Go Back   The Ford Barn > Search Forums

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 15 of 15
Search took 0.00 seconds.
Search: Posts Made By: Kinsley
Forum: Model A (1928-31) 11-27-2023, 08:08 AM
Replies: 11
Views: 1,235
Posted By Kinsley
Forum: Model A (1928-31) 11-26-2023, 04:23 PM
Replies: 11
Views: 1,235
Posted By Kinsley
Re: clutch/brake pedal bushings

JayJay,
My sense is the way to proceed is, install the repo bushings, remove the grease fitting and drill the bushings in place. Should there be a dowel inserted to support the bushing when drilling?
Forum: Model A (1928-31) 11-25-2023, 01:37 PM
Replies: 11
Views: 1,235
Posted By Kinsley
Re: clutch/brake pedal bushings

My pedals have what appear to be one piece bushings. The bushings I just purchased are two-for-one-pedal, each having a grease hole in the center. Two holes neither of which line up with the grease...
Forum: Model A (1928-31) 08-25-2023, 07:01 AM
Replies: 2
Views: 546
Posted By Kinsley
Forum: Model A (1928-31) 08-24-2023, 07:39 PM
Replies: 2
Views: 546
Posted By Kinsley
wiring harness modification

My car's harness is for no cowl lights, therefore, two wires on the light group for the park bulbs in the headlights. To power my cowls, should I repurpose one of the parklight wires? Based on...
Forum: Model A (1928-31) 06-03-2023, 07:10 PM
Replies: 30
Views: 4,071
Posted By Kinsley
Re: Which tap and die set

I am in the process of setting the carrier bearing preload, as I rebolted the axle on the banjo, I stripped one of the blind holes at the pinion. Will helicoil or a larger bolt work? All 19 other...
Forum: Model A (1928-31) 05-21-2023, 04:15 PM
Replies: 33
Views: 5,881
Posted By Kinsley
Re: Rear axle nut

Bruce, the linked page shows "out of stock". Looks good though.
Forum: Model A (1928-31) 04-26-2023, 10:01 AM
Replies: 7
Views: 1,199
Posted By Kinsley
Re: Canada Bought or Built

I have a '31 T. S. with a CA preface engine number. Interior trim screws and some exterior screws are Robertson ( square hole ) head. I understand this car was built in Canada.
Forum: Model A (1928-31) 02-18-2023, 05:25 PM
Replies: 8
Views: 1,259
Posted By Kinsley
Re: Odometer stops at 99,999

Can a speedo be rewound? Should it rollover to zero after 99,999? Mine is '31 round.
Forum: Model A (1928-31) 05-15-2022, 10:01 AM
Replies: 8
Views: 1,640
Posted By Kinsley
Re: Zenith-1 carb question

I am struggling with a leaking carb when bench testing per "old guy". I am suspecting the drain plug. T. Endy specs black gaskets, the ones I have are red. After the first test I added teflon tape...
Forum: Model A (1928-31) 05-03-2022, 09:32 AM
Replies: 15
Views: 2,167
Posted By Kinsley
Forum: Model A (1928-31) 04-19-2022, 03:49 PM
Replies: 63
Views: 11,193
Posted By Kinsley
Re: What spark plugs are you currently using?

Champion C - 16C What should the gap be?
Forum: Model-A 04-13-2022, 03:31 PM
Replies: 0
Views: 473
Posted By Kinsley
31 Murray SW T. Sedan window regulators

I need all six regulators for this car. I understand they are hens teeth, but I figured if they can be found anywhere they'll be found here.
Forum: Model A (1928-31) 02-22-2022, 03:40 PM
Replies: 15
Views: 2,167
Posted By Kinsley
Re: 29front fender brazed and rivits

What is an aircraft torch?
Forum: Model A (1928-31) 10-17-2021, 04:12 PM
Replies: 106
Views: 13,529
Posted By Kinsley
Showing results 1 to 15 of 15

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:56 AM.