Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.07 seconds.
Search: Posts Made By: richard crow
Forum: Early V8 (1932-53) Yesterday, 07:03 AM
Replies: 7
Views: 284
Posted By richard crow
Re: 40`Ford Brakes Update from 7/10 post

is the pedal hard or spongy if it,spongy air in system. if it,s hard it,s a adjustment problem of some kind. master push rod ,shoe anchor adj. cam adj to name a few
Forum: Early V8 (1932-53) 07-08-2020, 06:51 PM
Replies: 12
Views: 452
Posted By richard crow
Re: 1936 Windshield regulator searched

joe,s antique auto in mass has them
Forum: Early V8 (1932-53) 07-06-2020, 05:57 PM
Replies: 5
Views: 238
Posted By richard crow
Re: 59 AB crankshaft timing gear replacement, Help

the crank gear can be removed with crank in eng. the oil pan has to be removed. a simple two leg gear puller will pull the gear they come off ez
Forum: Early V8 (1932-53) 06-24-2020, 11:10 AM
Replies: 2
Views: 360
Posted By richard crow
carlise

did any one go was there a lot of people there were there a lot of venders
Forum: Early V8 (1932-53) 06-24-2020, 11:04 AM
Replies: 23
Views: 576
Posted By richard crow
Re: Problems starting when hot

do they have reg gas in russia or the ethnal crap if you pushed it & it started it might have flooded or the gas boiled
Forum: Early V8 (1932-53) 06-24-2020, 11:00 AM
Replies: 24
Views: 621
Posted By richard crow
Re: Charging Problem

are you checking this with a volt meter on the batt od sol have two windings one for pulling in in the other to hold if it,s staying on pull it uses more current .do this simple test run eng at a...
Forum: Early V8 (1932-53) 06-20-2020, 07:03 AM
Replies: 38
Views: 1,860
Posted By richard crow
Re: Spring Carlisle

the question is was there any old ford stuff there was it worth going to
Forum: Early V8 (1932-53) 06-20-2020, 06:55 AM
Replies: 25
Views: 1,022
Posted By richard crow
Re: Silicone brake fluid

if you are converting to dot 5 make sure all your lines & fittings are super tight. dot 5 can find a leak where there was none before.
Forum: Early V8 (1932-53) 06-19-2020, 07:50 AM
Replies: 13
Views: 331
Posted By richard crow
Re: 1950 Rearend Disassembly

flatford8 has it right just make sure there are not some of those copper washeres on the studs
Forum: Early V8 (1932-53) 06-11-2020, 06:57 AM
Replies: 23
Views: 992
Posted By richard crow
Re: 40 Coupe won't wake up from winter sleep

i just had a car in the shop with the same problem low vacuum no power low compresion after all checks i removed the cam cover i found the cam gear had moved from it,s mark on the cam shaft you can...
Forum: Early V8 (1932-53) 06-10-2020, 02:13 PM
Replies: 19
Views: 691
Posted By richard crow
Re: More. Brake problems

make sure piston is not stuck at the end of it,s stroke. is it a foren make if yes it could be your problem
Forum: Early V8 (1932-53) 06-10-2020, 02:07 PM
Replies: 17
Views: 607
Posted By richard crow
Re: Brake fluid gone..

in the master cyl there is a check valve it,s purpose is to keep low pressure in the system. if the car sits for a long period of time it bleeds off .the wheel cyls relax & leak no car was built to...
Forum: Early V8 (1932-53) 06-07-2020, 07:24 PM
Replies: 19
Views: 869
Posted By richard crow
Re: 12v Headlight problem

when you are on low beam one filerment is lit when you go to high beam both filerments are lit.
Forum: Early V8 (1932-53) 06-04-2020, 08:18 AM
Replies: 18
Views: 573
Posted By richard crow
Re: Disc brake question

check the freeplay in the master cyl if you have a vacuum booster check for play between booster & master cyl if these are not right when the fluid warms up it cant return to the master cyl reservor ...
Forum: Early V8 (1932-53) 06-03-2020, 07:06 AM
Replies: 25
Views: 709
Posted By richard crow
Re: Spongy Brakes

the correct master cyl has a check valve inside it if you are using some kind of master cyl. that don,t have one. the purpose of the check is to hold low pressure in the system other wise when the...
Forum: Early V8 (1932-53) 05-29-2020, 09:03 AM
Replies: 1
Views: 276
Posted By richard crow
carlie

any word on the carlie meet
Forum: Early V8 (1932-53) 05-28-2020, 07:43 AM
Replies: 20
Views: 802
Posted By richard crow
Re: Source for valve spring shims

what do you need them fore the higher the spring pressure the more load on the camshaft & lifters let us know how maney times you put your eng over 4,000
Forum: Early V8 (1932-53) 05-28-2020, 07:35 AM
Replies: 3
Views: 407
Posted By richard crow
Re: Where the V-8 National Meet for 2021?

lets hope hershey is still on
Forum: Early V8 (1932-53) 05-28-2020, 07:34 AM
Replies: 19
Views: 750
Posted By richard crow
Re: New Clutch Slipping

what is your rear end gearing if it,s high when your in fith it,s even higher.if all clerance checks out send pressure plate to fort wayne clutch have them increase spring pressure
Forum: Early V8 (1932-53) 05-28-2020, 06:22 AM
Replies: 4
Views: 483
Posted By richard crow
Re: Flathead Cylinder Heads

you new to the flat head engine if you want a nice smooth running eng leave it stock enjoy it the way it was desigened
Forum: Early V8 (1932-53) 05-24-2020, 02:03 PM
Replies: 13
Views: 820
Posted By richard crow
Re: Almost a fire in the 36

get the one with a dioed
Forum: Early V8 (1932-53) 05-24-2020, 07:42 AM
Replies: 94
Views: 3,545
Posted By richard crow
Re: white steam from breather and water tailpipe

look at those studs there some type of after market the shoulders seem very long are you using stock heads or alum heads if the shoulder is to long you will get torque reading but gasket will not be...
Forum: Early V8 (1932-53) 05-23-2020, 07:02 AM
Replies: 3
Views: 269
Posted By richard crow
Re: Rear main oil drain pipe size

they have a special thread i have found it,s the same as some the thread used in electic lamps where the bulb scocket screws on i just get a lenth & cut the lenth i need opisit the thread
Forum: Early V8 (1932-53) 05-22-2020, 07:16 PM
Replies: 94
Views: 3,545
Posted By richard crow
Re: white steam from breather and water tailpipe

get a can of zotight problem over
Forum: Early V8 (1932-53) 05-22-2020, 06:11 AM
Replies: 94
Views: 3,545
Posted By richard crow
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 12:38 PM.