Forum: Late V8
01-21-2020, 05:23 PM
|
Replies: 1
Views: 1,305
|
Forum: Late V8
12-15-2019, 12:11 PM
|
Replies: 1
Views: 1,305
1947 Mercury Convertible sell or trade
1947 Mercury Convertible, new 8BA flathead engine, rebuilt 3 speed transmission and clutch, Powermaster alternator with 12 volt system, floors redone to original specs, new reproduction trunk floor,...
|
Forum: Early V8 (1932-53)
08-12-2019, 09:05 AM
|
Replies: 52
Views: 7,961
Re: Bat piss
Bats can be a benefit as they can eat thousands of mosquitos every night. We use them here in the SE as we would not be able to stand outside for any period of time at night without being chewed...
|
Forum: Late V8
06-12-2019, 01:27 PM
|
Replies: 1
Views: 1,148
|
Forum: Late V8
06-12-2019, 08:38 AM
|
Replies: 1
Views: 1,148
1947 Mercury Convertible DRIVER FLATHEAD
What we have here is a 1947 Mercury convertible that I bought here on the HAMB back 2 years ago. I was an old custom that had shaved door handles and an early hemi. The floors and trunk were pretty...
|
Forum: Early V8
01-26-2019, 07:43 AM
|
Replies: 1
Views: 981
|
Forum: Early V8
01-16-2019, 09:10 AM
|
Replies: 1
Views: 981
|
Forum: Early V8
01-16-2019, 09:02 AM
|
Replies: 1
Views: 1,049
|
Forum: Early V8
01-15-2019, 05:03 PM
|
Replies: 1
Views: 1,049
Ford Top Loader 3 Speed transmission
Ford top loader 3 speed transmission, Series 48-7006 from 1935-1936 passenger car. Turns freely and will accept the 11 inch clutch. Gears a good a greasy. $275 + shipping from 28027. Have a full set...
|
Forum: Early V8
12-28-2018, 07:20 PM
|
Replies: 5
Views: 1,534
|
Forum: Early V8
12-28-2018, 07:20 PM
|
Replies: 1
Views: 1,251
|
Forum: Late V8
12-15-2018, 11:00 AM
|
Replies: 0
Views: 1,179
Wanted: 1956 FORD F100 Pickup PROJECT
Looking for a '56 F100 half ton pickup "project" truck. Original with no motor or transmission preferred. but will consider any unfinished hot rod project. Some rust okay. Need to have a title with...
|
Forum: Early V8
12-15-2018, 10:58 AM
|
Replies: 0
Views: 826
Wanted: 1956 FORD F100 Pickup PROJECT
Looking for a '56 F100 half ton pickup "project" truck. Original with no motor or transmission preferred. but will consider any unfinished hot rod project. Some rust okay. Need to have a title with...
|
Forum: Early V8
12-11-2018, 06:45 PM
|
Replies: 1
Views: 1,251
1946-48 Mercury Car Steering Column WANTED
Looking for a Mercury steering column from a 1946-1948 passenger car. I need the steering box, mast, and shifter mechanism with linkage. Steering wheel is not necessary, but need good threads on...
|
Forum: Early V8
11-08-2018, 06:50 PM
|
Replies: 5
Views: 1,534
|
Forum: Early V8
09-15-2018, 01:40 PM
|
Replies: 5
Views: 1,534
|
Forum: Early V8
08-03-2018, 07:35 AM
|
Replies: 5
Views: 1,534
|
Forum: Early V8 (1932-53)
06-22-2018, 07:56 AM
|
Replies: 23
Views: 5,828
|
Forum: Early V8 (1932-53)
06-22-2018, 07:52 AM
|
Replies: 23
Views: 5,828
|
Forum: Early V8 (1932-53)
06-22-2018, 07:47 AM
|
Replies: 23
Views: 5,828
|
Forum: Early V8
06-20-2018, 06:06 PM
|
Replies: 5
Views: 1,534
Re: 1946 Mercury/Ford Sheet Metal
Here is what Mercury/Ford parts I have:
3 rear fenders (2 left 1 right)
2 sets of front fenders (left & right)
1 set of inner fenders (left & right)
1 floor board (removable part)
1 set...
|
Forum: Early V8
06-19-2018, 06:30 AM
|
Replies: 5
Views: 1,534
1946 Mercury/Ford Sheet Metal
Hello All,
I have a collection of 1946-1948 Mercury fenders, doors and hood. These are parts left over from a 1946 Mercury convertible that I am working on. I also have window regulators and...
|
Forum: Early V8
07-18-2017, 07:20 PM
|
Replies: 0
Views: 718
WTB 16x5 steel wheels
Looking for a pair of 16x5 Ford/Lincoln wheels 1940 vintage. Must have hubcap nubs towards the inside of the wheel. Call or email me. 704-918-6272. Or [email protected]. Thanks. Curt
|
Forum: Late V8
05-06-2017, 09:07 PM
|
Replies: 0
Views: 949
Looking for windshield panel 1934 ford
Looking the panel that goes above the windshield on the inside of a 1933 or 1934 ford. The one I have is rusted out pretty bad, so it would be great to find something that I can work with.
|
Forum: Late V8
04-17-2017, 12:40 PM
|
Replies: 1
Views: 1,258
|