movement each way before it stops with a gentle thud.
Many thanks for your...
|
Forum: Early V8 (1932-53)
12-01-2013, 11:48 AM
|
Replies: 2
Views: 1,483
|
Forum: Early V8
11-01-2013, 09:31 AM
|
Replies: 4
Views: 1,026
Re: 32 Fordor seat runners
Haven't checked back for a while- I'll get some pictures of the upper part (attaches to the seat itself) which may give you an idea what the part that attaches to the floor looks like.
Thanks.
|
Forum: Early V8
09-21-2013, 11:09 AM
|
Replies: 4
Views: 1,026
32 Fordor seat runners
Does anyone have or know of a source for the floor part of the seat runners for a 1932 Fordor. Mac's replacements require a number of new holes in the floor which I'd rather not make.
Thanks for...
|