Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.05 seconds.
Search: Posts Made By: Andy
Forum: Early V8 08-06-2020, 04:40 PM
Replies: 1
Views: 254
Posted By Andy
Forum: Early V8 07-27-2020, 11:05 AM
Replies: 2
Views: 258
Posted By Andy
Forum: Early V8 07-20-2020, 03:47 PM
Replies: 2
Views: 258
Posted By Andy
Forum: Early V8 (1932-53) 07-20-2020, 02:05 PM
Replies: 11
Views: 426
Posted By Andy
Re: Original 32 lifters with 8BA vlaves

Thanks, I was hoping one of the rebuilder experts would chime in. Maybe I will cut one up and see how much material is under the top.
Forum: Early V8 (1932-53) 07-20-2020, 10:19 AM
Replies: 11
Views: 426
Posted By Andy
Original 32 lifters with 8BA vlaves

I am thinking of using the original lifters but would be using the later valves. I have seen lifters with a reduced area where the valve hits. Are they required or can I have the original lifters...
Forum: Early V8 07-17-2020, 04:57 PM
Replies: 2
Views: 258
Posted By Andy
Fuel pump,32 Rumble step,59a Caps

32 rumble seat step bracket. Never a repair but some loss due to rust. It would be easy to fill. I believe the repo's are cast iron. This is original Henry Ford steel.--$50
Set of 81- main caps for...
Forum: Early V8 07-11-2020, 09:35 AM
Replies: 1
Views: 254
Posted By Andy
NOS 32 35 cluster gear

New old stock cluster gear. No damage. Tooth count 28/25/18/15
Forum: Early V8 06-22-2020, 11:30 AM
Replies: 0
Views: 110
Posted By Andy
32-33 D L carbs

I have a box of D L carbs. All need work but are complete less the little springs.
Forum: Early V8 06-22-2020, 11:27 AM
Replies: 0
Views: 91
Posted By Andy
32 brake bellcrank

Good condition but the spring has a broken tang. A new one could be made from model airplane music wire
Forum: Early V8 06-22-2020, 11:24 AM
Replies: 0
Views: 130
Posted By Andy
Delete

Delete
Forum: Early V8 06-17-2020, 03:23 PM
Replies: 0
Views: 96
Posted By Andy
Forum: Early V8 (1932-53) 06-11-2020, 06:32 PM
Replies: 3
Views: 243
Posted By Andy
Re: Fuel pumps ?

Try to suck on the discharge port and see if you can pull a vacuum that does not leak. You can put soapy water on it and blow in the inlet port to check for leaks.
Forum: Early V8 06-06-2020, 02:10 PM
Replies: 0
Views: 116
Posted By Andy
32-38 Synchronizer

Offered is a really nice early synchronizer.. The brass synchro rings have little or no wear. The indicater dimples look like a NOS unit I saw. The synchro pads have a step which I thought was from...
Forum: Early V8 06-04-2020, 06:09 PM
Replies: 0
Views: 108
Posted By Andy
SOLD Model B 4 cyl Fuel Pump SOLD

I have a new fuel pump for a Model B. It started out as something else but the only important difference was the actuating lever. I had a busted original pump. I changed out the lever so it is now a...
Forum: Early V8 (1932-53) 06-03-2020, 06:14 PM
Replies: 28
Views: 1,716
Posted By Andy
Re: Installing Starter motor

I put masking tape on the starter case and the bell housing. I put alignment marks on them so I could line the case up so the bolts could be started. It sure made it easier for me to install the...
Forum: Early V8 (1932-53) 05-31-2020, 08:12 PM
Replies: 13
Views: 513
Posted By Andy
Re: King pin bolts 1932

I have used two sets of 32 king pins over the years. I just cut the cups off leaving a ledge to support the bearing. Worked just fine. A friend tried the needle bearings. He did not think it worked...
Forum: Early V8 05-31-2020, 03:11 PM
Replies: 0
Views: 301
Posted By Andy
Delete

Delete
Forum: Early V8 (1932-53) 05-23-2020, 06:13 PM
Replies: 3
Views: 469
Posted By Andy
Re: Fuel pumps ?

Humbly, The bigger diameter pumps were 33-35 then? I had it in my mind the small pumps were early. Thanks.
Forum: Early V8 (1932-53) 05-21-2020, 08:54 AM
Replies: 12
Views: 574
Posted By Andy
Re: Plugging the fuel pump pushrod without a bushing?

I agree with 19Forty. The small hole will help to oil the cam bearing. Plugging the bushing will do nothing as the pushrod does not seal anything. They fit very loose.
Forum: Early V8 05-20-2020, 05:33 PM
Replies: 0
Views: 407
Posted By Andy
delete

Delete
Forum: Early V8 05-20-2020, 05:15 PM
Replies: 0
Views: 461
Posted By Andy
Delete

Delete
Forum: Early V8 05-20-2020, 05:10 PM
Replies: 0
Views: 330
Posted By Andy
Forum: Early V8 (1932-53) 05-15-2020, 05:49 PM
Replies: 2
Views: 210
Posted By Andy
Re: ID Fuel Pump

No number on the lever but 570 is stamped on the mounting flange.
Forum: Early V8 (1932-53) 05-15-2020, 03:48 PM
Replies: 2
Views: 210
Posted By Andy
ID Fuel Pump

I am trying to screw this pump up. Can anyone ID what it's application was? It started when I thougft I could repair the base on a Model B 4cyl pump. It looked identical but the lever was wrong and...
Forum: Early V8 (1932-53) 05-15-2020, 01:16 PM
Replies: 20
Views: 776
Posted By Andy
Re: 1932 Ford roadster size question.

My roadster is a hot rod. The seat bottom was lowered and the back pushed back partially under the rim. Nothing original was cut. It is still hard to get in. Once in, it is fine. I have driven 900...
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 12:58 AM.