Forum: Early V8 (1932-53)
11-27-2020, 04:57 AM
|
|
Replies: 1
Views: 215
|
|
Forum: Early V8 (1932-53)
11-24-2020, 04:35 AM
|
|
Replies: 2
Views: 323
59a oil pump capacity.
I have pulled apart a 59a engine to control everything and replace a few parts.
Story on the engine is that it was NOS up until 1989, put into a 1939 pu and driven very little for about 10 years...
|
|
Forum: Model A (1928-31)
06-30-2020, 12:42 PM
|
|
Replies: 3
Views: 531
|
|
Forum: Model A (1928-31)
06-30-2020, 10:28 AM
|
|
Replies: 3
Views: 531
G28T center cam bearing oiling?
I now have my rebuilt G28T block and bottom end on the bench, and as always i go through the oil passage system.
These are as some of you know full pressure B type block, they have a solid top oil...
|
|
Forum: Early V8 (1932-53)
01-24-2020, 03:50 AM
|
|
Replies: 22
Views: 1,736
Re: How do I get pressure plate out.
Use the 3/8" ratchet set and there is a small radius on the top of the opening in the block allowing the ratchet extender to reach the bolts pretty straight on. Then you should be able to "walk" the...
|
|
Forum: Early V8 (1932-53)
01-30-2019, 04:09 AM
|
|
Replies: 50
Views: 6,570
Re: Want o go highway speeds ??? Need opinions.
I had a 48 running hot all the time, rebuilt and advanced the ign 2 degrees, still hot,
then i ran 50/50 white vinegar and water for one day around the backroads, in the afternoon bottom tap was...
|
|
Forum: Early V8 (1932-53)
10-10-2018, 03:53 AM
|
|
Replies: 2
Views: 581
1942-48 distributor parts.
Hi, i need to find a source for 1942-48 distributor tiny wire connector rubber boot and slotted nut, either nos or new. is this available anywhere? thanks.
|
|
Forum: Early V8
10-10-2018, 03:19 AM
|
|
Replies: 2
Views: 892
|
|
Forum: Early V8 (1932-53)
08-30-2018, 03:13 AM
|
|
Replies: 8
Views: 1,449
|
|
Forum: Early V8 (1932-53)
08-29-2018, 07:23 AM
|
|
Replies: 8
Views: 1,449
V8 lockable gas cap.
Who made this very cool V8 locking gas cap? The key and cylinder is Star brand.
I suppose it is an aftermarket item? i have not seen this type before.
|
|
Forum: Early V8 (1932-53)
08-28-2018, 05:19 AM
|
|
Replies: 9
Views: 1,546
|
|
Forum: Early V8
08-28-2018, 04:20 AM
|
|
Replies: 0
Views: 484
|
|
Forum: Early V8 (1932-53)
08-27-2018, 02:36 AM
|
|
Replies: 16
Views: 4,542
Re: Stromberg eFire Dizzy
I agree, i rebuild, test and run the 1942-48 "crab" distributor, for people and myself.
It`s hard to see any gains in this new unit, why replace the best distributor ever made for a modern unit...
|
|
Forum: Early V8 (1932-53)
08-12-2018, 01:37 PM
|
|
Replies: 4
Views: 850
|
|
Forum: Early V8 (1932-53)
08-12-2018, 12:53 PM
|
|
Replies: 4
Views: 850
|
|
Forum: Early V8
02-27-2018, 09:09 AM
|
|
Replies: 1
Views: 551
|
|
Forum: Early V8 (1932-53)
02-09-2018, 04:42 AM
|
|
Replies: 61
Views: 9,046
Re: Coil deal!!
Tried to buy four but unfortunately they will not ship outside US.
|
|
Forum: Early V8
01-15-2018, 04:57 AM
|
|
Replies: 0
Views: 575
2" Winfield D Downdraft and 2" Riley sidedraft.
Looking for a number two of these two carburetors.
2" Winfield D Downdraft and 2" Riley sidedraft.
Any leads are appreciated.
I have other interesting carburetors and ignition systems for trade...
|
|
Forum: Model-A
01-15-2018, 04:54 AM
|
|
Replies: 0
Views: 506
2" Winfield D Downdraft and 2" Riley sidedraft
Looking for a number two of these two carburetors.
2" Winfield D Downdraft and 2" Riley sidedraft.
Any leads are appreciated.
I have other interesting carburetors and ignition systems for trade...
|
|
Forum: Early V8 (1932-53)
10-31-2017, 03:46 AM
|
|
Replies: 88
Views: 9,130
Re: Condenser Capacitiance.
This is our test equipment. 1940s VLC (european KRW) from a local Ford shop still works wonderfully, Serial resistance, leakage and capitance. 220 volts.
The other tester is for coils.
|
|
Forum: Early V8 (1932-53)
10-20-2017, 07:15 AM
|
|
Replies: 14
Views: 1,906
|
|
Forum: Early V8 (1932-53)
09-28-2017, 03:57 AM
|
|
Replies: 1
Views: 433
1937-48 truck water pumps disassembly.
How to i disassemble 1937-48 truck water pumps?
I`m used to the regular water pumps with bronze bushing, and they come apart real easy in a press.
Hard to tell if the bearing is locked into the...
|
|
Forum: Early V8
09-12-2017, 05:30 AM
|
|
Replies: 2
Views: 892
|
|
Forum: Model A (1928-31)
09-10-2017, 02:09 PM
|
|
Replies: 3
Views: 855
|
