Forum: Early V8 (1932-53)
03-01-2019, 01:37 PM
|
Replies: 5
Views: 1,227
48 ford f1 complete bed replacement
Has anyone replaced their bed assembly on a 48-50f1? I am looking for a new period correct entire bed and fenders,brand new.I have looked ate Dennis carpenter,Lmc,and alot of eBay listings.Some offer...
|
Forum: Early V8 (1932-53)
02-28-2018, 05:43 AM
|
Replies: 2
Views: 2,005
48 ford 226h flathead 6
Good morning,can you tell me the correct valve lash settings for this motor? My book has 2 listings,they are .010 .014 .017 .019 ?Also it does not say hot or cold setting,let me know ,thanks
|
Forum: Questions & Suggestions
10-14-2017, 05:06 AM
|
Replies: 2
Views: 2,194
Torqometer tq-150 snap on
I just picked up this 50's vintage torque wrench.The plastic dial cover is all yellow and pitted,.Does anyone know how to remove the dial cover?
|
Forum: Early V8 (1932-53)
05-17-2017, 10:45 AM
|
Replies: 5
Views: 2,064
Re: 48 f1 226 h 6cyl
Thanks,I found out if I jack up the truck,take off passenger side tire.Inside the fender well there are 6-8 bolts that separate the fenderwell.You have a straight shot at all valves,once you remove...
|
Forum: Early V8 (1932-53)
05-16-2017, 02:14 PM
|
Replies: 5
Views: 2,064
48 f1 226 h 6cyl
I was wondering if anyone knows the proper procedure to adjust valve tappets on a running vechicle .My 48 ford f1 226h has approx 900 miles since rebuild.The tappets need adjusting to quiet them...
|
Forum: Early V8 (1932-53)
01-21-2017, 05:58 AM
|
Replies: 2
Views: 1,021
|
Forum: Early V8 (1932-53)
01-20-2017, 03:16 PM
|
Replies: 2
Views: 1,021
48 f1 4speed shifter boot
Hey fellas,Would anyone know where I can locate a floor shift boot for this 4 speed floor shift? I am told it's different and bigger than the 3 speed,any help would be good,Thanks
|
Forum: Early V8 (1932-53)
01-18-2017, 06:02 PM
|
Replies: 4
Views: 1,650
|
Forum: Early V8 (1932-53)
01-17-2017, 05:31 PM
|
Replies: 4
Views: 1,650
48 ford f1 226 h spark plug wire set
I am trying to locate a good set of plug wires for this 48 f1 226h.I have been searching and found these part numbers.7HA12259 No boot and B1a-12259a with boot for 51 car.I already have the brown...
|
Forum: Early V8 (1932-53)
12-31-2016, 03:34 PM
|
Replies: 20
Views: 4,142
|
Forum: Early V8 (1932-53)
12-31-2016, 01:05 PM
|
Replies: 20
Views: 4,142
Re: 48 ford f1 226 h ethanol rebuild kit
I have not found a new fuel pump that is Ethanol tolerant everyone just sells cheap pumps around 50.00 they only last 1yr and leak,if you have a source for upgrade fuel pump ,please let me...
|
Forum: Early V8 (1932-53)
12-31-2016, 01:01 PM
|
Replies: 20
Views: 4,142
|
Forum: Early V8 (1932-53)
12-30-2016, 03:00 PM
|
Replies: 20
Views: 4,142
|
Forum: Early V8 (1932-53)
12-30-2016, 06:59 AM
|
Replies: 20
Views: 4,142
|
Forum: Early V8 (1932-53)
12-29-2016, 05:26 PM
|
Replies: 20
Views: 4,142
|
Forum: Early V8 (1932-53)
12-29-2016, 05:24 PM
|
Replies: 20
Views: 4,142
|
Forum: Early V8 (1932-53)
12-29-2016, 03:12 PM
|
Replies: 20
Views: 4,142
48 ford f1 226 h ethanol rebuild kit
I am trying to locate an Ethanol carb kit for my Ford 8HA -1 barrel carb. I am told the diaphragm is made out of a special material that Ethanol fuel won't deteriorate ,has any had any luck in...
|
Forum: Early V8 (1932-53)
12-29-2016, 03:07 PM
|
Replies: 7
Views: 1,677
|
Forum: Early V8 (1932-53)
12-29-2016, 03:06 PM
|
Replies: 7
Views: 1,677
|
Forum: Early V8 (1932-53)
12-29-2016, 05:33 AM
|
Replies: 7
Views: 1,677
|
Forum: Early V8 (1932-53)
12-28-2016, 05:31 PM
|
Replies: 7
Views: 1,677
48 ford f1 gas cap
Does anyone know what is the OEM Gas cap for this truck?.The tank is mounted inside cab behind the seat.Is it vented or non vented,my book does not say. Thanks
|
Forum: Early V8 (1932-53)
12-05-2016, 10:44 AM
|
Replies: 23
Views: 5,376
|
Forum: Early V8 (1932-53)
12-04-2016, 05:50 PM
|
Replies: 23
Views: 5,376
Re: 6 volt gauges
I see that very clearly,one side to middle circuit breaker,other side to negative post on solenoid. These 1947 gauges are they the same ones that will fit my 1948 f1 6v? The reason I ask is a...
|
Forum: Early V8 (1932-53)
12-04-2016, 05:43 PM
|
Replies: 23
Views: 5,376
|
Forum: Early V8 (1932-53)
12-04-2016, 02:03 PM
|
Replies: 23
Views: 5,376
Re: 6 volt gauges
My battery and solenoid are on the drivers side,I am confused by drawing as to properly route wire,should drawing be flipped?
|