Forum: Model A (1928-31)
12-04-2019, 03:51 PM
|
|
Replies: 3
Views: 343
Re: Sp. Plug thread cleaning
When I find it necessary to clean threads, I have loaded the tap with stiff grease to capture the debris. Fully fill the taps cutting area and the openings between the cutting surfaces. I turn in...
|
|
Forum: Model A (1928-31)
11-16-2019, 09:33 AM
|
|
Replies: 5
Views: 418
Re: Valves
I use the single lock tappets and don't have an issue adjusting them. Double lock are more work than single lock but with the correct wrenches not difficult. I have ground a couple open end wrenches...
|
|
Forum: Model A (1928-31)
11-14-2019, 08:23 AM
|
|
Replies: 4
Views: 289
Re: 32 B4 rear seal missing
For a good reproduction of the original: Snyder's has them in their offerings: Rear main oil seal B-6335
Another option that I most often use on a B block is the Small Block Chevy (SBC) rear...
|
|
Forum: Model A (1928-31)
11-11-2019, 03:49 PM
|
|
Replies: 3
Views: 278
Re: FS ignition timing
I run my Lion Speed Head, milled .074", at 24 degrees advance and still need to be careful when climbing hills to avoid lugging and the resulting pinging. Downshifting to raise the rpm solves the...
|
|
Forum: Model A (1928-31)
11-11-2019, 03:43 PM
|
|
Replies: 12
Views: 842
Re: Hot Driver
I installed a Ken Davis unit in my '31 Slant Windshield. I am well satisfied with the way it works. I only notice a drop in engine RPM at idle. It was not difficult to install.
Good Day!
|
|
Forum: Model A (1928-31)
11-04-2019, 04:07 PM
|
|
Replies: 13
Views: 660
|
|
Forum: Model A (1928-31)
10-29-2019, 07:07 PM
|
|
Replies: 20
Views: 1,685
|
|
Forum: Model A (1928-31)
10-24-2019, 04:16 PM
|
|
Replies: 32
Views: 1,326
Re: 6V versus 12V (stupid ques. I'm a newbie)
Unless you have a compelling reason to change, I suggest staying with 6 volt positive ground. Most technical articles for the maintenance of the Model A assume the car is wired as original (6 volt)...
|
|
Forum: Model A (1928-31)
10-09-2019, 04:18 PM
|
|
Replies: 3
Views: 471
|
|
Forum: Model A (1928-31)
09-26-2019, 05:54 AM
|
|
Replies: 41
Views: 1,954
|
|
Forum: Model A (1928-31)
09-13-2019, 05:49 AM
|
|
Replies: 17
Views: 900
|
|
Forum: Model A (1928-31)
09-12-2019, 04:37 PM
|
|
Replies: 17
Views: 900
Re: Air conditioning in a open car
I have a Phaeton and a '31 S/W with the air conditioner alexiskai describes. Based on the output of the unit I have, the blast of cool air from the AC unit would help you to feel cooler if installed...
|
|
Forum: Model A (1928-31)
09-12-2019, 07:53 AM
|
|
Replies: 3
Views: 468
Re: Insert con rod suggestions
I have had good service from Antique Engine Rebuilding (AER) inserted rods on many engines. Mostly mild but a few hot A's and B's were built and are providing good service with these AER rods.
...
|
|
Forum: Model A (1928-31)
09-10-2019, 07:54 AM
|
|
Replies: 19
Views: 881
|
|
Forum: Model A (1928-31)
09-02-2019, 08:50 AM
|
|
Replies: 46
Views: 2,258
Re: T-5 5 speed trans VS Mitchell overdrive
Soild cam plunger stop: The high capacity oil pump, a tight oil pump drive gear, fuel pump, varying lifter loads or a tight distributor can all cause the cam to move forward. The solid stop is a...
|
|
Forum: Model A (1928-31)
08-31-2019, 04:57 PM
|
|
Replies: 46
Views: 2,258
|
|
Forum: Model A (1928-31)
08-31-2019, 03:07 PM
|
|
Replies: 46
Views: 2,258
Re: T-5 5 speed trans VS Mitchell overdrive
Ken, You ask how to produce 80 HP without an overhead valve head. 80 HP is my goal for a touring car I am building up. I am currently dyno breaking in a B block that has full oil pressure and is...
|
|
Forum: Model A (1928-31)
08-29-2019, 06:08 AM
|
|
Replies: 30
Views: 2,031
|
|
Forum: Model A (1928-31)
08-28-2019, 05:04 PM
|
|
Replies: 30
Views: 2,031
|
|
Forum: Model A (1928-31)
08-28-2019, 08:00 AM
|
|
Replies: 46
Views: 2,258
Re: T-5 5 speed trans VS Mitchell overdrive
I have experience with the Mitchell and the T-5.
I have a Mitchell in my '29 Phaeton and have driven it over 95,000 miles. No issues and very durable. I like the splitter and have become...
|
|
Forum: Model A (1928-31)
08-22-2019, 04:17 PM
|
|
Replies: 21
Views: 1,334
|
|
Forum: Model A (1928-31)
08-22-2019, 02:46 PM
|
|
Replies: 21
Views: 1,334
Re: Shock Absorbers
Paul, I interpreted his reference and question as to "shock arms". That was what he said. I saw your question and thought the same about your request. I did not know how we got to discussing the...
|
|
Forum: Model A (1928-31)
08-21-2019, 02:06 PM
|
|
Replies: 21
Views: 1,334
Re: Shock Absorbers
Same for me on the Stipe shocks. I have two cars with them and find they do a very good job. Good Day!
|
|
Forum: Model A (1928-31)
08-21-2019, 02:04 PM
|
|
Replies: 9
Views: 654
Re: What to do w Virginia?
If you can devote a full day to it, the Skyline Drive is about 120 miles from you. The drive is awesome with great views. The full drive is a bit over 100 miles.
Good Day!
|
|
Forum: Model A (1928-31)
08-12-2019, 02:29 PM
|
|
Replies: 6
Views: 531
|
