Forum: Model A (1928-31)
10-29-2021, 07:01 AM
|
Replies: 16
Views: 1,530
|
Forum: Model A (1928-31)
12-26-2020, 08:16 PM
|
Replies: 3
Views: 1,013
Timing
When timing with test light is one notch enough advance timing or should light come on at second notch.
Thanks
Dana
|
Forum: Model A (1928-31)
11-03-2020, 08:11 AM
|
Replies: 10
Views: 1,986
Advance timing
When using test light to time engine is one notch enough advance timing are should timing be advanced for two notches.
Thanks
Dana
|
Forum: Model A (1928-31)
02-15-2018, 10:17 AM
|
Replies: 5
Views: 1,591
Re: float valve
I tried new kit, polishing needle with steel wool, lapping with tooth paste with no result, finally after a year of trials tapped needle with small hammer several times, leak stopped.
Thanks
|
Forum: Model A (1928-31)
12-19-2017, 10:46 PM
|
Replies: 11
Views: 4,072
|
Forum: Model A (1928-31)
11-28-2017, 10:41 PM
|
Replies: 15
Views: 2,773
Re: update on leaking tillitson
My Tillitson leaked for over a year, installed new kit, lap seat with tooth paste, changed float setting from 7/8"-1", took top off carburetor and health in hand, struck needle with small hammer,...
|
Forum: Model A (1928-31)
05-26-2016, 12:56 PM
|
Replies: 2
Views: 1,477
Horn sound while driving
My horn sounds as good as any i have heard while parked but when driving it does not sound that good, any solutions.
Thanks
Dana
|
Forum: Model A (1928-31)
05-25-2016, 10:42 AM
|
Replies: 7
Views: 2,467
shut off valve
Does any of the suppliers sale a ball valve for under tank shut off instead of the tapered 1/4 mpt x 3/8 flared valve.
Thanks
Dana
|
Forum: Model A (1928-31)
05-24-2016, 05:59 PM
|
Replies: 22
Views: 7,067
|
Forum: Model A (1928-31)
05-24-2016, 05:55 PM
|
Replies: 17
Views: 3,696
Re: Spartan horn
My horn sounds perfect setting but while driving it does not sound good at times.
Dana
|
Forum: Model A (1928-31)
05-24-2016, 07:33 AM
|
Replies: 22
Views: 7,067
|
Forum: Model A (1928-31)
09-10-2015, 01:08 PM
|
Replies: 12
Views: 1,873
Re: oil drip
Has been leaking four years, same weight and amount of oil that i have been using.
Thanks
Dana
|
Forum: Model A (1928-31)
09-10-2015, 05:07 AM
|
Replies: 12
Views: 1,873
oil drip
My 31 coupe has always dripped a little, just noticed last couple weeks no drips after oil change, filler cap has been pushed down to far is only thing i can think of any other opinions.
Thanks
Dana
|
Forum: Model A (1928-31)
08-29-2015, 06:28 AM
|
Replies: 19
Views: 3,965
|
Forum: Model A (1928-31)
08-23-2015, 02:42 PM
|
Replies: 11
Views: 2,297
Re: Red wire on coil
Thanks Mitch: Mine is + ground and was wired right, had read some were it would give about 15% more on top end.
Thanks Everyone
Dana
|
Forum: Model A (1928-31)
08-23-2015, 11:28 AM
|
Replies: 11
Views: 2,297
Red wire on coil
My: Coil is marked + & - which side does red switch wire connect to?
Thanks
Dana
|
Forum: Model A (1928-31)
08-11-2015, 04:36 PM
|
Replies: 5
Views: 1,983
Re: Radiator over flow
Thanks Bill already in there, I cant see connection to new plugs, but number four plug got hotter than the others, enough to change color of plug to blue tint.
Thanks
|
Forum: Model A (1928-31)
08-11-2015, 11:22 AM
|
Replies: 5
Views: 1,983
Radiator over flow
Replaced TT10 with W18, went for four mile drive had some radiator over flow, haven't been having this problem, number four plug had some discolor on out side of plug, TT10 were some sooting up. any...
|
Forum: Model A (1928-31)
08-10-2015, 04:41 PM
|
Replies: 7
Views: 2,456
Re: spark plug connectors
Also the W18 is about 1/8" longer than the TT10 from the washer to the tip, this is no problem with hitting the piston?
Thanks
Dana
|
Forum: Model A (1928-31)
08-10-2015, 03:13 PM
|
Replies: 7
Views: 2,456
spark plug connectors
Pack up set of Champion W18 plugs, will plug connectors work with them look a lot taller than TT10 I have in my 31 coupe now
Thanks
Dana
|
Forum: Model A (1928-31)
08-04-2015, 12:15 PM
|
Replies: 13
Views: 2,549
Re: Gas gauge gaskets
Thanks Tom: mine had two brass rings and did use cork all the way. Took longer to clean up tank flange than to take apart and put back together. Haven't filled up with gas yet, gauge works and looks...
|
Forum: Model A (1928-31)
08-03-2015, 09:17 PM
|
Replies: 13
Views: 2,549
Re: Gas gauge gaskets
Forever4: I would think were the metal face plate would not be next to glass.
Thanks
|
Forum: Model A (1928-31)
08-03-2015, 04:53 PM
|
Replies: 13
Views: 2,549
|
Forum: Model A (1928-31)
08-03-2015, 04:24 PM
|
Replies: 13
Views: 2,549
Gas gauge gaskets
Does any one have a picture of the correct order in witch gaskets face plate and glass go in model a gas gauge also how many brass rings go under large nut.
Thanks
|
Forum: Model A (1928-31)
04-06-2015, 06:52 PM
|
Replies: 16
Views: 4,785
Re: horn rod too tight...
My steering column had a burr in the top three inches, ran a drill in it and smoothed it up.
Thanks
Dana
|