Forum: Early V8 (1932-53)
05-09-2020, 12:05 PM
|
Replies: 9
Views: 1,470
Re: 50 F1 Temp Gauge Malfunctioning
The wiring was correct even though thr sender with two wire connections is on the right side of engine. When I grounded the two wires together, the gauge needle went from "H" to "C". However, as...
|
Forum: Early V8 (1932-53)
05-07-2020, 12:56 PM
|
Replies: 9
Views: 1,470
Re: 50 F1 Temp Gauge Malfunctioning
The wiring schematic shows the temp sensor with 2 wiring terminals on the driver's (left) side of engine. Mine is located on the passenger (right) side of engine. Will this affect the temp gauge's...
|
Forum: Early V8 (1932-53)
05-06-2020, 07:30 PM
|
Replies: 9
Views: 1,470
50 F1 Temp Gauge Malfunctioning
The gauge needle stays on "H" while engine is cold, but the needle begins moving left when engine is started and stops about halfway between mid-point of gauge and “C.”. As engine warms up, the...
|
Forum: Early V8 (1932-53)
10-16-2018, 05:40 PM
|
Replies: 2
Views: 1,158
Re: Hood Latch Spring Attachment 1950 F1
Thanks for posting the picture. I agree that it should be easy to figure out how the spring is attached so that the handle returns to its correct position with adequate tension to prevent rattling. ...
|
Forum: Early V8 (1932-53)
10-15-2018, 07:21 PM
|
Replies: 2
Views: 1,158
Hood Latch Spring Attachment 1950 F1
I need help positioning the hood latch spring that comes with the Hood Latch Mounting Pin Kit for a 1950 F1 (Part # 7C-16897-KIT). So far I have been unsuccessful and wondered if someone who owns a...
|
Forum: Early V8 (1932-53)
05-02-2014, 06:39 PM
|
Replies: 6
Views: 2,000
Early 1950 F-1 Pickup
Hi folks,
Does the speedometer cable go on top or behind the firewall insulation inan early 1950 F-1 Pickup?
Thanks for your help!
Joe
|
Forum: Early V8
12-09-2013, 04:43 PM
|
Replies: 0
Views: 583
original choke cable
I need an original choke cable for an early 1950 F-1. My original cable had a chrome piece that fit against the dash behind the knob, and the cable was secured by clip behind the dash. The chrome is...
|
Forum: Early V8
05-21-2013, 06:47 AM
|
Replies: 0
Views: 820
Inner fenders
I need both inner fenders for an early 1950 F-1 pickup truck. You may message me on this site or call me at 864-882-2139. Thanks for your help.
Joe
|
Forum: Early V8
04-05-2013, 02:15 PM
|
Replies: 6
Views: 5,312
Re: 48-52 F1/F2 Parts (Trailer Full)
Is the radiator shroud original and in good condition? I didn't know 1948-50 F-1's came with a shroud. Is the lower grill valance in good condition? Would you take $150 for the shroud, valance, and...
|
Forum: Early V8 (1932-53)
02-19-2013, 02:07 PM
|
Replies: 3
Views: 915
Radiator help
Has anyone purchased a radiator from LMC Truck? If so, what is the quality and who manufactures their radiators? I have contacted several dealers, and it seems that US Radiator manufactures radiators...
|
Forum: Early V8
12-05-2012, 09:10 PM
|
Replies: 1
Views: 1,367
|
Forum: Early V8
12-05-2012, 06:43 PM
|
Replies: 15
Views: 2,397
|
Forum: Early V8
12-05-2012, 01:23 PM
|
Replies: 1
Views: 1,138
Re: v8 parts
A=Model Man,
Do you still have the 48-50 pick-up fenders and top panel connector?
Thanks,
Joe Toler
|
Forum: Early V8
12-04-2012, 10:51 PM
|
Replies: 5
Views: 2,155
|