Forum: Model A (1928-31)
08-26-2020, 02:56 PM
|
|
Replies: 12
Views: 1,531
Re: Model A electric wiper inside mount
I did nearly the same in my car. There is a unit available that has a longer shaft and housing that can be cut down, so a bit less work than you did but it does not have a built in switch. The only...
|
|
Forum: Model A (1928-31)
12-14-2018, 08:34 PM
|
|
Replies: 89
Views: 15,640
|
|
Forum: Model A (1928-31)
12-08-2018, 12:41 AM
|
|
Replies: 217
Views: 42,232
Re: OK! Let's get personal!
I’m 45, got my Model A when I was 13. Dad let me drive his sedan when I was 11- been hooked for a long time.
|
|
Forum: Model A (1928-31)
05-21-2018, 09:23 PM
|
|
Replies: 10
Views: 2,168
Re: Coupe rear window
I am in the middle of adding a roll down rear window kit in my ‘31. They were standard equipment in all deluxe coupes after June if 31 and in standard coupes that had a rumble seat. I have wanted one...
|
|
Forum: Model A (1928-31)
01-22-2018, 09:59 PM
|
|
Replies: 12
Views: 2,982
Re: FRONT Float-a-Motor Mount Questions
It isn’t required to use a front float-a-motor if you are using the rear set up. You can use the crank, in fact I would make sure the crank lines up so that you know the engine is sitting at a...
|
|
Forum: Model A (1928-31)
01-25-2017, 06:54 PM
|
|
Replies: 344
Views: 64,955
|
|
Forum: Model A (1928-31)
04-01-2016, 08:24 PM
|
|
Replies: 42
Views: 6,764
Re: Naming vehicles.
My coupe is named Henry (not very original but that was what the couple I got him from in '86 called him) My dad's sedan is named Abe (it is painted the same color as his '79 Lincoln)
There was a...
|
|
Forum: Model A (1928-31)
02-09-2016, 08:13 PM
|
|
Replies: 17
Views: 4,262
Re: Exhaust manifold heater
I have the same door on my Coupe and it is for an Otwell. I ended up getting a bit of exhaust pipe and cutting it out to fit over the manifold and holding it down with some hose clamps. It probably...
|
|
Forum: Model A (1928-31)
07-25-2013, 07:25 PM
|
|
Replies: 25
Views: 5,699
|
|
Forum: Model A (1928-31)
05-23-2011, 06:05 PM
|
|
Replies: 12
Views: 1,903
Re: HELP Bonniville accomidation.
if you are unable to get rooms in Wendover, rather than stay in Salt Lake it is about 1/2 as many miles to Wells, Nv (60 miles) - still a bit of a drive but it is an option
|
|
Forum: Model A (1928-31)
09-23-2010, 10:11 PM
|
|
Replies: 14
Views: 2,275
|
|
Forum: Model A (1928-31)
07-16-2010, 03:13 PM
|
|
Replies: 26
Views: 6,089
Re: Radio Install?
Here is how I mounted mine - I built a bracket that clamps on to the stiffener that runs i high up on the kick panel (drilled no holes) it also has a lighter socket for the gps you can see.
...
|
|
Forum: Model A (1928-31)
05-29-2010, 10:35 PM
|
|
Replies: 4
Views: 1,793
Re: U-Joint grease fitting
I remember the same discussion / argument, All I can say is based on the location of the grease fitting it is apparent to me that it was intended to lubricate the u-joint primarily and possibly the...
|
|
Forum: Model A (1928-31)
05-25-2010, 09:16 PM
|
|
Replies: 11
Views: 4,081
Re: 1931 RE-stamped firewalls...
Here are a couple of shots of the firewall of my Dad's sedan -- you can easily see the "plug" welded in to fill the old hole for the gas line and the flattening of the ribs
...
|
|
Forum: Model A (1928-31)
05-16-2010, 03:20 AM
|
|
Replies: 788
Views: 381,761
Re: Post a picture of your car...
https://i284.photobucket.com/albums/ll34/bjerg_menneskene/summer2009carclubtour001.jpg
https://i284.photobucket.com/albums/ll34/bjerg_menneskene/summer2009oldcartour003.jpg
...
|
