Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 121
Search took 0.01 seconds.
Search: Posts Made By: Nasukau
Forum: Model A (1928-31) 04-18-2021, 11:26 PM
Replies: 4
Views: 307
Posted By Nasukau
Re: Wood Block Question 31 CCP

Building full fendered pickup with aprons. I would expect 1/4” to 1/2” gap. But not 1”.

Denny
Forum: Model A (1928-31) 04-18-2021, 01:15 PM
Replies: 4
Views: 307
Posted By Nasukau
Wood Block Question 31 CCP

Hi All,
With the wood blocks installed for a 31 CCP roughly how much of a gap is there from the bottom of the cab to the top of frame. The gap with the wood block installed is between for me is 3/4”...
Forum: Model A (1928-31) 03-30-2021, 11:10 PM
Replies: 2
Views: 382
Posted By Nasukau
Re: Part Name

Thank you Steve!

Denny
Forum: Model A (1928-31) 03-30-2021, 09:31 PM
Replies: 2
Views: 382
Posted By Nasukau
Part Name

Hi All,
Could someone please tell me what the part name is for the removable piece on the upper door jam is called. Please seethe attached pictures.

Thank you,
Denny
Forum: Model A (1928-31) 03-29-2021, 03:02 PM
Replies: 5
Views: 521
Posted By Nasukau
Re: 1931 CCP Seat Spring

Thanks for the replies. I contacted Don at Snyders and he is making up a pair for me!


Denny
Forum: Model A (1928-31) 03-26-2021, 01:02 PM
Replies: 5
Views: 521
Posted By Nasukau
1931 CCP Seat Spring

Hi All,
My seat spring for my 1931 CCP is missing the clips that snap into the seat riser. Picture attached of what is missing. Looking for ideas or alternatives that people have done to hold the...
Forum: Model A (1928-31) 01-12-2021, 10:16 PM
Replies: 20
Views: 1,059
Posted By Nasukau
Re: Wide bed A pickup

Here is a picture of the bottom that someone had provided for me.

Denny
Forum: Model A (1928-31) 01-11-2021, 10:08 AM
Replies: 8
Views: 644
Posted By Nasukau
Re: Replacement Running Board Bolt Bracket

Thanks everyone for the responses and advice.

Denny
Forum: Model A (1928-31) 01-09-2021, 08:18 PM
Replies: 8
Views: 644
Posted By Nasukau
Replacement Running Board Bolt Bracket

Hi All,
Does someone make a replacement bolt attachment(not sure of correct name) that is on the bottom of the running board where the bolt slides into to secure the running board to the running...
Forum: Model A (1928-31) 12-05-2020, 06:54 PM
Replies: 10
Views: 643
Posted By Nasukau
1931 Wide Bed Fender Question

Hi All,
I have a 1931 wide bed pickup and I am wondering if the small bed fenders would fit on a wide bed? The correct wide bed fenders are hard to find not to mention pricey and I donít really want...
Forum: Model A (1928-31) 11-02-2020, 09:56 AM
Replies: 7
Views: 678
Posted By Nasukau
Re: S/W Windshield Frame Installation

@160B the link from Brattons is exactly what I have. I just wanted to make sure that was all I needed. It didn’t look like it was correct for the hinge.

@ Art thank you for the drawing.

Denny
Forum: Model A (1928-31) 11-01-2020, 10:16 PM
Replies: 7
Views: 678
Posted By Nasukau
S/W Windshield Frame Installation

Hi All,
When installing the windshield frame is there a different gasket for a S/W that goes between the wood header and frame hinge? I ordered a frame & hinge gasket for a S/W but it just doesnít...
Forum: Model A (1928-31) 10-06-2020, 09:28 PM
Replies: 6
Views: 551
Posted By Nasukau
Re: Lining up UJ and Diveshaft splines, any tips?

String around the u-joint to not smash fingers. Wheels off the ground and spin tires until the driveshaft starts to slides in. Pull string out and finish mating the two together.

Denny
Forum: Model A (1928-31) 09-29-2020, 07:54 PM
Replies: 3
Views: 335
Posted By Nasukau
Re: Screw Size for 1931 Windshield Filler Trim

Late 1931 Budd Pickup with indented firewall.

Thank you,
Denny
Forum: Model A (1928-31) 09-29-2020, 03:59 PM
Replies: 3
Views: 335
Posted By Nasukau
Screw Size for 1931 Windshield Filler Trim

Hi All,
Does anyone know the screw size/thread of a 1931 windshield filler trim?

Thank you,
Denny
Forum: Model A (1928-31) 09-15-2020, 11:29 PM
Replies: 2
Views: 338
Posted By Nasukau
Re: S/W How to Disassemble Windshield Frame

Thank you Bob! Those were excellent videos. Just what I needed to see.

Denny
Forum: Model A (1928-31) 09-15-2020, 08:02 PM
Replies: 2
Views: 338
Posted By Nasukau
S/W How to Disassemble Windshield Frame

Hi All,
Could someone please explain how the S/W windshield frame comes apart so I can remove the glass and get it ready to install the new glass. I have removed the two small screws from each side...
Forum: Model A (1928-31) 05-05-2020, 10:17 AM
Replies: 13
Views: 1,042
Posted By Nasukau
Re: Borg Warner Overdrive Lock Out

Thanks for the information Speedyal

Denny
Forum: Model A (1928-31) 05-05-2020, 09:09 AM
Replies: 13
Views: 1,042
Posted By Nasukau
Re: Borg Warner Overdrive Lock Out

Thanks Rotorwrench. I was thinking the same answer you provided. But I needed someone to confirm it to ease my mind.

Denny
Forum: Model A (1928-31) 05-04-2020, 11:39 PM
Replies: 13
Views: 1,042
Posted By Nasukau
Borg Warner Overdrive Lock Out

Hi All,
I installed a Borg Warner overdrive in my coupe. All that is left is to run the wires and the cable. Currently the lock out is pointed towards the back of the car. Please see the attached...
Forum: Model A (1928-31) 02-15-2020, 11:34 AM
Replies: 5
Views: 778
Posted By Nasukau
Re: Front Windshield Frame Screw Size

Thanks everyone.
Denny
Forum: Model A (1928-31) 02-13-2020, 12:24 AM
Replies: 5
Views: 778
Posted By Nasukau
Forum: Model A (1928-31) 02-09-2020, 07:19 PM
Replies: 5
Views: 778
Posted By Nasukau
Front Windshield Frame Screw Size

Hi All,
I am looking for the size and thread type for a front windshield of 31 CCPU


Thank you,
Denny
Forum: Model A (1928-31) 01-09-2020, 02:26 PM
Replies: 37
Views: 3,501
Posted By Nasukau
Re: Early 30 Pickup questions

That pickup body is beautiful the way it is! Heck just make sure it is safe to drive and then start enjoying all the time you get with your father and that pickup cruising around.


Denny
Forum: Model A (1928-31) 12-23-2019, 12:15 AM
Replies: 4
Views: 647
Posted By Nasukau
Re: 31 Pickup Top Wood Question

Thanks everyone for the responses.

Denny
Showing results 1 to 25 of 121

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 01:15 PM.