Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.05 seconds.
Search: Posts Made By: 35fordtn
Forum: Early V8 (1932-53) Yesterday, 09:13 PM
Replies: 4
Views: 315
Posted By 35fordtn
Re: Anyone know what year and model they are

1935-36 Ford convertible sedan rear window regulators.
Forum: Early V8 (1932-53) Yesterday, 07:33 PM
Replies: 4
Views: 195
Posted By 35fordtn
Re: 1936 Windshield regulator searched

We've still got a "New" drake one in stock... only one.
Forum: Early V8 (1932-53) Yesterday, 07:06 PM
Replies: 2
Views: 184
Posted By 35fordtn
Re: Flywheel on a 21 stud

As long as you are not using a 32-34 transmission case it will work just fine.
Forum: Early V8 (1932-53) Yesterday, 07:04 PM
Replies: 14
Views: 336
Posted By 35fordtn
Re: 1941 Ford pickup seat

This sounds like a excellent idea Mike, I am too much a purist to install a van seat but my 36 pickup is very uncomfortable.. .
Forum: Early V8 (1932-53) Yesterday, 06:59 PM
Replies: 21
Views: 470
Posted By 35fordtn
Re: Pressure plate finger adj

I have had a total of 3 issues of FT Wayne Clutches over the few years I have been into this hobby out of maybe 25 of their units.. I personally do not use them anymore, but the issues I have had...
Forum: Early V8 (1932-53) Yesterday, 04:55 PM
Replies: 21
Views: 470
Posted By 35fordtn
Re: Pressure plate finger adj

Well My experiences are real.. And I ran into this twice in the last year. One instance was just two weeks ago. I had a 36 Ford in the shop with a Fort Wayne Clutch that was WAY off. They tack...
Forum: Early V8 (1932-53) 07-02-2020, 06:36 PM
Replies: 46
Views: 1,442
Posted By 35fordtn
Re: Pat McFarlane RIP

Jeff,
that's a excellent photo. Likely not long (couple hours) after that photo, Pat gave me a ride in his 32 to pick u a part he bought from me. My daughter was with us. He paid me the small...
Forum: Early V8 (1932-53) 07-02-2020, 10:36 AM
Replies: 3
Views: 172
Posted By 35fordtn
Re: Front galley plug

As the above poster stated, I asked this on here not long ago with the same answer he gave

For visualization here is what they look like
...
Forum: Early V8 (1932-53) 07-02-2020, 09:08 AM
Replies: 46
Views: 1,442
Posted By 35fordtn
Re: Pat McFarlane RIP

Im gonna miss pat. He was always very good to me and my family.
Forum: Early V8 (1932-53) 07-01-2020, 07:26 PM
Replies: 9
Views: 558
Posted By 35fordtn
Re: Dizzy days

We sell them out right, or the best (Cheapest) option is send yours in and usually 2-5 days later its on it's way back to you.
Forum: Early V8 (1932-53) 07-01-2020, 04:20 PM
Replies: 24
Views: 1,292
Posted By 35fordtn
Re: Latest bubba report

Jim,
Glad you are doing well, and enjoying building a car. Have fun thats what life's all about. Your a good honest man.
Forum: Early V8 (1932-53) 07-01-2020, 01:48 PM
Replies: 9
Views: 558
Posted By 35fordtn
Dizzy days

One of my part timers has really gotten good with distributors, transmissions, and fuel pumps. He builds / restores them and gets all the metal pieces prepped for plating and I set them up.

...
Forum: Early V8 (1932-53) 06-30-2020, 10:17 PM
Replies: 12
Views: 411
Posted By 35fordtn
Re: help finding a ring gear

We've got a NOS one sitting here on the shelf....
Forum: Early V8 (1932-53) 06-26-2020, 09:39 PM
Replies: 17
Views: 1,423
Posted By 35fordtn
Re: Uncommon '34 clock

I do believe this is the holy grail of Early Ford factory accessories.. in my opinion at least. Due to the rarity of them I dont know the current values... but seven years ago I sold a NOS one (that...
Forum: Early V8 (1932-53) 06-25-2020, 04:51 PM
Replies: 19
Views: 1,163
Posted By 35fordtn
Re: NOS parts

Bob Jones is a dear mentor and friend of mine since I've been in the hobby and I wish him the best!

David is correct, I can assure the chances of my little business acquiring the inventory is...
Forum: Early V8 (1932-53) 06-24-2020, 07:19 PM
Replies: 24
Views: 821
Posted By 35fordtn
Re: 34 Issues Ongoing -Video

Karl,
When you get fed up enough, I'll take the car off your hands!!

All jokes aside if I wasn't thousands of miles away I'd come over and help.
Forum: Early V8 (1932-53) 06-24-2020, 07:12 PM
Replies: 24
Views: 821
Posted By 35fordtn
Re: 34 Issues Ongoing -Video

Carl,
Do you have another pump? Maybe that pump is pushing too much pressure for the type needle and seat your carb has. Maybe test the needle and seat and lower the float level down a touch???
...
Forum: Early V8 (1932-53) 06-24-2020, 12:12 AM
Replies: 24
Views: 821
Posted By 35fordtn
Re: 34 Issues Ongoing -Video

Karl I can see in the video the choke is pulled a good bit. I presume it does the same with the choke open?

Have you check the plugs after it does to see if maybe it is flooding itself?

...
Forum: Early V8 (1932-53) 06-23-2020, 10:29 PM
Replies: 4
Views: 261
Posted By 35fordtn
Re: inner cap to rotor gap

No more than .020 IMO. With a good coil on my sun machine experimenting, Ive witnessed a excellent spark at a plug with up to .035.


Sent from my iPhone using Tapatalk
Forum: Early V8 (1932-53) 06-23-2020, 07:33 PM
Replies: 21
Views: 693
Posted By 35fordtn
Re: Classic condenser failure?

took me a while to figure out, but I am 99.9% certain the three letters are a code to identify the date it was rebuilt. Pretty smart if you ask me.
Forum: Early V8 (1932-53) 06-23-2020, 02:22 PM
Replies: 21
Views: 693
Posted By 35fordtn
Re: Classic condenser failure?

HAI, means it is a skip coil that he rebuilt August,2019.
Forum: Early V8 (1932-53) 06-19-2020, 06:37 PM
Replies: 6
Views: 266
Posted By 35fordtn
Re: 38-41 Pickup Body to Frame Bolts

The original springs have a rate of 880 lbs, so they should move much under normal driving conditions.
Forum: Early V8 (1932-53) 06-17-2020, 09:47 PM
Replies: 13
Views: 590
Posted By 35fordtn
Re: LB block repairable (or can it be)?????

I disagree, A set of Main bearings is $160 A babbit job will cost MUCH more than that. Aside from that cost, I would use either with no hesitation...
Forum: Early V8 (1932-53) 06-16-2020, 10:46 PM
Replies: 21
Views: 988
Posted By 35fordtn
Painting nuts and bolts...

As another note most black oxide platers have a minimal $50 charge and $1.00 a pound after the first fifty. Two cans of decent rattle can paint would cost you close to that.

I send stuff off...
Forum: Early V8 (1932-53) 06-16-2020, 08:53 PM
Replies: 21
Views: 988
Posted By 35fordtn
Re: Painting nuts and bolts...

When in a pinch I use John Deere muffler black. Some of the best satin black spray paint I've ever used...

https://www.ebay.com/itm/John-Deere-Muffler-Black-Spray-Paint-TY25657/362866990575
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:19 PM.