Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 34
Search took 0.00 seconds.
Search: Posts Made By: bedfordboys24523
Forum: Model A (1928-31) 11-06-2017, 09:08 PM
Replies: 8
Views: 843
Posted By bedfordboys24523
Re: Can i run this Mallory 6v pos ground?

10-4 Tom, looking forward to firing this thing up soon.
Forum: Model A (1928-31) 11-05-2017, 09:47 PM
Replies: 8
Views: 843
Posted By bedfordboys24523
Re: Can i run this Mallory 6v pos ground?

Roger that, we'll give her a shot.
Forum: Model A (1928-31) 11-05-2017, 09:26 PM
Replies: 8
Views: 843
Posted By bedfordboys24523
Re: Can i run this Mallory 6v pos ground?

Its point type. The man I bought it from had never put it into in any thing and didn't know how it was set up.
I would think a modern dist like this would be set up for a 12volt neg ground system...
Forum: Model A (1928-31) 11-05-2017, 08:43 PM
Replies: 8
Views: 843
Posted By bedfordboys24523
Can i run this Mallory 6v pos ground?

Picked this Mallory up the other day and cant find any info on it as far as wiring it into a stock wiring harness. I don't plan on changing from a 6volt pos ground system. But I don't know how to...
Forum: Model A (1928-31) 10-14-2017, 08:44 AM
Replies: 10
Views: 1,341
Posted By bedfordboys24523
Re: Timing Marks?

I did when I purchased the cam. It's a ohv cam that he recommended with the 1.5 to 1 ratio Miller set up.
Forum: Model A (1928-31) 10-13-2017, 10:47 AM
Replies: 10
Views: 1,341
Posted By bedfordboys24523
Re: Timing Marks?

Roger that. I was under the impression for some reason the marks would be in alignment at TDC.
Thanks.
Forum: Model A (1928-31) 10-12-2017, 08:36 PM
Replies: 10
Views: 1,341
Posted By bedfordboys24523
Timing Marks?

Hello folks. Let me start by adding this is my first adventure in A land.
I am getting started on my miller ohv conversion and I have a 350 cam from Stipe I will be installing. My question is, is...
Forum: Early V8 12-06-2016, 09:39 PM
Replies: 0
Views: 517
Posted By bedfordboys24523
46-48 Hubs & Drums Wanted

Converting an A model to juice.
540-875-9991
Jesse
Forum: Early V8 (1932-53) 03-26-2013, 07:09 PM
Replies: 12
Views: 1,423
Posted By bedfordboys24523
Re: I need to talk to someone that has a dual carb intake on a 21 stud

I didnt do any welding with the gen intact it was disasembled. It took a good weld and seems pretty dang strong 3/8 steel with a 2 1/2x3 square washer. This was not my first choice but there is no...
Forum: Early V8 (1932-53) 03-25-2013, 07:27 PM
Replies: 12
Views: 1,423
Posted By bedfordboys24523
Re: I need to talk to someone that has a dual carb intake on a 21 stud

I have a copy of John Lawsons book with him building a flathead and doing 400+ dyno runs in the process and hp was gained with the risers.
I cut the mount off a old gen and made one with the right...
Forum: Early V8 (1932-53) 03-25-2013, 12:57 PM
Replies: 12
Views: 1,423
Posted By bedfordboys24523
I need to talk to someone that has a dual carb intake on a 21 stud

:mad:Thought I found a intake that I could use. 2 issues that I have are that the intake slot for the gen is 3/16 larger than the gen. The other is the fan pulley is a 1/2 more towards the rad than...
Forum: Early V8 (1932-53) 03-25-2013, 11:05 AM
Replies: 4
Views: 847
Posted By bedfordboys24523
21 stud edmunds intake/gen mounting concern

I put a dual carb intake on my 35 and went to install the gen and it sits in the grove on the intake very sloppy. Measured the gen base it is 2 1/2 inches and the intake slot is 2 11/16. Nothing is...
Forum: Early V8 (1932-53) 01-26-2013, 07:57 PM
Replies: 6
Views: 1,297
Posted By bedfordboys24523
Any one sell a longer fuel pump rod?

