Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 60
Search took 0.01 seconds.
Search: Posts Made By: sofield
Forum: Model A (1928-31) 01-12-2021, 01:30 PM
Replies: 10
Views: 543
Posted By sofield
Re: Steering Free Play Update

Adjust the plug so it is flush and one additional turn until the cotter pin can be installed.
Forum: Model A (1928-31) 01-11-2021, 08:50 AM
Replies: 19
Views: 1,187
Posted By sofield
Re: emergency brake backing plate removal

Did you remove the key in the keyway after you removed the emg arm?
Forum: Model A (1928-31) 01-01-2021, 03:16 PM
Replies: 2
Views: 365
Posted By sofield
Clutch finger adjustment

When trying to adjust the fingers on the clutch plate, is the plate bolted to the flywheel and disc and the adjustment being between 5/8 & 11/16 after final adjustment Your answers are appreciated.
Forum: Model A (1928-31) 01-01-2021, 02:47 PM
Replies: 15
Views: 1,203
Posted By sofield
Re: Engine heat in cold weather

How did you arive that there was a difference in the engine temperature with the heater on or off? Are you running a temperature gangue?
Forum: Model-A 12-30-2020, 08:59 PM
Replies: 0
Views: 269
Posted By sofield
Engine Test Stand or Drawings

Looking to purchase a Model "A" engine test or drawings to build one.
Your response is appreciated.
Forum: Model A (1928-31) 12-06-2020, 08:52 AM
Replies: 26
Views: 1,704
Posted By sofield
Re: Bad Stud thread

Bratton's supplies a tool jig kit #8235 that allows you to drill out the stud without disturbing or removing any of the other studs. The jig comes with a locating guide and bushings, a burr to center...
Forum: Model A (1928-31) 11-22-2020, 05:55 PM
Replies: 12
Views: 1,017
Posted By sofield
Re: Ignition System Question

1.5 OHM for 6 volt, 3.OHM for 12 volt
Forum: Model A (1928-31) 11-19-2020, 12:25 PM
Replies: 3
Views: 580
Posted By sofield
Re: Clutch finger depth

Is the 11/16 measurement with the plate and disc bolted to flywheel?
Thanks for a response.
Forum: Model-A 10-30-2020, 03:45 PM
Replies: 0
Views: 423
Posted By sofield
Used Model "A" Engine

I bought a used running engine sight unseen for a project car. The car owner changed his mind and decided on a rebuilt engine. After I received the engine prior to the customer changing his mind I...
Forum: Model-A 10-28-2020, 06:23 PM
Replies: 0
Views: 316
Posted By sofield
Pair of 30 and 31 Rear Fenders

For Pickup/Roadster/Coupe. Original very good condition. no dents / excellent beads / no rips. Sand/prime/paint and put on your car. Shipping additional or pick up.
Forum: Model-A 10-17-2020, 03:38 PM
Replies: 0
Views: 364
Posted By sofield
Front cross member 30-31

Cross member front for 30-31 in good original condition. Bought one from a Barn member
Forum: Model A (1928-31) 10-02-2020, 07:05 PM
Replies: 3
Views: 574
Posted By sofield
Re: wrong / worn axle shims

Place the shim in the hub first that way the shim won't slide off the taper.
Forum: Model A (1928-31) 09-26-2020, 10:48 AM
Replies: 36
Views: 5,247
Posted By sofield
Re: Exhaust Manifold to Tailpipe gasket

Nobody has mentioned to loosen the tail pipe bracket at the rear to help with the alignment. This allows for a forward and rotational movement of the pipe.
Forum: Model A (1928-31) 09-23-2020, 05:51 PM
Replies: 3
Views: 494
Posted By sofield
Door striker plate screws on coupe

I want to replace the striker plate screws on a 30 coupe. My question is are the nuts on the screws captured? I don't want to find out the hard way.
All help is appreciated.
Forum: Model A (1928-31) 08-15-2020, 07:12 PM
Replies: 7
Views: 440
Posted By sofield
Alternator over charges

Alternator puts out 20 amps with a full charged battery. What's the cause
Forum: Model A (1928-31) 07-21-2020, 09:51 AM
Replies: 20
Views: 1,428
Posted By sofield
Re: Shifter spring compressor

I like your idea as the spring is totally contained by the rod and washers, expanded on your idea I would use a washer just a little larger then the OD of the spring and cut three notches equal...
Forum: Model A (1928-31) 07-15-2020, 05:18 PM
Replies: 9
Views: 732
Posted By sofield
Model “A” Bucking at 45 mph plus

Model “A” Bucking at 45 mph plus
The car is a “A” with indented firewall with a “B” engine, “A” head, converted to 12V, running a “B” carb and “B” distributor, 3.0-ohm coil, new condenser, cleaned...
Forum: Model A (1928-31) 04-13-2020, 04:39 PM
Replies: 21
Views: 1,734
Posted By sofield
Re: Pilot bearing fit

Anew bearing has an id of .670 Trans input shaft should be between .667 to .669
Forum: Model A (1928-31) 02-18-2020, 08:40 PM
Replies: 10
Views: 1,121
Posted By sofield
Re: Switching Engine, Reusing Flywheel

I agree with conaway, but don't forget replacing the pilot bearing also.
Forum: Model A (1928-31) 12-26-2019, 09:34 AM
Replies: 3
Views: 881
Posted By sofield
Re: Shackle Bore Alignment

Since you have the spring in place leave the u-bolts loose which will give the spring a little movement to shift as you install shackles. Then with the spring spreader in place go back tighten the...
Forum: Model A (1928-31) 11-11-2019, 03:32 PM
Replies: 38
Views: 2,487
Posted By sofield
Re: 8 volt battery in 6 volt car

I am just looking for a knowledge based cause and effect of this set up has on the various electrical components of a Model A.
Sofield
Forum: Model A (1928-31) 11-10-2019, 05:30 PM
Replies: 38
Views: 2,487
Posted By sofield
8 volt battery in 6 volt car

If using a 8 Volt battery what is the effect on all the 6 volt parts?
Starter motor, all bulbs, coil, generator, horn, 6 volt signal stat, ammeter etc.
Your answers are appreciated.
Forum: Model A (1928-31) 11-07-2019, 07:25 PM
Replies: 35
Views: 3,803
Posted By sofield
Re: Club Thinning

I would like to see our club use a number of these suggestions to recruit new members
sofield
Forum: Model A (1928-31) 01-27-2019, 06:46 PM
Replies: 15
Views: 1,593
Posted By sofield
Re: Headlight wiring

If you don't have the tabs on the lower part of the radiator use black cable ties going through the core and fasten on the front side of the radiator.
Sofield
Forum: Model A (1928-31) 01-24-2019, 08:23 PM
Replies: 13
Views: 1,773
Posted By sofield
Re: Bad manifold gaskets

I will make the assumption that you are using gland rings in the four exhaust ports and the rings won’t allow the manifold to seat properly between the manifold and block causing the gasket to leak...
Showing results 1 to 25 of 60

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:19 AM.