Forum: Model A (1928-31)
02-01-2017, 12:25 AM
|
Replies: 242
Views: 75,047
|
Forum: Model A (1928-31)
02-01-2017, 12:21 AM
|
Replies: 242
Views: 75,047
|
Forum: Model A (1928-31)
01-02-2017, 11:59 PM
|
Replies: 25
Views: 4,393
|
Forum: Model A (1928-31)
11-01-2015, 07:52 PM
|
Replies: 22
Views: 3,895
|
Forum: Model A (1928-31)
10-25-2015, 05:45 PM
|
Replies: 24
Views: 19,536
|
Forum: Model A (1928-31)
10-16-2015, 11:56 AM
|
Replies: 11
Views: 2,118
Re: Battery Filler
No. I use a Turkey baster, it works good. And I get my distilled water free form my air conditioner.
|
Forum: Model A (1928-31)
10-08-2015, 05:38 PM
|
Replies: 1
Views: 999
Re: Dash cables replacing
Finished the installation and my engine runs smoother, why? I assume that because the old wires were farmer fabricated and too long and undersized. I replaced the other underhood harness as well.
|
Forum: Model A (1928-31)
10-07-2015, 02:52 PM
|
Replies: 3
Views: 1,341
|
Forum: Model A (1928-31)
10-07-2015, 02:51 PM
|
Replies: 8
Views: 2,032
Decent quality amp meter?
Does anyone make a decent quality amp meter. Chinese needle fell of the pivots just from turning over the dash to bent the mounting tabs. I am thinking of going digital. I will try to repair it?
|
Forum: Model A (1928-31)
10-07-2015, 12:57 PM
|
Replies: 3
Views: 1,341
|
Forum: Model A (1928-31)
09-26-2015, 01:38 PM
|
Replies: 19
Views: 3,675
|
Forum: Model A (1928-31)
09-26-2015, 01:36 PM
|
Replies: 1
Views: 999
Dash cables replacing
I am now replacing all the wires that go from the terminal box to the dash. The old one were ready to short out and I recommend that you replace yours. (and add a fuse)!
|
Forum: Model A (1928-31)
09-15-2015, 05:09 PM
|
Replies: 4
Views: 1,524
Complete draining of coolant?
The specification says three gallons. I get only two gallons through the petcock. Does this mean that I had been low on coolant or there is still one gallon in the system?
|
Forum: Model A (1928-31)
09-15-2015, 02:04 PM
|
Replies: 15
Views: 2,380
|
Forum: Model A (1928-31)
09-08-2015, 07:13 PM
|
Replies: 9
Views: 2,050
|
Forum: Model A (1928-31)
09-08-2015, 03:09 PM
|
Replies: 10
Views: 3,096
Re: Installing a mechanical temperature gauge?
Thanks to all. I hadn't thought about routing it through the floorboard (DUH!).
I will get started soon. Thanks also for the confirmation that a thermostat is needed. I already have that and no...
|
Forum: Model A (1928-31)
09-06-2015, 11:15 PM
|
Replies: 10
Views: 3,096
|
Forum: Model A (1928-31)
09-06-2015, 10:17 PM
|
Replies: 10
Views: 3,096
Installing a mechanical temperature gauge?
I have all the needed parts to install said gauge, but I am wondering what to do with the excess length of lead to the probe. Yes, I know I can't cut it.
My thought is too bundle it up loosely in...
|
Forum: Model A (1928-31)
08-22-2015, 07:34 PM
|
Replies: 7
Views: 1,402
Re: Gap in hood
Mitch,I did have the hood off last year and don't remember it being that far off. Glenn, I just noticed pads between the frame and radiator mount. I don't think they should be there, but not sure. ...
|
Forum: Model A (1928-31)
08-22-2015, 04:04 PM
|
Replies: 7
Views: 1,402
Gap in hood
I have a moderately severe gap at the rear of my hood. I have read past post about shimming the cowl, but my doors look about level. I suspect that the radiator is too high. What do you think and...
|
Forum: Model A (1928-31)
07-30-2015, 09:03 PM
|
Replies: 7
Views: 2,048
|
Forum: Model A (1928-31)
07-29-2015, 08:41 PM
|
Replies: 7
Views: 2,048
Re: Canadian Tail Light Bracket - Tudor
Mine is bent from the original owner. The license plate is on an angle and the bracket is too close to the fender. Could the person who looked up the part number please post it?
|
Forum: Model A (1928-31)
07-28-2015, 04:26 PM
|
Replies: 7
Views: 2,048
Canadian Tail Light Bracket - Tudor
My Tudor came from Quebec and has several differences from the US version. The one bothering my right now is the drum taillight bracket. Snyders has one that looked similar, but is more flat. The...
|
Forum: Model A (1928-31)
07-23-2015, 11:20 AM
|
Replies: 25
Views: 7,539
Re: Straightening exhause oioe
I took mine to Midas Muffler, he heated it with a torch and with a long pipe, bent it to my spec. Didn't charge me a cent.
|
Forum: Model A (1928-31)
07-21-2015, 06:42 PM
|
Replies: 3
Views: 1,920
compression test gauge
I am wondering what you guys are using to test compression. The kits I see are expensive and don't have a 7/8" capability. I imagine that it would be required to wrap several layer of tape around...
|