I have a edmunds dual carb intake I would like to run on my 21 stud. Does any one sell a longer rod? Can I mig weld an extension or should I braze it?
Forum: Early V8 (1932-53) 01-02-2013, 05:23 PM
Replies: 15
Views: 2,576
Posted By bedfordboys24523
Re: 21 stud oil pan question?

I pulled the intake and the vent tube is there, so I attempted to pull the pan but couldn't get it off, I had the front end out and trans un bolted and motor jacked up till it was hittting the fire...
Forum: Early V8 (1932-53) 01-02-2013, 11:45 AM
Replies: 15
Views: 2,576
Posted By bedfordboys24523
Re: 21 stud oil pan question?

Ok some of you have been helping me with an oil leak and this is what I found today. The baffle in the oil pan has a slit cut clean down to the bottom, why I have no idea. My question now is do I...
Forum: Early V8 (1932-53) 12-26-2012, 05:54 PM
Replies: 15
Views: 2,576
Posted By bedfordboys24523
Re: 21 stud oil pan question?

I'm almost positive that it has the correct oil pan gasket on it, the kit came with gaskets for two style pans and the ones I have left over aren't the right ones.
Forum: Early V8 (1932-53) 12-26-2012, 04:03 PM
Replies: 15
Views: 2,576
Posted By bedfordboys24523
Re: 21 stud oil pan question?

Walt,

The vent tube you talk about if it is not install the oil in the valley will fall stright down to the oil pan and leak out of the baffle? The motor I put in the truck was a fresh sleeve...
Forum: Early V8 (1932-53) 12-23-2012, 05:30 PM
Replies: 15
Views: 2,576
Posted By bedfordboys24523
21 stud oil pan question?

In the pass side front of the pan is what looks to me like a bafffle or maybe an overflow. The oil level on the stick is about an 1/8th inch above the full mark and there is oil leaking out of this...
Forum: Early V8 (1932-53) 05-02-2012, 09:44 PM
Replies: 15
Views: 2,246
Posted By bedfordboys24523
Re: Mac's Poor Customer Service????????

I will not be shopping there any more. In my last order I ordered two wheel studs and two head light stand bolts. They sent me two studs and two more studs in the bolt package, called them up and...
Forum: Early V8 (1932-53) 05-02-2012, 09:36 PM
Replies: 3
Views: 558
Posted By bedfordboys24523
What amp fuse to use 35 p/u

Wired my 35 and I can only run one headlight with out blowing a 30amp fuse. It will run both for about 20 sec. Thought it may have been in one of the headight harness (short) so I switched lights...
Forum: Early V8 04-21-2012, 04:52 PM
Replies: 1
Views: 499
Posted By bedfordboys24523
Is Loyd out there? (Crank Pulley)

I lost your number Loyd and was wondering if you still had the 35 crank pulley.
Forum: Early V8 04-12-2012, 05:14 PM
Replies: 1
Views: 542
Posted By bedfordboys24523
I need a 35 crank pulley

I am in need of a 35 crank pulley 540 875 9991 jesse
Forum: Early V8 (1932-53) 04-08-2012, 11:25 AM
Replies: 15
Views: 5,665
Posted By bedfordboys24523
Re: 6 volt or 12 volt generator ?

Ok im back with better news (I think). I disconnected the arm and batt wires that are on the cut out. Put a toggle switch and jumper wires to connect them, put volt meter on batt. Started truck and...
Forum: Early V8 (1932-53) 04-08-2012, 10:33 AM
Replies: 15
Views: 5,665
Posted By bedfordboys24523
Re: 6 volt or 12 volt generator ?

Thanks for the info I'm going out to the truck now to bypass the cutout and adjust the 3rd brush. Ill be back.
Forum: Early V8 (1932-53) 04-07-2012, 09:25 PM
Replies: 15
Views: 5,665
Posted By bedfordboys24523
Re: 6 volt or 12 volt generator ?

Its a 35 3 brush, Ive got the cover off the cutout I am using the plastic spacers on the screws so I know they are not touching any of the guts of the cutout. Is there a way of telling a 6v from a...
Showing results 1 to 25 of 34

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:44 AM.