Forum: Early V8 (1932-53)
01-05-2024, 07:06 AM
|
Replies: 2
Views: 369
Dashboard circuit breaker
I have a 1941 pickup with the under dash wiring all cut up and I want to put a new wire harness in so that I don't have all these aftermarket gauges mounted under the dash. The truck was converted to...
|
Forum: Early V8 (1932-53)
12-26-2023, 12:00 PM
|
Replies: 2
Views: 323
heater motor housing
I am looking for a heater blower motor housing, and 12 volt motor for a 1949 F3. It is the one mounted up in the fender well. What I have left is not rebuildable. Does anyone have any sources for...
|
Forum: Early V8 (1932-53)
01-06-2023, 03:12 PM
|
Replies: 8
Views: 1,391
Re: spare tire mount 41 ford pickup
I did a check in the "Green Bible" and on page 12 is a diagram of the spare tire carrier and it shows that 1936 to 1941 commercial, does mount to the running board. There is an attachment to the box...
|
Forum: Early V8 (1932-53)
01-05-2023, 10:02 AM
|
Replies: 8
Views: 1,391
Re: spare tire mount 41 ford pickup
I checked all of the places you mentioned and nobody carries the spare tire mount. I will keep looking on this site and ebay. Thank you for your help so far.
|
Forum: Early V8 (1932-53)
01-04-2023, 01:25 PM
|
Replies: 8
Views: 1,391
spare tire mount 41 ford pickup
I am looking for a spare tire mount for a 1941 Ford 1/2 ton. Specifically the one that mounts through the running board. Is there a source for these new or does anyone know of one for sale?
|
Forum: Early V8 (1932-53)
03-09-2022, 10:59 AM
|
Replies: 3
Views: 610
41 pickup spare tire carrier
I am trying to locate the parts needed for the spare tire carrier for a 1941 pic kup. I am not really sure of all of the parts that are needed for this. Does anyone have any idea where I might look...
|
Forum: Early V8 (1932-53)
08-07-2021, 06:30 AM
|
Replies: 8
Views: 894
Re: 1937 Flathead
The oil pressure is what scares me the most. I have valvoline VR1 20W50 oil in it now.
|
Forum: Early V8 (1932-53)
08-06-2021, 02:01 PM
|
Replies: 8
Views: 894
|
Forum: Early V8 (1932-53)
08-06-2021, 07:53 AM
|
Replies: 8
Views: 894
1937 Flathead
I know this has been discussed earlier BUT, I have a 1937 flathead v8 in a 1941 pickup. The cylinder compression is 60 to 65 psi, dry in all of the cylinders. the oil pressure drops from 20 to 25 psi...
|
Forum: Model A (1928-31)
12-02-2020, 09:16 AM
|
Replies: 5
Views: 1,156
1937 Flathead
What is the best antifreeze to use? Ethylene Glycol or the newer multi use antifreeze. Also on motor oil, what is the best type of oil in the flatheads? a multi viscosity or a straight 30 weight?
|
Forum: Model A (1928-31)
11-12-2020, 07:11 PM
|
Replies: 14
Views: 2,297
Re: 1929 u joint
Mine is the riveted one and the rivets are loose along with everything else. Yes I saw that Mac's offers one so I will go that route. Thanks everyone.
|
Forum: Model A (1928-31)
11-12-2020, 06:39 AM
|
Replies: 14
Views: 2,297
Re: 1929 u joint
So I have just looked in Mac's auto and they offer a new U joint but it states that it will not work with one that is riveted. It so happens that mine has what I would call a riveted cage around it....
|
Forum: Model A (1928-31)
11-11-2020, 06:06 PM
|
Replies: 14
Views: 2,297
1929 u joint
I am in the process of tearing down my 29 roadster pickup. I pulled the trans and was looking at the front u joint. It has a very sloppy fit around what I call the caps. To me the caps are what hold...
|
Forum: Model A (1928-31)
10-24-2020, 05:56 AM
|
Replies: 9
Views: 1,890
Re: installing a front crossmember
Thank you everyone for the helpful information. I am still a ways away from installing. Mac's has a rivet kit for the front crossmember that I probably will purchase. I still am in the process of...
|
Forum: Model A (1928-31)
10-22-2020, 05:05 PM
|
Replies: 9
Views: 1,890
installing a front crossmember
I will be installing a front crossmember on my 29 roadster pickup. Does anyone have any suggestions on what and what not to do? I am hoping to use rivets and get it to look like it should.
|
Forum: Model A (1928-31)
10-10-2020, 12:15 PM
|
Replies: 10
Views: 1,542
|
Forum: Model A (1928-31)
10-08-2020, 06:34 AM
|
Replies: 10
Views: 1,542
1929 front crossmember
I have a 29 Roadster pickup and I am looking for a stock front crossmember. Does anyone know if only a 1929 will fit this or will other years also work? I cannot find one of these at Mac's or...
|