Forum: Model A (1928-31)
04-12-2024, 09:13 PM
|
Replies: 8
Views: 585
|
Forum: Model A (1928-31)
03-26-2024, 08:28 PM
|
Replies: 8
Views: 551
Re: 7 tooth retainer clip
I measured 17mm ID. But found only 18mm or 16mm ID. I ordered both. 16mm was too small. 18mm looks good.
|
Forum: Model A (1928-31)
03-25-2024, 01:29 PM
|
Replies: 8
Views: 551
Re: 7 tooth retainer clip
I measured and ordered from McMaster. Looks like the order might arrive next day. I will return here and provide the details if the rings fit. Thanks for the advice.
|
Forum: Model A (1928-31)
03-24-2024, 10:24 PM
|
Replies: 8
Views: 551
Re: 7 tooth retainer clip
I look like I have a broken one of these https://www.kaiserwillys.com/products/nos-steering-worm-gear-bearing-retainer-ring-2-required-fits-41-66-mb-gpw-cj-2a-3a-3b-5-m38-m38a1/
Is there a generic...
|
Forum: Model A (1928-31)
03-24-2024, 08:19 PM
|
Replies: 8
Views: 551
7 tooth retainer clip
I have a lot of slop in my steering. And I just came across a new steering wheel. So I am currently taking apart my 7 tooth box to make sure everything is as good as I can possibly make it, before I...
|
Forum: Model A (1928-31)
02-05-2024, 09:48 AM
|
Replies: 28
Views: 1,230
Re: Loss of power,
I could not decide on original points, or modern. I read plenty of posts about original points working as expected. And no need for modern unless the condenser keeps burning up. I may buy a set of...
|
Forum: Model A (1928-31)
02-04-2024, 09:05 PM
|
Replies: 28
Views: 1,230
Re: Loss of power,
I spent the evening going through the engine. A multi point inspection if you will. I found that there are a couple of scratches in the distributor cam that wore down the pad on the breaker arm and...
|
Forum: Model A (1928-31)
02-04-2024, 09:48 AM
|
Replies: 28
Views: 1,230
Re: Loss of power,
I swapped out the carb yesterday already when I started my drive. I brought a known good carb with me.
The engine would maintain a fast idle, even with the spark retarded. I could not get the...
|
Forum: Model A (1928-31)
02-03-2024, 11:23 PM
|
Replies: 28
Views: 1,230
Re: Loss of power,
I bent the wire connector 90 degrees when attaching it to the upper plate.
I'll do the box gap cleaning tip tomorrow.
Dizzy is in reference to the distributor rotor, correct?
|
Forum: Model A (1928-31)
02-03-2024, 09:07 PM
|
Replies: 28
Views: 1,230
|
Forum: Model A (1928-31)
02-03-2024, 08:37 PM
|
Replies: 28
Views: 1,230
Re: Loss of power,
Champion plugs. I pulled #1 plug on the side of the road. It was light Grey color. No moisture.
I'll pull the others when I get home
|
Forum: Model A (1928-31)
02-03-2024, 08:03 PM
|
Replies: 28
Views: 1,230
Loss of power,
Okay fellas, I'm stumped. I started to drive my 28 coupe long distances. Today I drove from Santa Clarita to Camarillo. About 60 miles. I made it to my destination without any problems. Then on the...
|
Forum: Model A (1928-31)
01-03-2024, 06:35 PM
|
Replies: 24
Views: 3,518
|
Forum: Model A (1928-31)
09-24-2023, 03:09 PM
|
Replies: 10
Views: 1,625
|
Forum: Model A (1928-31)
09-05-2023, 11:27 AM
|
Replies: 10
Views: 776
|
Forum: Model A (1928-31)
09-05-2023, 08:55 AM
|
Replies: 10
Views: 776
Re: Radiator, no overflow tube
Exactly nkaminar. The backside of the radiator has an overhang where I was considering adding the tube. Running it down the drivers side. I'll also replace the gasket on the cap.
|
Forum: Model A (1928-31)
09-04-2023, 11:21 PM
|
Replies: 10
Views: 776
|
Forum: Model A (1928-31)
09-04-2023, 10:26 PM
|
Replies: 10
Views: 776
Radiator, no overflow tube
I've been working on my vehicle over the last few months. Fixing things here and there. The engine runs a little better after each repair. And with each repair, I drive the car a little more. And...
|
Forum: Model A (1928-31)
08-08-2023, 04:54 PM
|
Replies: 47
Views: 4,159
Re: black wall tires
I just purchased from Lucas a few weeks ago. And I am very happy with the purchase.
|
Forum: Model A (1928-31)
07-16-2023, 03:36 PM
|
Replies: 34
Views: 2,614
|
Forum: Model A (1928-31)
07-16-2023, 03:11 PM
|
Replies: 34
Views: 2,614
Re: Push button starter
Know what woofa? That's not a bad idea. And that made me remember that I might have a key switch that would work! Going to look for it now.
|
Forum: Model A (1928-31)
07-16-2023, 01:55 PM
|
Replies: 34
Views: 2,614
Re: Push button starter
Battery charged, the engine starts on the first revolution. Now that I know my electrical is good. I hooked the cut off switch back up. Now I just need to mount the Push button. Thanks for the magnet...
|
Forum: Model A (1928-31)
07-15-2023, 11:42 PM
|
Replies: 34
Views: 2,614
Re: Push button starter
Update. I found the short in the system. The original starter switch housing was shorting to the terminal post. I installed a makeshift grommet while I order parts.
I upgraded the battery cables...
|
Forum: Model A (1928-31)
07-15-2023, 11:41 AM
|
Replies: 34
Views: 2,614
Re: Push button starter
Got my gauges wrong. Long nights with my head upside-down trying to fix this.
I meant the I have 4 gauge. Swapping with 2.
|
Forum: Model A (1928-31)
07-15-2023, 10:25 AM
|
Replies: 34
Views: 2,614
Re: Push button starter
This is the solenoid. It has three terminals. And has 6v stamped on the back.
Duralast Solenoid Switch F1490
I see that I do have a 2 gauge battery cable. I'll try swapping that out with 4...
|