Forum: Early V8 (1932-53)
Yesterday, 09:02 AM
|
Replies: 15
Views: 631
|
Forum: Early V8 (1932-53)
04-20-2021, 06:54 PM
|
Replies: 7
Views: 321
Re: Hall Toledo Grinding Stones
What size & thread pitch are they. I have an Australian made Repco”Warren Brown “ seat refacing set but have not found an US made stones that fit.
Thanks
|
Forum: Early V8 (1932-53)
04-18-2021, 10:09 AM
|
Replies: 48
Views: 1,288
Re: Covid
Our thoughts and prayers you out to your family. Family first.
|
Forum: Early V8 (1932-53)
04-18-2021, 06:01 AM
|
Replies: 41
Views: 2,074
Re: crash
Very sorry to hear Brian. Has to be like losing a family member. Hopefully this bad situation will take a turn for the good. I certainly hope you are not hurt physically Brian.
|
Forum: Early V8 (1932-53)
04-16-2021, 11:48 AM
|
Replies: 21
Views: 794
Re: Cast iron surface rust removal
I too have used Muratic acid many times. It is very dangerous but great for certain components. I like it for gas tanks. It can also flash rust as soon as it dries. Rust 911 is safe & environmentally...
|
Forum: Early V8 (1932-53)
04-16-2021, 08:26 AM
|
Replies: 21
Views: 794
|
Forum: Early V8 (1932-53)
04-14-2021, 01:36 PM
|
Replies: 16
Views: 811
|
Forum: Early V8 (1932-53)
04-14-2021, 01:35 PM
|
Replies: 7
Views: 766
|
Forum: Early V8 (1932-53)
04-10-2021, 12:32 PM
|
Replies: 15
Views: 973
|
Forum: Early V8 (1932-53)
04-10-2021, 12:14 PM
|
Replies: 15
Views: 973
Re: Pines Winterfront 1936 Ford
Here’s all the pieces I have. There may be a few nuts & screws missing as packet was deteriorated bad. I have instructions & template for dash & will add later when I have them flattened.
|
Forum: Early V8 (1932-53)
04-08-2021, 03:57 PM
|
Replies: 62
Views: 2,532
|
Forum: Early V8 (1932-53)
04-08-2021, 09:57 AM
|
Replies: 15
Views: 973
Re: Pines Winterfront 1936 Ford
Great looking car Mercman. It has the Pines Trim. This is the box for the Pines Winterfront behind grille
https://www.jalopyjournal.com/forum/attachments/36winterfront-2-jpg.3386063/
And this is...
|
Forum: Early V8 (1932-53)
04-08-2021, 08:23 AM
|
Replies: 62
Views: 2,532
Re: How to repair damage to a deck
I know it’s not cracked but I would pin it with stitchlock pins where gasket needs to seal @ combustion chamber stitch away from chamber for apron. 1/4-3/8 in. Don’t over tighten pins cut of with ziz...
|
Forum: Early V8 (1932-53)
04-07-2021, 05:22 PM
|
Replies: 15
Views: 973
|
Forum: Early V8 (1932-53)
04-06-2021, 11:32 AM
|
Replies: 19
Views: 687
Re: Calculate actual quench height
Anthony be sure to check both side of engine. Do not assume they are alike. You have aluminum rods in your flathead? For what reason may I ask.
|
Forum: Early V8 (1932-53)
03-28-2021, 06:51 PM
|
Replies: 14
Views: 572
Re: Dual exhaust on right hand drive 1940 pickup
Oh dear. From the legendary home of Burt. So for sure you know Darrel the part time blues brother & Fraser. All great friends of mine. Not including John Smeeeeerth. 2 Forde rd.
I believe someone...
|
Forum: Early V8 (1932-53)
03-25-2021, 05:48 PM
|
Replies: 4
Views: 383
|
Forum: Early V8 (1932-53)
03-25-2021, 11:16 AM
|
Replies: 18
Views: 817
Re: welded crankshaft oil holes
Oops my bad. Yes Russ is correct. I guess I need new glasses or should use computer for pics not phone. Look correct as Russ stated
|
Forum: Early V8 (1932-53)
03-25-2021, 10:55 AM
|
Replies: 18
Views: 817
Re: welded crankshaft oil holes
Big mistake. Get another crank is my advice. You are not able clean it correctly now to include any welding splatter that may be in cavity & come loose a a later date destroying your fine engine. My...
|
Forum: Early V8 (1932-53)
03-24-2021, 05:57 AM
|
Replies: 8
Views: 622
|
Forum: Early V8 (1932-53)
03-23-2021, 05:54 PM
|
Replies: 7
Views: 516
|
Forum: Early V8 (1932-53)
03-23-2021, 04:49 PM
|
Replies: 24
Views: 1,658
|
Forum: Early V8 (1932-53)
03-22-2021, 11:18 AM
|
Replies: 7
Views: 444
|
Forum: Early V8 (1932-53)
03-21-2021, 06:18 PM
|
Replies: 12
Views: 487
|
Forum: Early V8 (1932-53)
03-20-2021, 05:01 AM
|
Replies: 26
Views: 1,551
|