Forum: Late V8 (1954+)
04-26-2022, 03:10 PM
|
Replies: 1
Views: 532
wanted
wanted
1961 through 1964 Ford 262 six-cylinder engine short block or Compleat
engine is ok must be a rebuildable core
Thanks
John Mullen
|
Forum: Late V8
04-26-2022, 03:06 PM
|
Replies: 0
Views: 703
wanted
wanted
1961 through 1964 Ford 262 inline six engine rebuildable core short block or whole engine.
thanks
John Mullen
|
Forum: Early V8 (1932-53)
05-09-2021, 07:15 PM
|
Replies: 7
Views: 1,229
Re: piston fit
that's what I thought they might be, ashtrays it is .. thanks guys
|
Forum: Early V8 (1932-53)
05-06-2021, 03:10 PM
|
Replies: 7
Views: 1,229
piston fit
ok old timers I purchased a NOS set of JAHNS 3 ring pistons at a swap meet and have no paper work to show piston fit. They look like cast Pistons looking on the inside of the skirts where I found the...
|
Forum: Early V8 (1932-53)
08-25-2018, 07:42 PM
|
Replies: 33
Views: 5,156
|
Forum: Early V8 (1932-53)
01-07-2018, 03:32 PM
|
Replies: 3
Views: 1,128
Re: Camshaft Question
you can pull the intake and measure the valve lift at the lifter and compare that to factory specs. It won't tell you the duration without putting a degree wheel on and finding top dead center and...
|
Forum: Late V8 (1954+)
01-07-2018, 10:04 AM
|
Replies: 6
Views: 1,493
|
Forum: Late V8 (1954+)
01-07-2018, 12:58 AM
|
Replies: 6
Views: 1,493
Re: XO/PP Bonneville Project
check out the build with photos and story on the H.A.M.B. main board ...... search... (XO/PP Bonneville Project)
|
Forum: Late V8 (1954+)
01-07-2018, 12:37 AM
|
Replies: 6
Views: 1,493
Re: XO/PP Bonneville Project
Xo stands for engine class (Vintage )PP is production pick up.
the XO/PP rules for the 1961 f100 require a 6 cylinder engine no more than 302 cu. in. displacement. engine must be naturally aspired....
|
Forum: Late V8 (1954+)
01-06-2018, 06:42 PM
|
Replies: 6
Views: 1,493
|
Forum: Early V8 (1932-53)
12-01-2017, 05:06 PM
|
Replies: 1
Views: 586
8BA main bearing caps
I looking for sets of 8BA main bearing caps to try to fit to my very good 8BA block. It had no caps when I purchased it. I hope that someone hear in eastern Virginia, may have some that I can try and...
|
Forum: Early V8 (1932-53)
11-05-2017, 04:05 PM
|
Replies: 21
Views: 5,060
Re: line honing the 8BA main bearing bore
Ron, I have found front and center caps that fit perfectly, however the rear main cap is offset by .004
If you have some rear main caps that you would be willing to ship to me I would pay shipping...
|
Forum: Early V8 (1932-53)
11-02-2017, 06:26 PM
|
Replies: 21
Views: 5,060
line honing the 8BA main bearing bore
I have a 8BA crack free block, however its main caps were lost by previous owner/owners. I have several sets of caps to try to fit and align hone them to this block.. what is the proper procedure to...
|
Forum: Early V8 (1932-53)
10-04-2017, 04:01 PM
|
Replies: 6
Views: 1,908
closed to open drive transmission
what is involved in converting a 1940 ford truck 3 speed top loader transmission to open drive ??..I have a 1940 tranny and want to use it in a 48 to 52 f1 what's needed to change it over ???
|
Forum: Early V8 (1932-53)
02-22-2017, 06:53 PM
|
Replies: 11
Views: 2,838
Re: Flathead Fans, - It can be done!
Dave, Sorry I wasn't there when you picked up your flatty.. Jimmy and I liked that engine very much.. Your cam selection was spot on and I know you will love driving it around .. I will keep an eye...
|
Forum: Questions & Suggestions
01-31-2017, 09:39 PM
|
Replies: 1
Views: 1,419
posting on for sale
why am I not allowed to post on the parts for sale thread. Please advise . Thank You, John Mullen
|
Forum: Late V8
08-22-2015, 10:06 PM
|
Replies: 2
Views: 1,450
|
Forum: Late V8 (1954+)
08-13-2015, 08:19 PM
|
Replies: 3
Views: 1,221
|
Forum: Late V8 (1954+)
08-11-2015, 07:53 PM
|
Replies: 3
Views: 1,221
215/223/262 head ??
I have 2 ford 215/223/262 inline 6 heads (there no good). One has a small oval shaped combustion chamber and one has a triangle shaped one . I want another small chamber head but don't know just what...
|
Forum: Late V8
08-04-2015, 01:09 PM
|
Replies: 2
Views: 1,450
|
Forum: Late V8
07-01-2015, 10:16 PM
|
Replies: 2
Views: 1,450
|
Forum: Early V8
05-12-2015, 07:13 PM
|
Replies: 2
Views: 1,301
|
Forum: Early V8
04-27-2015, 04:12 PM
|
Replies: 2
Views: 1,301
|
Forum: Early V8
04-23-2015, 06:55 PM
|
Replies: 2
Views: 1,301
stromberg 97 big logo carb float bowl section
I am in need of a Stromberg 97 big logo center section .Mine is not serviceable ... just the bowl section is all I need .Please reply with cost if you can help...Thanks John Mullen
|
Forum: Early V8 (1932-53)
04-20-2015, 07:20 PM
|
Replies: 16
Views: 3,859
Re: flathead line bore
I purchased a main cap set off the e/net and they fit so close that I can't believe my eye's. I'm thinking I want to have them very lightly honed just to be sure they are ok.
|