Forum: Model A (1928-31)
04-02-2020, 09:59 AM
|
Replies: 7
Views: 1,687
|
Forum: Model A (1928-31)
04-01-2020, 09:37 PM
|
Replies: 7
Views: 1,687
One inch wide insert bearings
Pulled and engine apart. Two observations.
1) It has insert bearing on the rods. The inserts were centered in the rod journal but were only one inch wide, not the usual width of the rod.
2)...
|
Forum: Model A (1928-31)
03-26-2019, 08:40 PM
|
Replies: 3
Views: 1,145
|
Forum: Model A (1928-31)
03-26-2019, 08:33 PM
|
Replies: 4
Views: 1,955
|
Forum: Model A (1928-31)
03-22-2019, 01:49 PM
|
Replies: 3
Views: 1,145
Welting on a 29 roadster pickup.
I have a 1929 roadster pickup.
Is beaded welting installed between the door posts and the front quarter panels in the same manner as between the gas tank and the cowl?
At present it does not...
|
Forum: Model A (1928-31)
03-22-2019, 01:35 PM
|
Replies: 4
Views: 1,955
Repairs to top iron nailing material
I believe the original nailing material inside of the top irons of a 1928/29 Model A roadster was leather. I have a set of irons where this material is rotted or missing.
What have folks done to...
|
Forum: Model A (1928-31)
08-20-2018, 08:57 PM
|
Replies: 7
Views: 1,807
Transmission rear main bearing
Transmission parts are installed as per installation schematic how ever I have two questions.
1) When I install the transmission rear main bearing and rear bearing retainer, the rear bearing...
|
Forum: Model A (1928-31)
07-16-2018, 10:48 PM
|
Replies: 7
Views: 1,690
|
Forum: Model A (1928-31)
07-16-2018, 05:13 PM
|
Replies: 7
Views: 1,690
|
Forum: Model A (1928-31)
07-16-2018, 04:46 PM
|
Replies: 7
Views: 1,690
Engine Vaccum readings
What vacuum should a good Model A engine pull at say 40 miles per hour.
At Idle my engine pulls a steady 18. At 35 - 40 it drops to above 10.
|
Forum: Model A (1928-31)
12-09-2017, 09:54 AM
|
Replies: 7
Views: 1,532
Re: Power house generator woes
I went over what I thought I had checked correctly and just as repeated on the forum several times there was bad post connections. Thx again for reinforcing what has already been indicated several...
|
Forum: Model A (1928-31)
12-07-2017, 05:50 PM
|
Replies: 7
Views: 1,532
|
Forum: Model A (1928-31)
12-07-2017, 10:52 AM
|
Replies: 7
Views: 1,532
Re: Power house generator woes
I believe I have done that--does that happen when you hook it to run it like a motor? I have also connected the field separately--- negative to lead and positive to ground as well
I have also...
|
Forum: Model A (1928-31)
12-06-2017, 06:58 PM
|
Replies: 12
Views: 1,848
|
Forum: Model A (1928-31)
12-06-2017, 06:56 PM
|
Replies: 7
Views: 1,532
Power house generator woes
Power house status.
- Hook up to battery. positive to ground negative to the output post- it motors pretty good.
- Field measures about 3.5 ohms
- Growler shows no shorts on the com
- Have...
|
Forum: Model A (1928-31)
02-20-2017, 08:30 PM
|
Replies: 11
Views: 2,405
Hastings 60 rings
I have a set Hastings rings.
One ring is the oil ring for the bottom piston groove.
Of the two remaining compression rings, one has no camfer or bevel on it and no identification on either side....
|
Forum: Model A (1928-31)
05-13-2016, 11:02 PM
|
Replies: 11
Views: 2,298
Re: Charging test question...
You can also bench test it by spinning it with a variable speed drill. You will feel it load up the field and with a voltmeter you will can see the "voltage" out put.
|
Forum: Model A (1928-31)
05-13-2016, 10:59 PM
|
Replies: 9
Views: 2,176
Re: Differential rebuild
Thx all for you responses.
Yes I was going with Tom Endy's procedure. I actually am doing the exact thing he was--using the later banjo and earlier axle housings. His procedure how ever does not...
|
Forum: Model A (1928-31)
05-10-2016, 01:51 PM
|
Replies: 9
Views: 2,176
|
Forum: Model A (1928-31)
05-10-2016, 01:49 PM
|
Replies: 9
Views: 2,176
Re: Differential rebuild
Thx all for your input. have read several articles on the subject, most seem to meet the same objective. The differential is not a mix of parts but does have thicker Timkin bearings as I just found...
|
Forum: Model A (1928-31)
05-09-2016, 06:30 PM
|
Replies: 9
Views: 2,176
Differential rebuild
I took a differential apart.
I installed new bearings etc.
When I put it back together, I ended up with approx. 22 thou of gaskets on each side to get the backlash and preload correct.All the...
|
Forum: Model A (1928-31)
08-09-2015, 10:58 PM
|
Replies: 8
Views: 2,276
6 volt ignition coil failures.
Have installed an electronic ignition system as per instructions on a 1930 model A.
Unit runs well for a few days but eventually the main coil fails.
Replaced coil twice with same results--uhm!...
|
Forum: Model A (1928-31)
07-19-2014, 08:41 PM
|
Replies: 7
Views: 1,775
Re: Hot hot is too hot
Yes the engine was broken in a similar manner as mentioned in the comment of this thread. My basic question is how do they run --- usually.
|
Forum: Model A (1928-31)
07-16-2014, 10:14 PM
|
Replies: 7
Views: 1,775
Hot hot is too hot
New engine, 80 degree day, running 50 - 55 up a hill, reached 200 degree's, on the level at 48 - 55 seems to run between 180 and 190.
Is this normal. I was pushing it to make it work.
|
Forum: Model A (1928-31)
04-01-2014, 09:10 AM
|
Replies: 3
Views: 1,590
|