Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.06 seconds.
Search: Posts Made By: Kevin in NJ
Forum: Model A (1928-31) 03-15-2018, 09:38 AM
Replies: 12
Views: 1,628
Posted By Kevin in NJ
Re: Those $2 carbs from IOLA--original jets ! !

Not too long ago I used the info from Vince Falter's website to flow test a large quantity of jets. I used the Ford column length and Ford data.

I found most of the jets were flowing more then...
Forum: Model A (1928-31) 03-13-2018, 07:17 AM
Replies: 14
Views: 665
Posted By Kevin in NJ
Re: Six volt vs. twelve volt wiring


That is voltage equal current times resistance.
A heavier cable is needed to carry more current. At a higher voltage you need less current to flow so you can get away with thinner wires....
Forum: Model A (1928-31) 03-10-2018, 08:07 AM
Replies: 16
Views: 753
Posted By Kevin in NJ
Re: Water pump sealed bearings instead of packing.

I have seen some leakless pumps start leaking. It is easy enough to have a leakless pump also with the original type seal. Seems like the best solution in my book. Have it all packed and ready to go...
Forum: Model A (1928-31) 03-08-2018, 07:06 AM
Replies: 7
Views: 600
Posted By Kevin in NJ
Re: Why Use 'B' Camshaft?

It should be noted if you intend to switch to a B cam you also must change to wider head tappets.
Forum: Model A (1928-31) 03-04-2018, 07:43 AM
Replies: 9
Views: 384
Posted By Kevin in NJ
Re: Round speedometer adjustment/calibration ?

My experience on a couple of speedo's. I made a RPM counter with some electronics and on Bob's website (already listed) there was a chart for some speeds and rpm's.

I just moved the magnet shade...
Forum: Model A (1928-31) 02-28-2018, 01:12 PM
Replies: 11
Views: 559
Posted By Kevin in NJ
Re: Engine quit ------ Condenser overheated

Go over to the Mustang boards and you will find guys complaining about the new caps. They are sourced from china and the QC is not so good, this is for even the 'better' brands.

Get the A&L where...
Forum: Model A (1928-31) 02-28-2018, 06:45 AM
Replies: 25
Views: 1,011
Posted By Kevin in NJ
Re: Whatever happened to the surface mail option?

And if they got in the 2000's they would have electronic copies like other clubs.

The Mustang club has all back issues online and you have the option to read online/ download the magazine.
Forum: Model A (1928-31) 02-26-2018, 08:37 AM
Replies: 44
Views: 2,351
Posted By Kevin in NJ
Re: Making A parts with lathe

Custom bushings for the steering sector output was one case.

The bushings they sell do not seem large enough, at least the ones I bought, for new sector shaft. That is the sector shaft fit in...
Forum: Model A (1928-31) 02-18-2018, 03:35 PM
Replies: 2
Views: 365
Posted By Kevin in NJ
Minor Follow up: Point New and Old

My brother (Kurt in NJ) has a dist machine. So we wanted to double check what we knew about points. We also hope to fix some bad information. At a later point in time we may create a fact based...
Forum: Model A (1928-31) 02-17-2018, 07:28 AM
Replies: 19
Views: 1,228
Posted By Kevin in NJ
Re: Sometimes I get tired of it

My brother being a professional mechanic has has to deal with just about everything in his 40+ years. So I have some extra knowledge on taking stuck bolts out.

The basic fact is a fastener that is...
Forum: Model A (1928-31) 02-14-2018, 03:48 PM
Replies: 42
Views: 1,223
Posted By Kevin in NJ
Re: 1930 Brakes

First step is to take the drums off and look.

Where are the shoes touching, how much of the shoes are touching?

If the shoes are not centered or arched to fit the drums then you will never have...
Forum: Model A (1928-31) 02-12-2018, 03:49 PM
Replies: 33
Views: 1,426
Posted By Kevin in NJ
Re: Why no lock-washers?

Two thoughts..

First as mentioned, the heat cycling and the type of metal used for a lock washer would not work.

