Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 25 of 500
Search took 0.06 seconds.
Search: Posts Made By: 41ford1
Forum: Early V8 (1932-53) 07-31-2022, 03:58 PM
Replies: 3
Views: 669
Posted By 41ford1
Re: Tooth count

32/9 = 3.55:1
11/39= 3.54:1
The diff in the avatar is marked 11 39 and checked put to 3.54:1.
Forum: Early V8 (1932-53) 07-31-2022, 03:52 PM
Replies: 6
Views: 862
Posted By 41ford1
Re: front motor mount cushions

The Bob Drakes mounts are the best. The Speedway mounts do not have the cupped base washer. There is nothing to prevent the cushion from expanding and flattening under load.
Forum: Early V8 (1932-53) 12-26-2021, 09:51 AM
Replies: 11
Views: 2,154
Posted By 41ford1
Re: Jump starting a 12V Positive Ground

No problem for a push start. You will have a short circuit when you try to connect the positive posts. Many sparks and possibly a battery explosion.
Forum: Early V8 (1932-53) 12-18-2021, 11:59 AM
Replies: 27
Views: 2,723
Posted By 41ford1
Re: another great barner gone

Rest in peace Bill. You will be missed. I first met Bill at the Barners bash in 2010.

Jeff, this is the tool Bill made for the OP sensor.
Forum: Early V8 (1932-53) 10-22-2021, 02:05 PM
Replies: 13
Views: 1,480
Posted By 41ford1
Re: Oil Pressure Sender

drolston

I would say the one you got is defective.
Forum: Early V8 (1932-53) 10-21-2021, 11:21 AM
Replies: 9
Views: 918
Posted By 41ford1
Re: 40 Ford 1/2 ton pick up trans removal.

V8Coopman, Would those have been on Tonner and larger trucks?
Forum: Early V8 (1932-53) 10-21-2021, 11:13 AM
Replies: 9
Views: 918
Posted By 41ford1
Re: 40 Ford 1/2 ton pick up trans removal.

I did a clutch replacement last year on the avatar pickup. The trans can be removed from the floor access. The rear end and drive shaft has to be move back about 6" so you have enough room to pull...
Forum: Early V8 (1932-53) 10-01-2021, 01:43 PM
Replies: 12
Views: 1,476
Posted By 41ford1
Re: Dimension for offset on cam drive.

Mart, These dimensions are for the adaptor button that is in my manuals CD. I think they give the info you are looking for.
Chuck
Forum: Early V8 (1932-53) 09-27-2021, 06:26 PM
Replies: 13
Views: 1,480
Posted By 41ford1
Re: Oil Pressure Sender

A Standard Motor Products PS60 has been on my 59AB in the pickup for 12 years. Verified it with a mechanical gauge.
Forum: Early V8 (1932-53) 09-24-2021, 01:34 PM
Replies: 8
Views: 1,774
Posted By 41ford1
Re: 1939/1940 ford grille

Here is a better pic of the 40 Standard/pickup grille.
Forum: Early V8 (1932-53) 09-24-2021, 01:16 PM
Replies: 8
Views: 1,774
Posted By 41ford1
Re: 1939/1940 ford grille

39 deluxe.
40 standard/pickup has a wider center bar. Link to the front pic of my pickup below.
https://www.fordbarn.com/forum/album.php?albumid=2248&pictureid=18361
Forum: Early V8 (1932-53) 08-10-2021, 07:54 AM
Replies: 18
Views: 1,852
Posted By 41ford1
Re: OK, so it is older

If you stop, you KNOW it will follow you home.
Forum: Early V8 (1932-53) 05-08-2021, 08:44 AM
Replies: 11
Views: 1,832
Posted By 41ford1
Re: Mart's Update 2021 Episode 19 Part 1&2: The 32 Sedan body goes on!

Good job getting all of that done alone. I don't know if I would have been as fussy about the hardware as you were. I agree with mfirth. Take us for a ride.
Forum: Early V8 05-08-2021, 08:27 AM
Replies: 19
Views: 5,798
Posted By 41ford1
Forum: Early V8 (1932-53) 04-25-2021, 08:35 AM
Replies: 4
Views: 649
Posted By 41ford1
Re: visor

Check this thread: https://www.fordbarn.com/forum/showthread.php?t=203088

The screws are #12 X 1 1/2" on the sides. I believe they are the same on the center bracket. I have not removed that to...
Forum: Early V8 03-13-2021, 08:59 AM
Replies: 19
Views: 5,798
Posted By 41ford1
Forum: Early V8 (1932-53) 10-05-2020, 01:24 PM
Replies: 10
Views: 1,383
Posted By 41ford1
Re: 1941 Pickup Interior Install Help

This kit came from Dennis Carpenter. The only place the needed trimming was over the windshield header. The headliner panel slides between the roof and the header. I had to trim about 3/8" off the...
Forum: Early V8 09-29-2020, 10:55 PM
Replies: 19
Views: 5,798
Posted By 41ford1
Forum: Early V8 (1932-53) 09-25-2020, 03:22 PM
Replies: 23
Views: 2,526
Posted By 41ford1
Re: New Rebuild Overheating

How did you set the timing? A stock 59 engine has no timing marks. I have a 59 in my pickup. I had to use a vacuum gauge to set the timing because I have a Mallory electronic distributer. I had...
Forum: Early V8 09-07-2020, 10:44 AM
Replies: 19
Views: 5,798
Posted By 41ford1
Forum: Early V8 08-02-2020, 03:31 PM
Replies: 19
Views: 5,798
Posted By 41ford1
Forum: Early V8 (1932-53) 07-17-2020, 10:18 AM
Replies: 36
Views: 3,565
Posted By 41ford1
Re: Where does your 53 Ford run?

My Courier runs in the same range. It's a 6 not a V8.
Forum: Early V8 (1932-53) 07-15-2020, 02:32 PM
Replies: 3
Views: 1,122
Posted By 41ford1
Re: Possible fishing scam

He posted that he is looking for front end alignment tools.
https://www.fordbarn.com/forum/showthread.php?t=284082
Forum: Early V8 (1932-53) 06-10-2020, 09:43 PM
Replies: 2
Views: 942
Posted By 41ford1
Re: Door stay diagram for 53 Courier

Rich,
That would help

Thanks
Forum: Early V8 (1932-53) 06-10-2020, 04:45 PM
Replies: 2
Views: 942
Posted By 41ford1
Door stay diagram for 53 Courier

Does any one have a diagram for the door stay on the rear door of a Courier?
I believe the one on mine is missing some parts.

Thanks in advance.
Showing results 1 to 25 of 500

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:45 AM.