Forum: Early V8 (1932-53)
09-11-2022, 01:42 PM
|
Replies: 80
Views: 144,249
Re: Manners... A new rule...
Hi Ryan. This is unrelated to the post above. I m a several year member in the early v8 forum. Lgndlt5. I purchased. Model A a year ago. I had reached out to enjoy access privileges to the model A...
|
Forum: Early V8 (1932-53)
02-09-2022, 07:59 PM
|
Replies: 80
Views: 144,249
Re: Manners... A new rule...
Hi Ryan so sorry to hijac this ancient thread. Am sort of. frustrated. Essentially I reached out several months ago requesting full access FYI the Model A forum so I can utilize it fully. Never got a...
|
Forum: Early V8 (1932-53)
01-14-2022, 11:37 PM
|
Replies: 3
Views: 648
Re: Banjo Bolt
Ahh!! I have searched for months also. None I have found will fit the OD diameter of the bolt. 5/16 “ a if memory serves. I bought a brass brake fitting from an early Porsche 911 with an ID that has...
|
Forum: Early V8 (1932-53)
10-01-2021, 07:39 PM
|
Replies: 19
Views: 1,832
|
Forum: Early V8 (1932-53)
10-01-2021, 06:04 PM
|
Replies: 40
Views: 8,093
|
Forum: Early V8 (1932-53)
10-01-2021, 03:31 PM
|
Replies: 19
Views: 1,832
|
Forum: Early V8
09-30-2021, 03:04 PM
|
Replies: 2
Views: 567
|
Forum: Early V8
09-29-2021, 08:03 PM
|
Replies: 2
Views: 567
|
Forum: Early V8
09-25-2021, 09:51 AM
|
Replies: 2
Views: 567
|
Forum: Early V8 (1932-53)
09-22-2021, 08:41 PM
|
Replies: 22
Views: 2,076
Re: Need advice on a 1936 Ford
Oh my heavens. Hi Don I was searching in an the forum today in an attempt to “engineer” remote oil filter system for my 36 sedan. Searched and found this thread. You posted pictures of the exact...
|
Forum: Early V8 (1932-53)
09-22-2021, 06:58 PM
|
Replies: 10
Views: 2,114
Re: Oil filter add to 36 lb?
Sorry mistyped I am not going to remove the oil pan to plumb a drain line. Can’t do that heavy work anymore. I hate spellcheck and old fat fingers.
|
Forum: Early V8 (1932-53)
09-22-2021, 06:52 PM
|
Replies: 10
Views: 2,114
Re: Oil filter add to 36 lb?
Thank you both or our responses. I remain a bit confused however. How wou rerun oil o he lifter valley cause increased oil consumption? Would it not be ok to route the restricted oil flow down...
|
Forum: Early V8 (1932-53)
09-21-2021, 09:04 PM
|
Replies: 10
Views: 2,114
Oil filter add to 36 lb?
Would it be possible to add an oil filter return line by tapping into one of the oil pressure sender port(s) on the back of an lb block and more importantly could I run the return line to the fuel...
|
Forum: Early V8 (1932-53)
09-14-2021, 05:18 PM
|
Replies: 26
Views: 2,383
Re: '35 Ford Coupe tail light lamp
The bulb base and socket only goes together one direction please note the staggered height of the pins on the bulb base. Olso in the socket. Push down when those are aligned and turn bulb 1/4 turn to...
|
Forum: Early V8 (1932-53)
09-05-2021, 04:58 PM
|
Replies: 6
Views: 873
Re: 39 Shifter Question
Hi Charlie. Could you call
Me at your convenience. Fuel pump great my ignition failed. Help? Also I still done have your mail correct thanks john sullivan 847-275-4841 thanks
|
Forum: Early V8 (1932-53)
09-05-2021, 11:00 AM
|
Replies: 14
Views: 3,052
Re: Help identify these distributors and coil
Greetings Bubba. I hope you are doing well. I need a replacement distributor for a 36 221 stock. I am hoping that you may have one available rebuilt for exchange. Car sat since fall 2019 in cold...
|
Forum: Early V8 (1932-53)
07-31-2021, 05:21 PM
|
Replies: 5
Views: 2,261
Re: 1940 Coupe side quarter glass installation
Hi Tom. Just a thought. I recently purchased a back glass seal 36 sedan from C&G it is a black “U” channel with 3 square sides it might do the trick if you are looking for filler. $14.95. It seems...
|
Forum: Early V8 (1932-53)
07-30-2021, 01:00 PM
|
Replies: 22
Views: 3,663
Re: Diamond Back Bias Ply looking radials
Hi my experience with 4 auburns recently purchased and shipped were priced similar to those mentioned by “bored and stroked” above. How did you end up with over $2,000 almost double what I was...
|
Forum: Early V8 (1932-53)
07-29-2021, 03:13 PM
|
Replies: 22
Views: 3,663
Re: Diamond Back Bias Ply looking radials
Adding due to typos do not over inflate bike tube too much just enough to seal the gap valve core out of tire keep it very slippery with tire mounting lube it will pop out mostly as beads seat grab...
|
Forum: Early V8 (1932-53)
07-29-2021, 03:01 PM
|
Replies: 3
Views: 659
|
Forum: Early V8 (1932-53)
07-29-2021, 12:12 PM
|
Replies: 26
Views: 6,789
|
Forum: Early V8 (1932-53)
07-29-2021, 12:12 PM
|
Replies: 26
Views: 6,789
|
Forum: Early V8 (1932-53)
07-29-2021, 12:11 PM
|
Replies: 26
Views: 6,789
|
Forum: Early V8 (1932-53)
07-29-2021, 12:10 PM
|
Replies: 26
Views: 6,789
|
Forum: Early V8 (1932-53)
07-29-2021, 12:09 PM
|
Replies: 26
Views: 6,789
|