Second, not needed. I would guess that Ford used tight tolerance threading here...
Forum: Model A (1928-31) 02-12-2018, 06:54 AM
Replies: 12
Views: 826
Posted By Kevin in NJ
Re: what tool do I need to install hood corners

I used the kick riveter that have for doing brake shoes. It is a 2 person job.
Forum: Model A (1928-31) 02-11-2018, 09:19 PM
Replies: 8
Views: 352
Posted By Kevin in NJ
Re: 1930 rumble seat original but rubber pads too big

As I understand it the originals were too big and cut to fit at the factory, but I could be wrong.

In any event,

You want to fit them because I am sure today there is more variation on fit than...
Forum: Model A (1928-31) 02-10-2018, 07:34 AM
Replies: 16
Views: 874
Posted By Kevin in NJ
Re: A shock (ing) question

If you are driving you car without shocks and it feels safe above 25 MPH then you need to think about your springs first. Either they are wore out (front spring) or not lubricated very good.

Forum: Model A (1928-31) 02-08-2018, 01:03 PM
Replies: 6
Views: 1,052
Posted By Kevin in NJ
Re: A girl can dream...

Here is an interesting thought.

The Tesla will not last long. The organic (carbon based) structure such as the plastic dash and the carbon fiber 'frame' will fall apart. The cosmic radiation will...
Forum: Model A (1928-31) 02-08-2018, 12:57 PM
Replies: 6
Views: 296
Posted By Kevin in NJ
Re: 1931 Cabriolet Top info

Something to note about the above pictures. I am NOT saying this car is bad, but truth is you can not get the right windlace.

This car was done with the normal wind lace which is nailed in the...
Forum: Model A (1928-31) 02-07-2018, 08:25 AM
Replies: 7
Views: 480
Posted By Kevin in NJ
Re: Cabriolet

The sport coupe is a coupe body without the top.

The coupe and cabriolet are totally different bodies with no real interchangeable sheet metal (well some of the cowl).

The coupe is a metal...
Forum: Model A (1928-31) 02-04-2018, 07:36 AM
Replies: 23
Views: 1,612
Posted By Kevin in NJ
Re: How Did Henry Do It?

Super accurate production.

The bearings he used were likely held to a very very tight standard during production. The ones you buy today are not as accurate to as many decimal places.

He paid...
Forum: Model A (1928-31) 01-31-2018, 03:41 PM
Replies: 13
Views: 644
Posted By Kevin in NJ
Re: getting doors to fit correctly

The turnbuckle is a structure piece and is not for adjusting the body. The take the force of the top and keep the top from ripping the car apart. When the cowl moves it creates a lot of force at the...
Forum: Model A (1928-31) 01-31-2018, 03:36 PM
Replies: 26
Views: 1,068
Posted By Kevin in NJ
Re: 19" Rim's

Rust, spokes are not easy to make level. Mine had a few gouges. Rust inside the rim where the tire mount can be an issue.

While not a show stopper, take along a a good lugnut. Put it in the holes,...
Forum: Model A (1928-31) 01-26-2018, 01:23 PM
Replies: 18
Views: 945
Posted By Kevin in NJ
Re: permanent fix for doors

The turnbuckles on the cabriolet are structural and used to keep the body from beating itself to death. They are NOT for adjusting the position of anything!!!

The body should be considered a...
Forum: Model A (1928-31) 01-25-2018, 10:06 PM
Replies: 66
Views: 5,086
Posted By Kevin in NJ
Re: The Restorer needs to fact check its articles!!!

This comes back to some of my original points.

The editors job is to make sure the article is correct. If the editor is not familiar he should pass it on to technically proficient people to...
Forum: Model A (1928-31) 01-25-2018, 09:19 AM
Replies: 66
Views: 5,086
Posted By Kevin in NJ
Re: The Restorer needs to fact check its articles!!!

Please read and think before you write!!!!

I have not said the modern points are junk. The are not needed and the new plate is not as accurately made like the factory plate. It is a solution to a...
Forum: Model A (1928-31) 01-24-2018, 03:51 PM
Replies: 66
Views: 5,086
Posted By Kevin in NJ
Re: The Restorer needs to fact check its articles!!!

I have contacted editors and talked to upper level officers in years past.

I brought it up here because it still keeps happening. I felt some comments needed to be made on this board about this...
Showing results 1 to 25 of 500

Forum Jump
Sponsored Links (Register now to hide all advertisements)

All times are GMT -5. The time now is 10:43 AM.