Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 15 of 15
Search took 0.01 seconds.
Search: Posts Made By: jimtims
Forum: Early V8 (1932-53) 09-15-2021, 06:16 PM
Replies: 15
Views: 575
Posted By jimtims
Re: ford 47 pickup starter alignment problem

Thank you for the tip on the small bracket. My truck did not have the bracket when I got it 6 years ago. I have gone thru 3 starters in the time I have had the truck and I put a new starter in today...
Forum: Early V8 (1932-53) 09-09-2021, 09:47 AM
Replies: 15
Views: 575
Posted By jimtims
Re: ford 47 pickup starter alignment problem

I have pictures and will try to post them,
Jim
Forum: Early V8 (1932-53) 09-09-2021, 09:45 AM
Replies: 15
Views: 575
Posted By jimtims
Re: ford 47 pickup starter alignment problem

i have one on order. hoping it will cure my alignment issues.
Jim
Forum: Early V8 (1932-53) 09-09-2021, 09:43 AM
Replies: 15
Views: 575
Posted By jimtims
Re: ford 47 pickup starter alignment problem

Thank you all for your replies. when I figure out how to post a picture on this site, I will.
Jim
Forum: Early V8 (1932-53) 09-07-2021, 01:28 PM
Replies: 15
Views: 575
Posted By jimtims
Re: ford 47 pickup starter alignment problem

i think I have an after market housing for my starter , it is not cast but about 16 gauge metal that has been spot welded onto the oil pan. I assume misalignment caused the gear on the starter shaft...
Forum: Early V8 (1932-53) 09-07-2021, 11:24 AM
Replies: 15
Views: 575
Posted By jimtims
Re: ford 47 pickup starter alignment problem

i am not familiar with the bracket you reference. it is an 11 inch flywheel.
jim
Forum: Early V8 (1932-53) 09-07-2021, 10:52 AM
Replies: 15
Views: 575
Posted By jimtims
ford 47 pickup starter alignment problem

how to adjust alignment with shims 59 AB ENGINE.
JIM
Forum: Questions & Suggestions 07-22-2021, 05:35 PM
Replies: 1
Views: 258
Posted By jimtims
47 ford p/u

how to replace gear ring on flywheel
Forum: Early V8 (1932-53) 07-22-2021, 05:21 PM
Replies: 6
Views: 393
Posted By jimtims
Re: replace ring on flywheel 47 ford pickup

not sure how to use this site
Forum: Early V8 (1932-53) 07-22-2021, 05:17 PM
Replies: 6
Views: 393
Posted By jimtims
replace ring on flywheel 47 ford pickup

i need to replace the ring on my fly wheel and want to recondition the the clutch at the same time.i have a 1947 ford stake bed with 4 speed Transmission.
Forum: Questions & Suggestions 08-15-2014, 10:24 AM
Replies: 1
Views: 871
Posted By jimtims
jim's 47 ford pickup emergency brake

Any tips on adjusting cables to make emergency brake hold?
Forum: Questions & Suggestions 08-01-2014, 09:55 PM
Replies: 1
Views: 885
Posted By jimtims
fuel regulator

I have a 47 ford pickup with a flathead V8. I installed a carter electric fuel pump. Do I need a fuel regulator to reduce the pressure from 6 psi. It seems to run fine with no regulator. I live at...
Forum: Early V8 (1932-53) 07-23-2014, 10:31 PM
Replies: 5
Views: 749
Posted By jimtims
Re: 47 ford pickup

Jonnyj, thanks, I had to elongate the slot a bit but it works fine now. Jim
Forum: Early V8 (1932-53) 07-23-2014, 08:12 PM
Replies: 5
Views: 749
Posted By jimtims
Re: 47 ford pickup

Thanks,but I have loosened the bolts and it doesen't move
Forum: Early V8 (1932-53) 07-23-2014, 04:53 PM
Replies: 5
Views: 749
Posted By jimtims
47 ford pickup

I am having trouble closing the hood latch on my pickup. Jim
Showing results 1 to 15 of 15

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 02:46 AM.