Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.04 seconds.
Search: Posts Made By: 34PKUP
Forum: Early V8 (1932-53) 11-12-2019, 08:35 PM
Replies: 13
Views: 601
Posted By 34PKUP
Re: What is it?

To prove or dis-prove the theory that the slot is for coins, see if all denominations of coins fit in the slot.
Forum: Early V8 (1932-53) 11-09-2019, 05:44 PM
Replies: 95
Views: 2,717
Posted By 34PKUP
Re: Ebay sales tax in place

If EBAY collected the tax then it's just a simple matter of presenting a proof of tax payment to the DMV. if the transaction is not already in the system,
And if EBAY does not collect tax on motor...
Forum: Early V8 (1932-53) 11-09-2019, 01:35 PM
Replies: 95
Views: 2,717
Posted By 34PKUP
Re: Ebay sales tax in place

Sellers don't pay sales tax, buyers pay sales tax.
When a local car dealer sells a car it's the buyers obligation to pay the sales tax (if any), not the dealer.
Forum: Early V8 (1932-53) 11-09-2019, 05:54 AM
Replies: 11
Views: 418
Posted By 34PKUP
Re: PCV process

When is the last time you have seen an 8BA Flathead Ford equipped with a Labyrinth rear seal? :confused:
Forum: Early V8 (1932-53) 10-30-2019, 09:24 AM
Replies: 29
Views: 1,316
Posted By 34PKUP
Re: Evolution of installing cylinder heads

Never had a problem using non hardening Permatex.
It never glued bolts/studs in position and never leaked after re-tightening.
Forum: Early V8 (1932-53) 10-28-2019, 06:54 PM
Replies: 4
Views: 401
Posted By 34PKUP
Re: Basket Case 50 Club Coupe

If the picture you show is after correcting, at least the passenger side appears to be wired correctly.
Forum: Early V8 (1932-53) 10-26-2019, 06:32 AM
Replies: 30
Views: 1,349
Posted By 34PKUP
Re: Mercury crank

Just curious, why is it necessary to take the time and effort to tap holes and insert threaded plugs? When the original Ford type plugs were used on literally millions of cranks (not hundreds)...
Forum: Early V8 (1932-53) 10-21-2019, 02:07 AM
Replies: 11
Views: 457
Posted By 34PKUP
Re: Power disc brakes 1950 ford f1

Perhaps if you contacted the seller of the product they would enlighten you.
Forum: Early V8 (1932-53) 10-18-2019, 07:57 AM
Replies: 4
Views: 290
Posted By 34PKUP
Re: Piston identification required

Parts book for Merc. pistons lists as (P/N EAC 6108)
If they are Ford pistons they would not be correct to use with Merc. crank.
Forum: Early V8 (1932-53) 10-17-2019, 01:23 AM
Replies: 7
Views: 348
Posted By 34PKUP
Re: Dipstick question

Obviously the wrong tube/indicator.
If when filled with 4 qts it's shy of the mark then just make a new mark at that point.
There is no reason to over fill it.
Forum: Early V8 (1932-53) 10-12-2019, 08:22 AM
Replies: 2
Views: 193
Posted By 34PKUP
Re: Low cranking voltage

One thing for sure is if you had a stock flathead in it, even on 12 volts you would not have the same problem.
Forum: Early V8 (1932-53) 10-11-2019, 02:13 PM
Replies: 11
Views: 602
Posted By 34PKUP
Re: Oil pan baffels ?

?? The pump intake has to be located in the sump no matter where the sump is located or what shape it is.
Forum: Early V8 (1932-53) 10-04-2019, 04:22 PM
Replies: 17
Views: 449
Posted By 34PKUP
Re: Upper radiator hose measurement

Unfortunately this is a wasted effort as the 'OP' needs something different as evidenced in post #7 above.
Forum: Early V8 (1932-53) 09-30-2019, 08:15 PM
Replies: 8
Views: 475
Posted By 34PKUP
Re: Disc trimer /cutter

Don't know what kind of discs you are talking about but the autobody surfacing discs that are being talked about generally have to have about a half inch or more removed to get to fresh material.
Forum: Early V8 (1932-53) 09-30-2019, 03:31 PM
Replies: 25
Views: 2,506
Posted By 34PKUP
Re: A Dennis Carpenter Complaint?? UPDATED!!!

For the most part I don't care to see peoples problems with vendors hashed out in this forum, BUT, in this case it does make sense to give a heads up.
Good grief, not only is the product picture not...
Forum: Early V8 (1932-53) 09-18-2019, 07:35 AM
Replies: 19
Views: 823
Posted By 34PKUP
Re: Head bolt washers

I have used (military spec) MS20002-7 flat washers in the past.
At the time they were about 10 each.
Forum: Early V8 (1932-53) 09-13-2019, 06:22 PM
Replies: 6
Views: 447
Posted By 34PKUP
Re: Installing bottom hoses in an aftermarket radiator

Seeing as you seem to know who the previous owner is, why don't you contact him to get the information?
Rather than seek information from anyone who has never seen your installation to visualize a...
Forum: Early V8 (1932-53) 09-11-2019, 05:52 AM
Replies: 6
Views: 281
Posted By 34PKUP
Re: 53 cussy Lower Control Arm Shaft

What is a '53 "cussy" :confused:
Forum: Early V8 (1932-53) 09-08-2019, 08:08 PM
Replies: 5
Views: 291
Posted By 34PKUP
Re: 226 G, anyone used a Petronixs on one?

Whether you have 12 volts or 6 volts is meaningless until you find out if there is indeed a conversion available for your flathead 6 cylinder engine.
Forum: Early V8 (1932-53) 09-08-2019, 12:41 PM
Replies: 17
Views: 947
Posted By 34PKUP
Re: What kind of air cleaner setup is this?

Seems obvious that it's a Canadian Mercury engine out of a '51 Canadian Monarch.
Forum: Early V8 (1932-53) 09-05-2019, 11:59 AM
Replies: 5
Views: 431
Posted By 34PKUP
Re: 39 Mercury question/mystery

I haven't seen it either but as previously stated pic. was probably taken using a mock-up non production car. (nothing to get exited about)
Forum: Early V8 (1932-53) 09-01-2019, 04:58 PM
Replies: 3
Views: 351
Posted By 34PKUP
Re: Tool ID

Sounds like any steering wheel puller I have ever owned but without a picture it's a wild guess.
Forum: Early V8 (1932-53) 08-31-2019, 07:26 AM
Replies: 10
Views: 402
Posted By 34PKUP
Re: Fitting a Fuel Pump

My advice, (and you probably won't like it ) is to get rid of the mismatched fuel pump stand/ oil filler and install the correct pump stand that will use the 10-1/16 long push rod that goes with that...
Forum: Early V8 (1932-53) 08-26-2019, 05:40 AM
Replies: 13
Views: 668
Posted By 34PKUP
Re: Mystery Door Handle

True, a magnet may not stick to some grades of stainless steel but it will also not stick to cast pot metal which the handle is most likely made of.
Forum: Early V8 (1932-53) 08-19-2019, 03:37 AM
Replies: 3
Views: 321
Posted By 34PKUP
Re: *7" GE Headlights*

Don't know what you are trying to achieve by looking for obsolete part number sealed beams that were not even part of the original '37 vehicle.
If it is 12 volt then just replace them with #6024...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 02:56 PM.