Forum: Model A (1928-31)
Yesterday, 09:42 AM
|
Replies: 8
Views: 407
|
Forum: Model A (1928-31)
03-26-2024, 06:05 PM
|
Replies: 10
Views: 280
|
Forum: Model A (1928-31)
03-17-2024, 08:03 PM
|
Replies: 7
Views: 503
|
Forum: Model A (1928-31)
03-09-2024, 03:28 PM
|
Replies: 28
Views: 5,157
|
Forum: Model A (1928-31)
03-07-2024, 11:10 AM
|
Replies: 28
Views: 5,157
Re: Main bearing bolts
The original bolts were a snug fit in the block. You would tighten up the nut, after positioning the cotter pin hole in the bolt for best installation. This snugness is what centers the main cap on...
|
Forum: Model A (1928-31)
03-04-2024, 03:08 PM
|
Replies: 73
Views: 4,080
Re: Value of an Un-Restored Model A Engine
Don't scrap them, there may be some good stuff there!! I am running a block that had been laying on the ground outdoors for years, it did need to be bored .100 oversize on the cylinders but it is...
|
Forum: Model A (1928-31)
02-22-2024, 11:21 AM
|
Replies: 17
Views: 941
Re: What the heck just happened ? (electrical)
I agree. Not to pile on here but if the car is positive ground your first connection of ground clamp to head bolt was reverse polarity and electronics usually if not always turn up their toes on that...
|
Forum: Model A (1928-31)
02-21-2024, 03:13 PM
|
Replies: 10
Views: 620
|
Forum: Model A (1928-31)
02-18-2024, 10:49 AM
|
Replies: 6
Views: 583
|
Forum: Model A (1928-31)
02-15-2024, 12:31 PM
|
Replies: 24
Views: 1,176
|
Forum: Model A (1928-31)
02-13-2024, 06:40 PM
|
Replies: 8
Views: 470
|
Forum: Model A (1928-31)
02-11-2024, 11:52 AM
|
Replies: 6
Views: 545
|
Forum: Model A (1928-31)
02-10-2024, 11:00 AM
|
Replies: 27
Views: 1,652
|
Forum: Model A (1928-31)
02-08-2024, 09:44 AM
|
Replies: 63
Views: 5,137
|
Forum: Model A (1928-31)
02-07-2024, 12:11 PM
|
Replies: 22
Views: 1,732
|
Forum: Early V8 (1932-53)
02-05-2024, 06:57 PM
|
Replies: 14
Views: 760
|
Forum: Early V8 (1932-53)
02-05-2024, 04:16 PM
|
Replies: 14
Views: 760
|
Forum: Early V8 (1932-53)
02-05-2024, 03:55 PM
|
Replies: 16
Views: 753
|
Forum: Model A (1928-31)
02-04-2024, 01:02 PM
|
Replies: 28
Views: 1,174
Re: Loss of power,
Distributor well grounded to block, lock bolt and nut tight? Engine, frame and battery all grounded together? The advance lever can act as a ground for distributor.
|
Forum: Model A (1928-31)
01-31-2024, 11:21 AM
|
Replies: 12
Views: 664
|
Forum: Model A (1928-31)
01-30-2024, 04:45 PM
|
Replies: 12
Views: 664
|
Forum: Model A (1928-31)
01-30-2024, 11:18 AM
|
Replies: 30
Views: 2,357
Re: High Compression Head
The "crowfoot" Winfield head is a good one, Jim Brierly's head looks good also. Both of these are different from each other. Harley put a lot of effort into their design making it worthy of...
|
Forum: Model A (1928-31)
01-28-2024, 11:24 AM
|
Replies: 2
Views: 790
|
Forum: Model A (1928-31)
01-13-2024, 11:52 AM
|
Replies: 9
Views: 901
|
Forum: Model A (1928-31)
01-11-2024, 12:17 PM
|
Replies: 6
Views: 791
|