Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 16 of 16
Search took 0.00 seconds.
Search: Posts Made By: CHerdic
Forum: Model A (1928-31) 02-12-2017, 05:04 PM
Replies: 5
Views: 1,659
Posted By CHerdic
Re: 1930 side mount spare tire mount

Trying to reattach spare side mount on 28 tudor. New splash shield have installed; no
previous holes to go by. Need help and/or pictures.
Forum: Model A (1928-31) 09-24-2016, 05:40 AM
Replies: 2
Views: 493
Posted By CHerdic
Interior wood kit

28 tudor is about to be given a final painting. Interior work to follow. Is it best to install the new interior wood kit before the paint job or after.
Forum: Model A (1928-31) 08-11-2013, 10:37 AM
Replies: 10
Views: 2,388
Posted By CHerdic
charging 6 volt batteries in series

Recent reviews of recommendations for charging a 6 volt battery with a 12 volt charger emphasize connecting the 6 volt batteries(2) in series then using a 12 volt charger to charge both. Must both...
Forum: Model A (1928-31) 07-03-2013, 06:53 PM
Replies: 6
Views: 1,212
Posted By CHerdic
Re: Startup of 28 tudor - HELP!

Problem appears to have been caused by wires from a new wiring harness, not yet attached to headlights shorting out on the floor. All were caped off , problem gone.

The start up process...
Forum: Model A (1928-31) 07-03-2013, 10:27 AM
Replies: 6
Views: 1,212
Posted By CHerdic
Startup of 28 tudor - HELP!

After 15 years of rebuilding, car is scheduled for a start up. When I made the final hookup of a new battery, to all new wiring, a big spark resulted.

Is equiped with a shutoff switch next to...
Forum: Model A (1928-31) 06-19-2013, 07:19 AM
Replies: 6
Views: 2,210
Posted By CHerdic
Question Re: Model A - Light Switch Rod

Having the exact same problem with my 28 tudor. Pulled the new rod, tightend steering wheel nut, reinstalled; light switch turns with the steering wheel.
Forum: Model A (1928-31) 06-12-2013, 07:47 AM
Replies: 2
Views: 629
Posted By CHerdic
light and horn rod

Need help on installing new horn and light rod. Lower end is too tight to fit into top of steering column. What is best to lubricate thw new rod?
Forum: Model A (1928-31) 04-13-2013, 03:41 PM
Replies: 3
Views: 1,069
Posted By CHerdic
Question Throttle control linkage month

Just reviewed the most recent post and saw what may be my next concern. Right now I'm trying to figure out how to reattach a the throttle control assembly that was taken off 14 years ago. Any help...
Forum: Model A (1928-31) 04-07-2013, 04:24 PM
Replies: 2
Views: 748
Posted By CHerdic
Oil in steering column holes

Near the top of a 28 steering column are two holes, right and left, which appear to be an opportunity to oil both levers onthe column.
Assuming this is accurate, what type/ weight oil is best?
Forum: Model A (1928-31) 03-31-2013, 10:15 AM
Replies: 2
Views: 902
Posted By CHerdic
pressue washing gas tank

Gas tank inspection shows a a samll amount of corrosion. Has been day for at least 40 years. Have had a recommendation to wash the tank with hot soap and water, dry and followed by rinsing with...
Forum: Model A (1928-31) 03-26-2013, 06:42 AM
Replies: 10
Views: 2,044
Posted By CHerdic
Re: Sanding the horn commutator

Acetone on the teeth might work, but it may be rough on gum tissue.
Forum: Model A (1928-31) 03-19-2013, 12:42 PM
Replies: 8
Views: 1,946
Posted By CHerdic
Rebuilt water pump impeller

I am attempting to install a rebuilt water pump on to the motor of a 28 tudor.
The impeller blades are rubbing on inside of the motor. Had the bearings and packing nut professionally installed...
Forum: Model A (1928-31) 02-15-2013, 10:59 AM
Replies: 11
Views: 1,647
Posted By CHerdic
Re: Help with windshield installation

Had a similar experience with my 28-tudor. Two flat head screws in upper corners. Had to drillout rusted screws, clean up and retap for reattachment.
Forum: Model A (1928-31) 02-11-2013, 08:41 PM
Replies: 4
Views: 780
Posted By CHerdic
Re: Outer cover for universal joint

GOT IT! It fits. Now ,it's on to the next of many other "mini" projects.
Forum: Model A (1928-31) 02-11-2013, 08:09 AM
Replies: 4
Views: 780
Posted By CHerdic
Re: Outer cover for universal joint

The front motor mount (not original style) is being replaced. This will lower the U joint .
However I still have slight misalignment with the top cover "arm" and the frame cross member. Does this...
Forum: Model A (1928-31) 02-05-2013, 10:54 AM
Replies: 4
Views: 780
Posted By CHerdic
Outer cover for universal joint

Having trouble replacing the upper half of outer cover on 28 tudor universal joint. Guard on top hits the cross frame member. Any ideas?
Showing results 1 to 16 of 16

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 10:03 AM.