Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 393
Search took 0.01 seconds.
Search: Posts Made By: daren007
Forum: Model A (1928-31) 06-07-2019, 05:35 PM
Replies: 10
Views: 493
Posted By daren007
Re: Heater hose connection

Scatt. The amount needed is too small for aircraft use. Check your local aircraft maintenance facility. They usually throw out pieces this short.
Forum: Model A (1928-31) 06-02-2019, 07:33 AM
Replies: 27
Views: 2,731
Posted By daren007
Re: Nu-rex Timing wrench

Nu-Rex and fords method are about the same accurate. If you use either then check with a timing light you will be disappointed. Splitting hairs is not necessary. Fords method worked for millions of...
Forum: Model A (1928-31) 05-27-2019, 08:02 AM
Replies: 13
Views: 1,108
Posted By daren007
Re: How to get that perfect exhaust sound?

My wife doesn't think much of my exhaust sound.
Forum: Model A (1928-31) 05-26-2019, 10:24 PM
Replies: 6
Views: 383
Posted By daren007
Re: Engine Idle

The model "B" uses 19 degrees BTDC initial timing, Wouldn't this give a rough idle opposed to TDC for the "A". Somehow this does not make sense. The "A" owners manual says to advance 1/2 after...
Forum: Model A (1928-31) 05-26-2019, 04:23 PM
Replies: 6
Views: 383
Posted By daren007
Re: Engine Idle

My "T" idles so nice even with spark advance.
Forum: Model A (1928-31) 05-26-2019, 01:17 PM
Replies: 6
Views: 383
Posted By daren007
Engine Idle

I have both "A" and "B" engines that have been rebuilt. The "A" did not have the lifter bores reamed to oversized lifters nor the cam bore wear repaired. The "B" lifter bores were not repaired and...
Forum: Model A (1928-31) 05-25-2019, 08:36 AM
Replies: 10
Views: 471
Posted By daren007
Re: compressor water and moisture extractor

Use black pipe not copper or plastic to condense the moisture and mount your separator as far down stream as possible.
Forum: Model A (1928-31) 05-19-2019, 07:08 PM
Replies: 27
Views: 2,045
Posted By daren007
Re: Exh. manifold to muffler; does anyone make....

Skip muffler shops. Find a exhaust fabricator shop. Our local shop made me one for my run up stand for $8.00.
Forum: Model A (1928-31) 05-11-2019, 07:34 PM
Replies: 0
Views: 194
Posted By daren007
Tillotson X

I have a Tillotson X I do not know it's history. The carb is clean as well as the passages. The manifold flange is flat and so is the bowl lower body. The upper body has a slight warp however I...
Forum: Model A (1928-31) 05-08-2019, 07:32 AM
Replies: 3
Views: 233
Posted By daren007
Cylinder leak down test

What should I use for my base psi and what should I expect for differential on a "A" and "B" engine. I expect the "A" and "B" to be the same.


Thanks.
Forum: Model A (1928-31) 05-06-2019, 06:05 PM
Replies: 10
Views: 507
Posted By daren007
Re: Kink pins

Some interesting and good advise here. Thanks.
Forum: Model A (1928-31) 05-05-2019, 08:13 PM
Replies: 10
Views: 507
Posted By daren007
Re: Kink pins

Blame......Sheesh
Forum: Model A (1928-31) 05-05-2019, 08:12 PM
Replies: 10
Views: 507
Posted By daren007
Re: Kink pins

King pins.....did I do this or can I Blair it on spell check.
Forum: Model A (1928-31) 05-05-2019, 08:11 PM
Replies: 10
Views: 507
Posted By daren007
Kink pins

I have a friend that after installing new king pins the brake actuator housings do not fit properly. The housings have are approximately 3/16 from completely entering the pins. I donít think the...
Forum: Model A (1928-31) 05-04-2019, 07:20 AM
Replies: 42
Views: 1,874
Posted By daren007
Re: how much assembly did Assembly Plants do?

This brings up another question on paint although somewhat off topic. How do todays plants paint different colors for each line. do the bodies split up for each color then re enter the line or do...
Forum: Model T (1909-1927) 04-30-2019, 09:58 PM
Replies: 3
Views: 378
Posted By daren007
Re: new to the forum

3/4 cam? I have heard this so many times over the years but no one could tell me what a 3/4 cam is.
Forum: Model A (1928-31) 04-27-2019, 08:37 PM
Replies: 17
Views: 1,001
Posted By daren007
Re: Nurex Timing Gage

It will get you close. Not really better then Fords method but easier.
Forum: Model A (1928-31) 04-22-2019, 10:12 PM
Replies: 16
Views: 832
Posted By daren007
Re: what does "insurance" on shipping actually cover?

Ordered a pair of door sill trim pieces from MOPAR. When picking them up I noticed something did not look right with one of the boxes. I opened it in front of the parts man only to find somewhere...
Forum: Model A (1928-31) 04-21-2019, 07:05 PM
Replies: 16
Views: 832
Posted By daren007
Re: what does "insurance" on shipping actually cover?

I had a trim piece shipped to me. The shipper used a USPS triangular box. The package arrived with the box bent in the middle. The trim piece was damaged beyond repair. When I asked the Post...
Forum: Model T (1909-1927) 04-21-2019, 08:20 AM
Replies: 4
Views: 757
Posted By daren007
Forum: Model A (1928-31) 04-13-2019, 08:16 PM
Replies: 32
Views: 2,100
Posted By daren007
Re: Brake adjustment - Frustration

If you have worn parts you are chasing your tail. Throw the board away and make it work.
Forum: Model A (1928-31) 04-13-2019, 11:37 AM
Replies: 19
Views: 1,037
Posted By daren007
Re: Main bearing bolts

That's what I thought although I don't have that problem.
Forum: Model A (1928-31) 04-13-2019, 07:59 AM
Replies: 19
Views: 1,037
Posted By daren007
Re: Main bearing bolts

You can buy "Stat-o-seal" washers from aircraft hardware suppliers or your local Aircraft maintenance facility may have them.
Forum: Model A (1928-31) 04-13-2019, 07:55 AM
Replies: 19
Views: 1,037
Posted By daren007
Re: Main bearing bolts

Can someone tell me the theory behind "Pressure sealing washers".
Forum: Model A (1928-31) 04-12-2019, 09:40 PM
Replies: 33
Views: 1,534
Posted By daren007
Re: Help she no go....

Stop using starter fluid.
Showing results 1 to 25 of 393

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 10:54 AM.