Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.08 seconds.
Search: Posts Made By: G.M.
Forum: Early V8 (1932-53) 10-18-2020, 08:28 PM
Replies: 3
Views: 183
Posted By G.M.
Re: 1937-1941 Pickup Box Bolts

You can buy any shape or length of bolts from McMaster-Carr
or Grainger. They come in steel or Stainless I always use SS
G.M.
Forum: Early V8 (1932-53) 10-17-2020, 11:35 AM
Replies: 14
Views: 528
Posted By G.M.
Re: 33 Tranny to Driveshaft Oil Leak

FILL the U joint with at last a tube of high drop or drip point
grease. This stays stiff to make a seal and softens up as the
temperature from transmission heats up. G.M.
Forum: Early V8 (1932-53) 10-13-2020, 02:08 PM
Replies: 10
Views: 500
Posted By G.M.
Re: Mohawk lifts

I bought 2 over 25 years ago. No problems and still
work good. I bought them out of Miami. G.M.
Forum: Early V8 (1932-53) 10-10-2020, 03:34 PM
Replies: 3
Views: 326
Posted By G.M.
Re: 1933-34 battery box

Here is a good place for your optima battery. Make a little box
with vent holes. This box can also be mounted on the frame
near the starter, if I find the picture I will post it. G.M.
Forum: Early V8 (1932-53) 10-06-2020, 11:57 AM
Replies: 12
Views: 486
Posted By G.M.
Re: Ford V belts - 39-38

There is a very large hardware store in Ephrata, Pa. named Zimmerman's.
Hanging on the ceiling is about 10 or 12 rows of V belts. Each row is about
75 feet long. There are many different types of...
Forum: Early V8 (1932-53) 10-03-2020, 09:54 PM
Replies: 2
Views: 375
Posted By G.M.
Re: Swap Meet FORD Tool??

Looks like shackle bushing tool to me. G.M.
Forum: Early V8 (1932-53) 09-16-2020, 11:15 AM
Replies: 15
Views: 690
Posted By G.M.
Re: 1936 Overheating Problem

Skip Makes new impellers for the 32 to 36 pumps. They are a little
larger in diameter, The fins are longer. The pump has to be bored
out a little which gives more coolant flow. G.M.
Forum: Early V8 (1932-53) 09-14-2020, 09:04 PM
Replies: 11
Views: 399
Posted By G.M.
Re: Water pump repair

They do come primed, ready to paint your color. G.M.
Forum: Early V8 (1932-53) 08-24-2020, 07:30 AM
Replies: 7
Views: 390
Posted By G.M.
Re: Battery Tender light vs Ammeter query

You can run an Optima too low and something happens it won't take a charge.
You have to connect it to a strong battery and charge it and it comes back to
life. I think that is the procedure. They...
Forum: Early V8 (1932-53) 08-23-2020, 12:41 PM
Replies: 14
Views: 819
Posted By G.M.
Re: Mice in the rear quarter

How about a Furret? G.M.
Forum: Early V8 (1932-53) 08-21-2020, 12:52 PM
Replies: 27
Views: 1,077
Posted By G.M.
Re: 1940 fan shroud

Jay that deflector is not going to help. The only thing that helps is more
air flow. A fan blade with more blades at a steeper pitch really improve cooling at idle and stop and go speeds. These...
Forum: Early V8 (1932-53) 08-19-2020, 11:03 AM
Replies: 19
Views: 646
Posted By G.M.
Re: Question about a "Helmet" distributor

Search back in this forum, I put a detailed method
for testing condensers. Almost all of them test good
cold but need to be heated to over 200 degrees, hot
is when they breakdown. G.M.
Forum: Early V8 (1932-53) 08-17-2020, 08:47 AM
Replies: 27
Views: 1,367
Posted By G.M.
Re: helmet distributor

Skip in Florida does the Stock type Ford Helmet Distrs. He has done
them for 25 years and does 4 or 5 every day. He uses the original
Ford~Heyer strobe machine that all the ford dealers and machine...
Forum: Early V8 (1932-53) 08-07-2020, 12:01 PM
Replies: 56
Views: 2,187
Posted By G.M.
Re: Generator or alternator ?

GM alternators work great. Just have a 24 volt stator
installed and it will charge at idle with a small stock
Ford pulley. G.M.
Forum: Early V8 (1932-53) 08-06-2020, 01:33 PM
Replies: 14
Views: 737
Posted By G.M.
Re: Shocks are bottomed out

Get your spring re arched. G.M.
Forum: Early V8 (1932-53) 08-06-2020, 01:30 PM
Replies: 7
Views: 567
Posted By G.M.
Re: Is there a FANdemic going on????

While looking through Schramm's attic a number of years
ago I found a pile of industrial blades. They were thick metal
and some were pushers and some normal pullers. I made
adaptors for a few and...
Forum: Early V8 (1932-53) 08-03-2020, 08:52 AM
Replies: 18
Views: 1,023
Posted By G.M.
Re: PennGrade Motor Oil

When I was 16 I hung around a small engine rebuilding
shop. He had a stenzel made as a warning not to use any
Penna oil or there would be no guarantee. The Penna. oils
had a heavy gray muck that...
Forum: Early V8 (1932-53) 08-03-2020, 08:40 AM
Replies: 11
Views: 860
Posted By G.M.
Re: Engine issue

Valves sticking a little. Needs a dose of
Marvel Mystery Oil. G.M.
Forum: Early V8 (1932-53) 08-01-2020, 09:35 AM
Replies: 8
Views: 473
Posted By G.M.
Re: 1934 pickup horn : Who repairs these Sparton hornss

Any electric motor repair shop could check them
and rewire if required G.M.
Forum: Early V8 (1932-53) 07-28-2020, 04:01 PM
Replies: 33
Views: 1,454
Posted By G.M.
Re: Use of a MIG welder for other purposes?

You have to be careful shorting out the contact tip of
a MIG welder. When shorted the amps go way up. How
high depends on the out put range the machine is set
at. This can burn out the transformer...
Forum: Early V8 (1932-53) 07-28-2020, 03:52 PM
Replies: 12
Views: 426
Posted By G.M.
Forum: Early V8 (1932-53) 07-24-2020, 02:31 PM
Replies: 26
Views: 1,559
Posted By G.M.
Re: Gets warm and quits running?

Tom, I hate to tell you but condensers fail all the time
from heat. When Skip does a coil for some one he
asks them to send condensers so he can heat them
up to hot test them. They work cold but...
Forum: Early V8 (1932-53) 07-21-2020, 10:56 AM
Replies: 18
Views: 728
Posted By G.M.
Re: Shifting A Columbia In A '40

I made my own shifting controls. I don't like the way
the original ones work. I use 12 volt Pollock fuel shift valve
that is made for trucks with dual fuel tanks. As I described
I shifts by...
Forum: Early V8 (1932-53) 07-21-2020, 10:46 AM
Replies: 21
Views: 908
Posted By G.M.
Re: Water pump comparisons

Try a bottle of Purple Ice. This coats the inside surfaces
of the block and heads and transfers the heat into the
water. There is another product named Water Wetter. G.M.
Forum: Early V8 (1932-53) 07-21-2020, 10:38 AM
Replies: 26
Views: 1,559
Posted By G.M.
Re: Gets warm and quits running?

Do you really think you have a good one now?? If it
is a stock Ford coil new or old it will still fail on a hot
day in traffic when the engine gets hot. I have tested
hundreds of stock Ford coils...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 02:48 PM.